Simulating the Air Bearing Pressure and Flying Height in a Humid Environment

2007 ◽  
Vol 130 (1) ◽  
Author(s):  
Shuyu Zhang ◽  
Brian Strom ◽  
Sung-Chang Lee ◽  
George Tyndall
Keyword(s):  
Hard Disk Drives ◽  
Hard Disk ◽  
Disk Drive ◽  
Flying Height ◽  
Test Cases ◽  
Air Bearing ◽  
Disk Drives ◽  
Humid Environment ◽  
Flying Attitude ◽  
Saturation Vapor

For a hard disk drive operating in a humid environment, the water vapor in the slider’s air bearing is typically compressed beyond its saturation vapor pressure, causing the vapor to condense. Consequently, the air bearing pressure decreases and the slider’s flying attitude adjusts to balance the forces from the suspension. A method for calculating this air bearing response to humid air is presented. Using two air bearing designs, several test cases are analyzed to illustrate the air bearing response for various temperatures and humidity levels. The calculated flying heights agree with those measured in commercial hard disk drives.

Simulating the Air Bearing Flying Height in a Humid Environment

2007 ◽  
Author(s):  
Shuyu Zhang ◽  
Brian Strom ◽  
Sungchang Lee ◽  
George Tyndall
Keyword(s):  
Hard Disk Drives ◽  
Hard Disk ◽  
Disk Drive ◽  
Flying Height ◽  
Test Cases ◽  
Air Bearing ◽  
Humid Environment ◽  
Bearing Design ◽  
Flying Attitude ◽  
Saturation Vapor

For a hard disk drive operating in a humid environment, the water vapor in the slider’s air bearing is typically compressed beyond its saturation vapor pressure, causing the vapor to condense. Consequently, the air bearing pressure decreases and the slider’s flying attitude adjusts to balance the forces from the suspension. A method for calculating this air bearing response to humid air is presented. Using one particular air bearing design as an example, several test cases are analyzed to illustrate the air bearing response for various temperatures and humidity levels. The calculated flying heights agree with those measured in commercial hard disk drives.

Design and Dynamics of Flying Height Control Slider With Piezoelectric Nanoactuator in Hard Disk Drives

2006 ◽  
Vol 129 (1) ◽  
pp. 161-170 ◽  
Author(s):  
Jia-Yang Juang ◽  
David B. Bogy ◽  
C. Singh Bhatia
Keyword(s):  
Numerical Study ◽  
Hard Disk Drives ◽  
Hard Disk ◽  
Areal Density ◽  
Flying Height ◽  
Air Bearing ◽  
Disk Drives ◽  
Adhesion Forces ◽  
Surface Design ◽  
Ultrahigh Density

To achieve the areal density goal in hard disk drives of 1Tbit∕in.2 the minimum physical spacing or flying height (FH) between the read/write element and disk must be reduced to ∼2nm. A brief review of several FH adjustment schemes is first presented and discussed. Previous research showed that the actuation efficiency (defined as the ratio of the FH reduction to the stroke) was low due to the significant air bearing coupling. In this paper, an air bearing surface design, Slider B, for a FH control slider with a piezoelectric nanoactuator is proposed to achieve virtually 100% efficiency and to increase dynamics stability by minimizing the nanoscale adhesion forces. A numerical study was conducted to investigate both the static and dynamic performances of the Slider B, such as uniformity of gap FH with near-zero roll over the entire disk, ultrahigh roll stiffness and damping, low nanoscale adhesion forces, uniform FH track-seeking motion, dynamic load/unload, and FH modulation. Slider B was found to exhibit an overall enhancement in performance, stability, and reliability in ultrahigh density magnetic recording.

Air Bearing Pushback in Heat Assisted Magnetic Recording

2019 ◽  
Author(s):  
Shaomin Xiong ◽  
Robert Smith ◽  
Chanh Nguyen ◽  
Youfeng Zhang ◽  
Yeoungchin Yoon
Keyword(s):  
Magnetic Recording ◽  
Hard Disk Drives ◽  
Hard Disk ◽  
Disk Drive ◽  
Flying Height ◽  
Air Bearing ◽  
Magnetic Media ◽  
Heat Assisted Magnetic Recording ◽  
Height Control ◽  
Different Dimensions

Abstract The air bearing surface is critical to the spacing control in current hard disk drives (HDDs). Thermal protrusions, including thermal flying height control (TFC) and writer coil protrusion, drive the reader/writer elements closer to the magnetic media. The spacing control actuation efficiency depends on the air bearing push back response after the TFC or writer protrudes. In the next generation hard disk drive technology, heat assisted magnetic recording (HAMR), laser induced protrusions further complicate the spacing control. The laser induced protrusions, such as the localized NFT protrusion and a wider change of the crown and camber, have very different dimensions and transient characteristics than the traditional TFC and writer protrusion. The dimension of the NFT protrusion is relatively smaller, and the transient is much faster than the TFC protrusion. However, it is found that the NFT protrusion is large enough to generate an air bearing push back effect, which changes the read and write spacing when the laser is powered on. To accurately control spacing in HAMR, this push back effect has to be taken into account.

An Efficient FE Analysis for Complex Low Flying Air-Bearing Slider Designs in Hard Disk Drives—Part I: Static Solution

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
Puneet Bhargava ◽  
David B. Bogy
Keyword(s):  
Hard Disk Drives ◽  
Hard Disk ◽  
Static Solution ◽  
Flying Height ◽  
Air Bearing ◽  
Pressure Gradients ◽  
Disk Drives ◽  
Bearing Stiffness ◽  
Novel Method ◽  
Mesh Refinements

Prediction of the steady state flying height and attitude of air-bearing sliders in hard disk drives via simulations is the basis of their design process. Over the past few years air-bearing surfaces have become increasingly complex incorporating deep etches and steep wall profiles. In this paper we present a novel method of solving the inverse problem for air-bearing sliders in hard disk drives that works well for such new designs. We also present a new method for calculating the static air-bearing stiffness by solving three linear systems of equations. The formulation is implemented, and convergence studies are carried out for the method. Mesh refinements based on flux jumps and pressure gradients are found to work better than those based on other criteria.

Analysis of Thermal Flying-Height Control System About Humid Air Condition in Hard Disk Drive

2014 ◽  
Author(s):  
Jonghak Choi ◽  
No-Cheol Park ◽  
Young-Pil Park ◽  
Kyoung-Su Park ◽  
Eo-Jin Hong ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Disk Drive ◽  
Flying Height ◽  
Air Bearing ◽  
Saturation Vapor Pressure ◽  
Humid Air ◽  
Height Control ◽  
Flying Attitude ◽  
Saturation Vapor

This research investigates to analyze the effect of humid air on TFC system. Required parameters of humid air and flying attitude of slider are calculated. Condensation of air bearing at over the saturation vapor pressure is considered. Heat transfer coefficient for humid air condition is calculated. TFC simulation about humid air is conducted.

Optimization of Air Bearing Slider Design

2005 ◽  
Author(s):  
Wending Fang ◽  
Yujuan Wang ◽  
Yunfei Chen
Keyword(s):  
Simulated Annealing ◽  
Simulated Annealing Algorithm ◽  
Optimal Algorithm ◽  
Hard Disk Drives ◽  
Hard Disk ◽  
Flying Height ◽  
Air Bearing ◽  
Disk Drives ◽  
Slider Air Bearing ◽  
Bearing Design

Hard disk drives continue to increase the data storage density. The parameters of the head slider flying attitude must satisfy very strict performance goals. This paper focuses on the topic of the simulated annealing algorithm when it is applied to the problem of slider air bearing design in hard disk drives. The objective is to minimize the static flying height, to keep the pitch angle within a reasonable range, and to minimize the roll angle. The design variables include recess depth and geometry configuration of the slider air bearing surface. A typical tri-pad slider was taken as the physical model to demonstrate the validity of the optimal algorithm. Results show that simulated annealing is efficient for the optimization of the slider air bearing design. The static air bearing characteristics were enhanced significantly.

scholarly journals Design and Implementation of Dual-Stage Track-Following Control for Hard Disk Drives

2009 ◽  
Author(s):  
Jianbin Nie ◽  
Roberto Horowitz
Keyword(s):  
Hard Disk Drives ◽  
Servo System ◽  
Hard Disk ◽  
Disk Drive ◽  
Disk Drives ◽  
Outer Loop ◽  
Servo Systems ◽  
Design And Implementation ◽  
Integral Action ◽  
Dual Stage

This paper discusses the design and implementation of two track-following controllers for dual-stage hard disk drive servo systems. The first controller is designed by combining an outer loop sensitivity-decoupling (SD) controller with an inner loop disturbance observer (DOB). The second is designed by combining mixed H2/H∞ synthesis techniques with an add-on integral action. The designed controllers were implemented and evaluated on a disk drive with a PZT-actuated suspension-based dual-stage servo system. Position error signal (PES) for the servo system was obtained by measuring the slider displacement with an LDV and injecting a simulated track runout.

Air Bearing Slider Simulation and Modeling for Hard Disk Drives with Ultra-Low Flying Heights

2007 ◽  
pp. 314-314
Author(s):  
B. J. Shi ◽  
D. W. Shu ◽  
B. Gu ◽  
M. R. Parlapalli ◽  
C. N. Delia ◽  
...  
Keyword(s):  
Hard Disk Drives ◽  
Hard Disk ◽  
Air Bearing ◽  
Disk Drives ◽  
Simulation And Modeling ◽  
Air Bearing Slider
Sign in / Sign up

Export Citation Format

Share Document