Developing Lengths in Horizontal Two-Phase Bubbly Flow

1995 ◽  
Vol 117 (3) ◽  
pp. 512-518 ◽  
Author(s):  
B. A. Warren ◽  
J. F. Klausner
Keyword(s):  
Pressure Drop ◽  
Two Phase Flow ◽  
Volume Fraction ◽  
Bubbly Flow ◽  
Phase Flow ◽  
Flow Conditions ◽  
Relative Deviation ◽  
Two Phase ◽  
Fully Developed Flow ◽  
Local Measurements

An air-water two-phase flow facility with a 19.1 mm i.d. test section has been fabricated. Local measurements of pressure drop for two-phase horizontal bubbly flow and single-phase flow downstream of various orifices have been obtained over a range of flow conditions. The wall shear stress developing length is obtained from the pressure drop profile. A developing length correlation is presented in which the relative deviation is 6 percent. The fully developed vapor volume fraction has also been measured up- and downstream of the orifice. A simple correlation for vapor volume fraction is presented in which the relative deviation is 7 percent. Photographs of the two-phase flow pattern in the developing region reveal that the flow structure is extremely complex and continuously evolves until approximately fully developed flow conditions are achieved.

Prediction of Pump Performance Under Air-Water Two-Phase Flow Based on a Bubbly Flow Model

1993 ◽  
Vol 115 (4) ◽  
pp. 781-783 ◽  
Author(s):  
Kiyoshi Minemura ◽  
Tomomi Uchiyama
Keyword(s):  
Two Phase Flow ◽  
Bubbly Flow ◽  
Phase Flow ◽  
Centrifugal Pumps ◽  
Flow Conditions ◽  
Two Phase ◽  
Performance Change ◽  
Void Fractions ◽  
Two Phases

This paper is concerned with the determination of the performance change in centrifugal pumps operating under two-phase flow conditions using the velocities and void fractions calculated under the assumption of an inviscid bubbly flow with slippage between the two phases. The estimated changes in the theoretical head are confirmed with experiments within the range of bubbly flow regime.

scholarly journals Numerical and experimental studies of gas–liquid flow and pressure drop in multiphase pump valves

2020 ◽  
Vol 103 (3) ◽  
pp. 003685042094088
Author(s):  
Yi Ma ◽  
Minjia Zhang ◽  
Huashuai Luo
Keyword(s):  
Pressure Drop ◽  
Two Phase Flow ◽  
Volume Fraction ◽  
Test System ◽  
Ball Valve ◽  
Phase Flow ◽  
Two Phase ◽  
Pressure Drops ◽  
Disk Valve ◽  
Predicted Values

A numerical and experimental study was carried out to investigate the two-phase flow fields of the typical three valves used in the multiphase pumps. Under the gas volume fraction conditions in the range of 0%–100%, the three-dimensional steady and dynamic two-phase flow characteristics, pressure drops, and their multipliers of the ball valve, cone valve, and disk valve were studied, respectively, using Eulerian–Eulerian approach and dynamic grid technique in ANSYS FLUENT. In addition, a valve test system was built to verify the simulated results by the particle image velocimetry and pressure test. The flow coefficient CQ (about 0.989) of the disk valve is greater than those of the other valves (about 0.864) under the steady flow with a high Reynolds number. The two-phase pressure drops of the three valves fluctuate in different forms with the vibration of the cores during the dynamic opening. The two-phase multipliers of the fully opened ball valve are consistent with the predicted values of the Morris model, while those of the cone valve and disk valve had the smallest differences with the predicted values of the Chisholm model. Through the comprehensive analysis of the flow performance, pressure drop, and dynamic stability of the three pump valves, the disk valve is found to be more suitable for the multiphase pumps due to its smaller axial space, resistance loss, and better flow capacity.

Towards Understanding Two-Phase Flow Induced Vibration of Piping Structure With a U-Bend

2019 ◽  
Author(s):  
Olufemi E. Bamidele ◽  
Wael H. Ahmed ◽  
Marwan Hassan
Keyword(s):  
Void Fraction ◽  
Vibration Amplitude ◽  
Two Phase Flow ◽  
Bubbly Flow ◽  
Phase Flow ◽  
Flow Conditions ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Void Fractions ◽  
Flow Induced Vibrations

Abstract The current work investigates two-phase flow induced vibrations in 90° U-bend. The two-phase induced vibration of the structure was investigated in the vertical, horizontal and axial directions for various flow patterns from bubbly flow to wavy and annular-dispersed flow. The void fractions at various locations along the piping including the fully developed void fraction and the void fraction at the entrance of the U-bend were fully investigated and correlated with the vibration amplitude. The results show that the excitation forces of the two-phase flow in a piping structure are highly dependent on the flow pattern and the flow conditions upstream of the bend. The fully developed void fraction and slip between phases are important in modelling of forces in U-bends and elbows.

scholarly journals Slug Regime Transitions in a Two-Phase Flow in Horizontal Round Pipe. CFD Simulations

2020 ◽  
Vol 10 (23) ◽  
pp. 8739
Author(s):  
Vitaly Sergeev ◽  
Nikolai Vatin ◽  
Evgeny Kotov ◽  
Darya Nemova ◽  
Svyatoslav Khorobrov
Keyword(s):  
Pressure Drop ◽  
Flow Regime ◽  
Two Phase Flow ◽  
Stokes Equations ◽  
Bubbly Flow ◽  
Fluid Motion ◽  
Navier Stokes ◽  
Technical Solution ◽  
Phase Flow ◽  
Two Phase

The main objective of the study is to propose a technical solution integrated into the pipeline for the transition of the flow regime from slug to bubbly two-phase flow. The object of research is isothermal two-phase gas–Newtonian-liquid flow in a horizontal circular pipeline. There is local resistance in the pipe in the form of a streamlined transverse mesh partition. The mesh partition ensures the transition of the flow from the slug regime to the bubbly regime. The purpose of the study is to propose a technical solution integrated into the pipeline for changing the flow regime of a two-phase flow from slug to bubbly flow. The method of research is a simulation using computational fluid dynamics (CFD) numerical simulation. The Navier–Stokes equations averaged by Reynolds describes the fluid motion. The k-ε models were used to close the Reynolds-averaged Navier–Stokes (RANS) equations. The computing cluster «Polytechnic—RSK Tornado» was used to solve the tasks. The results of simulation show that pressure drop on the grid did not exceed 10% of the pressure drop along the length of the pipeline. The mesh partition transits the flow regime from slug to layered one, which will help to increase the service life and operational safety of a real pipeline at insignificant energy costs to overcome the additional resistance integrated into the pipeline.

scholarly journals Investigation on the Handling Ability of Centrifugal Pumps under Air–Water Two-Phase Inflow: Model and Experimental Validation

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3048 ◽  
Author(s):  
Qiaorui Si ◽  
Gérard Bois ◽  
Qifeng Jiang ◽  
Wenting He ◽  
Asad Ali ◽  
...  
Keyword(s):  
Centrifugal Pump ◽  
Two Phase Flow ◽  
Bubbly Flow ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Phase Flow ◽  
Centrifugal Pumps ◽  
Flow Conditions ◽  
Two Phase ◽  
Local Flow

The paper presents experimental and numerical investigations performed on a single stage, single-suction, horizontal-orientated centrifugal pump in air–water two-phase non-condensable flow conditions. Experimental measurements are performed in a centrifugal pump using pressure sensor devices in order to measure the wall static pressures at the inlet and outlet pump sections for different flow rates and rotational speeds combined with several air void fraction (a) values. Two different approaches are used in order to predict the pump performance degradations and perform comparisons with experiments for two-phase flow conditions: a one-dimensional two-phase bubbly flow model, and a full “Three-Dimensional Unsteady Reynolds Average Navier–Stokes” (3D-URANS) simulation using a modified k-epsilon turbulence model combined with the Euler–Euler inhomogeneous two-phase flow description. The overall and local flow features are presented and analyzed. Limitations concerning both approaches are pointed out according to some flow physical assumptions and measurement accuracies. Some additional suggestions are proposed in order to improve two-phase flow pump suction capabilities.

scholarly journals Experimental Investigation of the Vertical Upward Single- and Two-Phase Flow Pressure Drops Through Gate and Ball Valves

2019 ◽  
Vol 142 (2) ◽  
Author(s):  
Ammar Zeghloul ◽  
Hiba Bouyahiaoui ◽  
Abdelwahid Azzi ◽  
Abbas H. Hasan ◽  
Abdelsalam Al-sarkhi
Keyword(s):  
Experimental Investigation ◽  
Pressure Drop ◽  
Single Phase ◽  
Gate Valve ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Flow Conditions ◽  
Two Phase ◽  
Pressure Drops ◽  
Flow Pressure

Abstract This paper presents an experimental investigation of the pressure drop (DP) through valves in vertical upward flows. Experiments were carried out using a 1¼″ (DN 32) ball and gate valve. Five opening areas have been investigated from fully open to the nearly fully closed valve, using air with a superficial velocity of 0–3.5 m/s and water 0.05–0.91 m/s. These ranges cover single-phase and the bubbly, slug and churn two-phase flow regimes. It was found that for the single-phase flow experiments, the valve coefficient increases with the valve opening and is the same, in both valves, for the openings smaller than 40%. The single-phase pressure drop increases with the liquid flowrate and decreases with the opening area. The two-phase flow pressure drop was found considerably increased by reducing the opening area for both valves. It reaches its maximum values at 20% opening for the ball valve and 19% opening for the gate valve. It was also inferred that at fully opening condition, the two-phase flow multiplier, for both valves, has been found close to unity for most of the tested flow conditions. For 40 and 20% valve openings the two-phase multiplier decreases in the power-law with liquid holdup for the studied flow conditions. Models proposed originally for evaluating the pressure drop through an orifice in single-phase and two-phase flows were also applied and assessed in the present experimental data.

Comparison of Local Interfacial Structures Around 90 and 45-Degree Elbows in Horizontal Bubbly Flows

2010 ◽  
Vol 132 (11) ◽  
Author(s):  
Mohan Yadav ◽  
Justin D. Talley ◽  
Seungjin Kim
Keyword(s):  
Test Section ◽  
Two Phase Flow ◽  
Bubbly Flow ◽  
Phase Flow ◽  
Flow Conditions ◽  
Local Data ◽  
Two Phase ◽  
Flow Parameters ◽  
Interfacial Structures ◽  
Spatial Oscillations

This study presents a comparison of the geometric effects of 90 deg and 45 deg elbows in horizontal two-phase air-water bubbly flow. Two separate experiments were performed in the horizontal test section made out of 50.3 mm inner diameter glass tubes. The first set of data was collected with a 90 deg elbow installed, and then a 45 deg elbow was added to the existing facility to acquire the second set of data. A total of 15 different flow conditions, all within the bubbly flow regime, were identified for the 90 deg experiment, and very similar flow conditions were extended to the 45 deg experiment. A double-sensor conductivity probe was employed to acquire the local data at seven different axial positions along the test section, out of which four measurement locations are associated with the 90 deg experiment and three with the 45 deg experiment. The data show that the elbows have a significant effect on the development of interfacial structures as well as the bubble interaction mechanisms. Furthermore, there are characteristic similarities and differences between the effects of the two elbows. While the effect of the 45 deg elbow is evident immediately after the elbow, the 90 deg elbow effect tends to propagate further downstream of the elbow rather than immediately after the elbow. Moreover, it is shown that both elbows induce spatial oscillations in the interfacial structures and two-phase flow parameters, but the degree and the nature of oscillations differ. The effects of the elbows are also compared for the axial transport of the two-phase flow parameters.

MODELING OF THE MINIMIZED TWO-PHASE FLOW FRICTIONAL PRESSURE DROP IN A SMALL TUBE WITH DIFFERENT CORRELATIONS

2016 ◽  
Vol 78 (6-11) ◽  
Author(s):  
Qais Abid Yousif ◽  
Normah Mohd-Ghazali ◽  
Nor Atiqah Zolpakar ◽  
Sentot Novianto ◽  
Agus Sujiantro Pamitran ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Surface Roughness ◽  
Pressure Drop ◽  
Laminar Flow ◽  
Friction Factor ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Flow Conditions ◽  
Two Phase ◽  
Frictional Pressure Drop

The major parameters of interest in heat transfer research are the refrigerant charge, pressure drop, and heat transfer capacity. Smaller channels reduce the refrigerant charge with higher heat transfer capability due to the increased in surface area to volume ratio but at the expense of a higher pressure drop. Differences between the predicted and experimental frictional pressure drop of two-phase flow in small tubes have frequently been discussed. Factors that could have contributed to that effect have been attributed to the correlations used to model the flow, some being modified from the originals developed for a macro system. Experimental test-rigs have varied in channel geometry, refrigerant type, and flow conditions. Thousands of data have been collected to find a common point among the differences. This paper reports an investigation of four different two-phase friction factor correlations used in the modeling of the frictional two-phase flow pressure drop of refrigerant R-22. One had been specifically developed for laminar flow in a smooth channel, another was modified from a laminar flow in a smooth pipe to be used for a rough channel, and two correlations are specific for turbulent flow that consider internal pipe surface roughness. Genetic algorithm, an optimization scheme, is used to search for the minimum friction factor and minimum frictional pressure drop under optimized conditions of the mass flux and vapor quality. The results show that a larger pressure drop does come with a smaller channel. A large discrepancy exists between the correlations investigated; between the ones that does not consider surface roughness and that which does, as well as between flow under laminar and turbulent flow conditions.

The effect of spacer grid critical component on pressure drop under both single and two phase flow conditions

Kerntechnik ◽  
2016 ◽  
Vol 81 (3) ◽  
pp. 257-267 ◽  
Author(s):  
B. Han ◽  
B.-W. Yang ◽  
H. Zhang ◽  
H. Mao ◽  
Y. Zha
Keyword(s):  
Pressure Drop ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Critical Component ◽  
Flow Conditions ◽  
Spacer Grid ◽  
Two Phase

Numerical Simulations of Two-Phase Flow in a Fuel Assembly of Blockage due to LOCA

2017 ◽  
Author(s):  
Jingwen Ren ◽  
Fenglei Niu ◽  
Weiqian Zhuo ◽  
Da Wang
Keyword(s):  
Pressure Drop ◽  
Numerical Simulations ◽  
Fuel Assembly ◽  
Water Flow ◽  
Two Phase Flow ◽  
Volume Fraction ◽  
Particle Diameter ◽  
High Energy ◽  
Phase Flow ◽  
Two Phase

During a LOCA accident, the debris caused by the action of high energy fluid discharged from the break may transport to the containment sump, then may be entrained into the core by the ECCS water. The debris may cause the blockage of fuel assembly. The air may also enter the reactor with water. Numerical simulations are performed to analyze the air-water flow and particle-water flow through the blocked fuel assembly. The pressure drop in fuel assembly will impact the long-term core cooling capability. The effects of different parameters on the pressure drop over the fuel assembly are analyzed. Pressure drop increases as blockage percentage, mass flow rate or inlet velocity increases for both two-phase flow. The decrease of air volume fraction and the increase of particle volume fraction all cause the increase of pressure drop. Pressure drop increases slightly as bubble diameter increases, and the tiny effect of particle diameter on pressure drop was found as particle diameter varying at an increment of 10um.

Sign in / Sign up

Export Citation Format

Share Document