On the Relative Roles of Fuel Spray Kinetic Energy and Engine Speed in Determining Mixing Rates in D.I. Diesel Engines

1997 ◽  
Vol 119 (1) ◽  
pp. 212-217 ◽  
Author(s):  
W. J. Smith ◽  
D. J. Timoney
Keyword(s):  
Kinetic Energy ◽  
Diesel Engines ◽  
Engine Speed ◽  
Fuel Injection ◽  
Injection System ◽  
Dominant Factor ◽  
Mixing Times ◽  
Air Mixing ◽  
Mixing Rates ◽  
Air Motion

This paper describes an attempt to separate out and to quantify the relative importance of fuel injection characteristics and in-cylinder air motion as factors influencing the rate of fuel-air mixing and of combustion in high-speed D.I. diesel engines, where bulk swirling air motion is absent. Tests on a 121 mm bore × 139 mm stroke, 1.6 liter, single-cylinder engine at constant engine speed reveal substantially shorter fuel-air mixing times as the mean fuel injection kinetic energy (M.I.K.E.) is increased. Also, tests at constant injection kinetic energy but with varying engine speed (involving different fuel injection system builds at each speed) show that fuel-air mixing times are reduced at higher engine speeds. From these trends it is concluded that, while injection kinetic energy is the dominant factor in determining fuel-air mixing rates in D.I. diesels, small-scale turbulent air motions, the intensity and structure of which are related to engine speed, also exert an important influence on the mixing rate.

An Improved Rate of Heat Release Model for Modern High-Speed Diesel Engines

2017 ◽  
Vol 139 (9) ◽  
Author(s):  
Peter G. Dowell ◽  
Sam Akehurst ◽  
Richard D. Burke
Keyword(s):  
Heat Release ◽  
Diesel Engines ◽  
Engine Speed ◽  
Fuel Injection ◽  
Maximum Pressure ◽  
Injection Model ◽  
Wall Impingement ◽  
Small Set ◽  
Rate Of Heat Release ◽  
Engine System

To meet the increasingly stringent emissions standards, diesel engines need to include more active technologies with their associated control systems. Hardware-in-the-loop (HiL) approaches are becoming popular where the engine system is represented as a real-time capable model to allow development of the controller hardware and software without the need for the real engine system. This paper focusses on the engine model required in such approaches. A number of semi-physical, zero-dimensional combustion modeling techniques are enhanced and combined into a complete model, these include—ignition delay, premixed and diffusion combustion and wall impingement. In addition, a fuel injection model was used to provide fuel injection rate from solenoid energizing signals. The model was parameterized using a small set of experimental data from an engine dynamometer test facility and validated against a complete data set covering the full engine speed and torque range. The model was shown to characterize the rate of heat release (RoHR) well over the engine speed and load range. Critically, the wall impingement model improved R2 value for maximum RoHR from 0.89 to 0.96. This was reflected in the model's ability to match both pilot and main combustion phasing, and peak heat release rates derived from measured data. The model predicted indicated mean effective pressure and maximum pressure with R2 values of 0.99 across the engine map. The worst prediction was for the angle of maximum pressure which had an R2 of 0.74. The results demonstrate the predictive ability of the model, with only a small set of empirical data for training—this is a key advantage over conventional methods. The fuel injection model yielded good results for predicted injection quantity (R2 = 0.99) and enabled the use of the RoHR model without the need for measured rate of injection.

scholarly journals Possibilities of Simultaneous In-Cylinder Reduction of Soot andNOxEmissions for Diesel Engines with Direct Injection

2008 ◽  
Vol 2008 ◽  
pp. 1-13 ◽  
Author(s):  
U. Wagner ◽  
P. Eckert ◽  
U. Spicher
Keyword(s):  
Nitrogen Oxide ◽  
Diesel Engines ◽  
Fuel Injection ◽  
Soot Formation ◽  
Soot Oxidation ◽  
The Other ◽  
Injection System ◽  
Nitrogen Oxide Emissions ◽  
Injection Strategy ◽  
Soot Emissions

Up to now, diesel engines with direct fuel injection are the propulsion systems with the highest efficiency for mobile applications. Future targets in reducingCO2-emissions with regard to global warming effects can be met with the help of these engines. A major disadvantage of diesel engines is the high soot and nitrogen oxide emissions which cannot be reduced completely with only engine measures today. The present paper describes two different possibilities for the simultaneous in-cylinder reduction of soot and nitrogen oxide emissions. One possibility is the optimization of the injection process with a new injection strategy the other one is the use of water diesel emulsions with the conventional injection system. The new injection strategy for this experimental part of the study overcomes the problem of increased soot emissions with pilot injection by separating the injections spatially and therefore on the one hand reduces the soot formation during the early stages of the combustion and on the other hand increases the soot oxidation later during the combustion. Another method to reduce the emissions is the introduction of water into the combustion chamber. Emulsions of water and fuel offer the potential to simultaneously reduceNOxand soot emissions while maintaining a high-thermal efficiency. This article presents a theoretical investigation of the use of fuel-water emulsions in DI-Diesel engines. The numerical simulations are carried out with the 3D-CFD code KIVA3V. The use of different water diesel emulsions is investigated and assessed with the numerical model.

Scaling liquid penetration in evaporating sprays for different size diesel engines

2019 ◽  
Vol 21 (9) ◽  
pp. 1662-1677 ◽  
Author(s):  
Xinyi Zhou ◽  
Tie Li ◽  
Yijie Wei ◽  
Ning Wang
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
High Speed ◽  
Scaling Laws ◽  
Fuel Injection ◽  
Pollutant Emissions ◽  
Liquid Penetration ◽  
Spray Characteristics ◽  
Penetration Length ◽  
Air Mixing

Scaled model experiments can greatly reduce the cost, time and energy consumption in diesel engine development, and the similarity of spray characteristics has a primary effect on the overall scaling results of engine performance and pollutant emissions. However, although so far the similarity of spray characteristics under the non-evaporating condition has been studied to some extent, researches on scaling the evaporating sprays are still absent. The maximum liquid penetration length has a close relationship with the spray evaporation processes and is a key parameter in the design of diesel engine spray combustion system. In this article, the similarity of maximum liquid penetration length is theoretically derived based on the hypotheses that the spray evaporation processes in modern high-pressure common rail diesel engines are fuel–air mixing controlled and local interphase transport controlled, respectively. After verifying that the fuel injection rates are perfectly scaled, the similarity of maximum liquid penetration length in evaporating sprays is studied for three scaling laws using two nozzles with hole diameter of 0.11 and 0.14 mm through the high-speed diffused back-illumination method. Under the test conditions of different fuel injection pressures, ambient temperatures and densities, the lift-off law and speed law lead to a slightly increased maximum liquid penetration length, while the pressure law can well scale the maximum liquid penetration length. The experimental results are consistent with the theoretical analyses based on the hypothesis that the spray evaporation processes are fuel–air mixing controlled, indicating that the local interphase transports of energy, momentum and mass on droplet surface are not rate-controlled steps with respect to spray evaporation processes.

A Survey of Analysis, Modeling, and Diagnostics of Diesel Fuel Injection Systems

2016 ◽  
Vol 138 (8) ◽  
Author(s):  
Tomi R. Krogerus ◽  
Mika P. Hyvönen ◽  
Kalevi J. Huhtala
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Power Plants ◽  
Fuel Injection ◽  
High Reliability ◽  
Injection System ◽  
Engine Fuel ◽  
Injection Equipment ◽  
Diesel Fuel Injection

Diesel engines are widely used due to their high reliability, high thermal efficiency, fuel availability, and low consumption. They are used to generate power, e.g., in passenger cars, ships, power plants, marine offshore platforms, and mining and construction machines. The engine is at heart of these applications, so keeping it in good working condition is vital. Recent technical and computational advances and environmental legislation have stimulated the development of more efficient and robust techniques for the diagnostics of diesel engines. The emphasis is on the diagnostics of faults under development and the causes of engine failure or reduced efficiency. Diesel engine fuel injection plays an important role in the development of the combustion in the engine cylinder. Arguably, the most influential component of the diesel engine is the fuel injection equipment; even minor faults can cause a major loss of efficiency of the combustion and an increase in engine emissions and noise. With increased sophistication (e.g., higher injection pressures) being required to meet continuously improving noise, exhaust smoke, and gaseous emission regulations, fuel injection equipment is becoming even more susceptible to failure. The injection systems have been shown to be the largest contributing factor in diesel engine failures. Extracting the health information of components in the fuel injection system is a very demanding task. Besides the very time-consuming nature of experimental investigations, direct measurements are also limited to selected observation points. Diesel engine faults normally do not occur in a short timeframe. The modeling of typical engine faults, particularly combustion related faults, in a controlled manner is thus vital for the development of diesel engine diagnostics and fault detection. Simulation models based on physical grounds can enlarge the number of studied variables and also obtain a better understanding of localized phenomena that affect the overall behavior of the system. This paper presents a survey of the analysis, modeling, and diagnostics of diesel fuel injection systems. Typical diesel fuel injection systems and their common faults are presented. The most relevant state of the art research articles on analysis and modeling of fluid injection systems as well as diagnostics techniques and measured signals describing the behavior of the system are reviewed and the results and findings are discussed. The increasing demand and effect of legislation related to diagnostics, especially on-board diagnostics (OBD), are discussed with reference to the future progress of this field.

scholarly journals Cavitation in the fuel injection system of diesel engines.

1989 ◽  
Vol 55 (512) ◽  
pp. 944-950 ◽  
Author(s):  
Hisashi WATANABE ◽  
Masatoshi YAMADA ◽  
Kenji IMAI ◽  
Yoshiya ISHII ◽  
Shinobu SASAKI
Keyword(s):  
Diesel Engines ◽  
Fuel Injection ◽  
Injection System ◽  
Fuel Injection System
Sign in / Sign up

Export Citation Format

Share Document