Comparison of Emissions and Efficiency of a Turbocharged Lean-Burn Natural Gas and Hythane-Fueled Engine

1997 ◽  
Vol 119 (1) ◽  
pp. 218-226 ◽  
Author(s):  
J. F. Larsen ◽  
J. S. Wallace
Keyword(s):  
Natural Gas ◽  
Specific Energy Consumption ◽  
Oxides Of Nitrogen ◽  
Heavy Duty ◽  
Lean Burn ◽  
Clear Trend ◽  
Engine Operation ◽  
Spark Timing ◽  
Test Engine ◽  
Carbon Dioxide Co2

An experiment was conducted to evaluate the potential for reduced exhaust emissions and improved efficiency, by way of lean-burn engine fuelling with hydrogen supplemented natural gas (Hythane). The emissions and efficiency of the Hythane fuel (15 percent hydrogen, 85 percent natural gas by volume), were compared to the emissions and efficiency of pure natural gas using a turbocharged, spark ignition, 3.1 L, V-6 engine. The feasibility of heavy duty engine fueling with Hythane was assessed through testing conducted at engine speed and load combinations typical of heavy-duty engine operation. Comparison of the efficiency and emissions at MBT spark timing revealed that Hythane fueling of the test engine resulted in consistently lower brake specific energy consumption and emissions of total hydrocarbons (THC), carbon monoxide (CO), and carbon dioxide (CO2), at a given equivalence ratio. There was no clear trend with respect to MBT oxides of nitrogen (NOx) emissions. It was also discovered that an improved NOx-THC tradeoff resulted when Hythane was used to fuel the test engine. Consequently, Hythane engine operating parameters can be adjusted to achieve a concurrent reduction in NOx and THC emissions relative to natural gas fueling.

Experimental Investigation of a Heavy-Duty CI Engine Retrofitted to Natural Gas SI Operation

2018 ◽  
Author(s):  
Jinlong Liu ◽  
Hemanth Bommisetty ◽  
Cosmin E. Dumitrescu
Keyword(s):  
Natural Gas ◽  
Operating Conditions ◽  
Intake Manifold ◽  
Heavy Duty ◽  
Lean Burn ◽  
Engine Operation ◽  
Cycle Variation ◽  
Spark Timing ◽  
Ci Engine ◽  
Ci Engines

Heavy-duty compression-ignition (CI) engines converted to natural gas (NG) operation can reduce the dependence on petroleum-based fuels and curtail greenhouse gas emissions. Such an engine was converted to premixed NG spark-ignition (SI) operation through the addition of a gas injector in the intake manifold and of a spark plug in place of the diesel injector. Engine performance and combustion characteristics were investigated at several lean-burn operating conditions that changed fuel composition, spark timing, equivalence ratio, and engine speed. While the engine operation was stable, the reentrant bowl-in-piston (a characteristic of a CI engine) influenced the combustion event such as producing a significant late-combustion, particularly for advanced spark timing. This was due to an important fraction of the fuel burning late in the squish region, which affected the end of combustion, the combustion duration, and the cycle-to-cycle variation. However, the lower cycle-to-cycle variation, stable combustion event, and the lack of knocking suggest a successful conversion of conventional diesel engines to NG SI operation using the approach described here.

Experimental Investigation of a Heavy-Duty Compression-Ignition Engine Retrofitted to Natural Gas Spark-Ignition Operation

2019 ◽  
Vol 141 (11) ◽  
Author(s):  
Jinlong Liu ◽  
Hemanth Kumar Bommisetty ◽  
Cosmin Emil Dumitrescu
Keyword(s):  
Natural Gas ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Compression Ignition ◽  
Heavy Duty ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Cycle Variation ◽  
Spark Timing ◽  
Ci Engines

Heavy-duty compression-ignition (CI) engines converted to natural gas (NG) operation can reduce the dependence on petroleum-based fuels and curtail greenhouse gas emissions. Such an engine was converted to premixed NG spark-ignition (SI) operation through the addition of a gas injector in the intake manifold and of a spark plug in place of the diesel injector. Engine performance and combustion characteristics were investigated at several lean-burn operating conditions that changed fuel composition, spark timing, equivalence ratio, and engine speed. While the engine operation was stable, the reentrant bowl-in-piston (a characteristic of a CI engine) influenced the combustion event such as producing a significant late combustion, particularly for advanced spark timing. This was due to an important fraction of the fuel burning late in the squish region, which affected the end of combustion, the combustion duration, and the cycle-to-cycle variation. However, the lower cycle-to-cycle variation, stable combustion event, and the lack of knocking suggest a successful conversion of conventional diesel engines to NG SI operation using the approach described here.

Lean-Burn Characteristics of a Heavy-Duty Diesel Engine Retrofitted to Natural Gas Spark Ignition

2018 ◽  
Author(s):  
Jinlong Liu ◽  
Cosmin E. Dumitrescu
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Fuel Injector ◽  
Heavy Duty ◽  
Lean Burn ◽  
Spark Timing ◽  
Heavy Duty Diesel

Increased utilization of natural-gas (NG) in the transportation sector can decrease the use of petroleum-based fuels and reduce greenhouse-gas emissions. Heavy-duty diesel engines retrofitted to NG spark ignition (SI) can achieve higher efficiencies and low NOx, CO, and HC emissions when operated under lean-burn conditions. To investigate the SI lean-burn combustion phenomena in a bowl-in-piston combustion chamber, a conventional heavy-duty direct-injection CI engine was converted to SI operation by replacing the fuel injector with a spark plug and by fumigating NG in the intake manifold. Steady-state engine experiments and numerical simulations were performed at several operating conditions that changed spark timing, engine speed, and mixture equivalence ratio. Results suggested a two-zone NG combustion inside the diesel-like combustion chamber. More frequent and significant late burn (including double-peak heat release rate) was observed for advanced spark timing. This was due to the chamber geometry affecting the local flame speed, which resulted in a faster and thicker flame in the bowl but a slower and thinner flame in the squish volume. Good combustion stability (COVIMEP < 3 %), moderate rate of pressure rise, and lack of knocking showed promise for heavy-duty CI engines converted to NG SI operation.

Lean-Burn Stationary Natural Gas Reciprocating Engine Operation With a Prototype Fiber Coupled Diode End Pumped Passively Q-Switched Laser Spark Plug

2009 ◽  
Author(s):  
Dustin L. McIntyre ◽  
Steven D. Woodruff ◽  
John S. Ontko
Keyword(s):  
Natural Gas ◽  
Optical Fiber ◽  
Optical Power ◽  
Boost Pressure ◽  
Lean Burn ◽  
Engine Operation ◽  
Pump Source ◽  
Spark Plug ◽  
Spark Timing ◽  
Laser Spark

An end pumped passively Q-switched laser igniter was developed to meet the ignition system needs of large bore lean burn stationary natural gas engines. The laser spark plug used an optical fiber coupled diode pump source to axially pump a passively Q-switched Nd:YAG laser and transmit the laser pulse through a custom designed lens. The optical fiber coupled pump source permits the excitation energy to be transmitted to the spark plug at relatively low optical power, less than 250 watts. The Q-switched laser then generates as much as 8 millijoules of light in 2.5 nanoseconds which is focused through an asymmetric biconvex lens to create a laser spark from a focused intensity of approximately 225 GW/cm2. A single cylinder engine fueled with either natural gas only or hydrogen augmented natural gas was operated with the laser spark plug for approximately 10 hours in tests spanning 4 days. The tests were conducted with fixed engine speed, fixed boost pressure, no exhaust gas recirculation, and laser spark timing advance set at maximum brake torque timing. Engine operational and emissions data were collected and analyzed.

Precombustion Chamber Design for Emissions Reduction From Large Bore NG Engines

2010 ◽  
Vol 132 (12) ◽  
Author(s):  
Dean J. Simpson ◽  
Daniel B. Olsen
Keyword(s):  
Natural Gas ◽  
Combustion Stability ◽  
Nozzle Geometry ◽  
Oxides Of Nitrogen ◽  
Lean Burn ◽  
Engine Operation ◽  
Chamber Volume ◽  
Fuel Delivery ◽  
Design Variables ◽  
Partial Load

Precombustion chambers (PCCs) are an ignition technology for large bore, natural gas engines, which can extend the lean operating limit through improved combustion stability. Previous research indicates that the PCC is responsible for a significant portion of engine-out emissions, especially near the lean limit of engine operation. In this work, six concept PCC designs are developed with the objective of reducing engine-out emissions, focusing on oxides of nitrogen (NOx). The design variables include chamber geometry, chamber volume, fuel delivery, nozzle geometry, and material thermal conductivity. The concepts are tested on a single cylinder of a large bore, two-stroke cycle, lean burn, natural gas compressor engine, and the results are compared with stock PCC performance. The pollutants of interest include NOx, carbon monoxide, total hydrocarbons, and volatile organic compounds (VOCs). The results indicate that PCC volume has the largest effect on the overall NOx–CO tradeoff. Multiple nozzles and electronic PCC fuel control were found to enhance main chamber combustion stability, particularly at partial load conditions. The PCC influence on VOCs was insignificant; rather, VOCs were found to be heavily dependent on fuel composition.

Lean-Burn Stationary Natural Gas Engine Operation With a Prototype Laser Spark Plug

2010 ◽  
Vol 132 (7) ◽  
Author(s):  
Dustin L. McIntyre ◽  
Steven D. Woodruff ◽  
John S. Ontko
Keyword(s):  
Natural Gas ◽  
Optical Fiber ◽  
Optical Power ◽  
Boost Pressure ◽  
Lean Burn ◽  
Engine Operation ◽  
Pump Source ◽  
Spark Plug ◽  
Spark Timing ◽  
Laser Spark

An end pumped passively Q-switched laser igniter was developed to meet the ignition system needs of large bore lean burn stationary natural gas engines. The laser spark plug used an optical fiber coupled diode pump source to axially pump a passively Q-switched Nd:YAG laser and transmit the laser pulse through a custom designed lens. The optical fiber coupled pump source permits the excitation energy to be transmitted to the spark plug at relatively low optical power, less than 250 W. The Q-switched laser then generates as much as 8 mJ of light in 2.5 ns, which is focused through an asymmetric biconvex lens to create a laser spark from a focused intensity of approximately 225 GW/cm2. A single cylinder engine fueled with either natural gas only or hydrogen augmented natural gas was operated with the laser spark plug for approximately 10 h in tests spanning 4 days. The tests were conducted with fixed engine speed, fixed boost pressure, no exhaust gas recirculation, and laser spark timing advance set at maximum brake torque timing. Engine operational and emissions data were collected and analyzed.

Lean-Burn Characteristics of a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark Ignition

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Jinlong Liu ◽  
Cosmin Emil Dumitrescu
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Fuel Injector ◽  
Heavy Duty ◽  
Lean Burn ◽  
Heavy Duty Diesel ◽  
Ci Engines

Increased utilization of natural gas (NG) in the transportation sector can decrease the use of petroleum-based fuels and reduced greenhouse gas emissions. Heavy-duty diesel engines retrofitted to NG spark ignition (SI) can achieve higher efficiencies and low NOX, CO, and hydrocarbon (HC) emissions when operated under lean-burn conditions. To investigate the SI lean-burn combustion phenomena in a bowl-in-piston combustion chamber, a conventional heavy-duty direct-injection CI engine was converted to SI operation by replacing the fuel injector with a spark plug and by fumigating NG in the intake manifold. Steady-state engine experiments and numerical simulations were performed at several operating conditions that changed spark timing (ST), engine speed, and mixture equivalence ratio. Results suggested a two-zone NG combustion inside the diesel-like combustion chamber. More frequent and significant late-burn (including double-peak heat release rate) was observed for advanced ST. This was due to the chamber geometry affecting the local flame speed, which resulted in a faster and thicker flame in the bowl but a slower and thinner flame in the squish volume. Good combustion stability (COVIMEP < 3%), moderate rate of pressure-rise, and lack of knocking showed promise for heavy-duty CI engines converted to NG SI operation.

Sign in / Sign up

Export Citation Format

Share Document