Critical Analysis of the Available Ammonia Horizontal In-Tube Flow Boiling Heat Transfer Correlations for Liquid Overfeed Evaporators

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
N. Ablanque ◽  
J. Rigola ◽  
C. Oliet ◽  
J. Castro
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Flow Boiling ◽  
Critical Examination ◽  
Data Sets ◽  
Transfer Coefficients ◽  
Experimental Database ◽  
Heat Transfer Coefficients ◽  
Tube Type ◽  
Heat Transfer Correlations

The aim of this work is to present a critical examination of both the available experimental data and the performance of the available heat transfer correlations for oil-free ammonia horizontal in-tube boiling at fin-and-tube-type air-to-refrigerant liquid overfeed evaporation conditions. First, a selection and comparison of the experimental database found in the open literature at the mentioned working conditions is presented. Subsequently, after a short description of the most relevant heat transfer correlations, and in accordance with the selected data, a detailed analysis of the performance of each correlation is carried out. Results show an important divergence between the experimental data sets and conclude that the presently available correlations show considerable discrepancies in heat transfer coefficients within the selected conditions.

A New Model for Predicting Flow Boiling Heat Transfer Coefficients in Horizontal Microfin Tubes

2016 ◽  
Author(s):  
Reem Merchant ◽  
Sunil Mehendale
Keyword(s):  
Heat Transfer ◽  
Flow Boiling ◽  
Operating Conditions ◽  
Transfer Coefficients ◽  
Experimental Database ◽  
New Model ◽  
Heat Transfer Coefficients ◽  
New Correlation ◽  
Wide Range ◽  
Microfin Tubes

The objective of the current work is to present a new correlation for predicting heat transfer coefficients (HTCs) for flow boiling in horizontal microfin tubes. Correlations to predict HTCs have been proposed by numerous authors such as Yu et al., Thome et al., Cavallini et al., Yun et al., Chamra and Mago, Wu et al., and other researchers. The correlations proposed are semi-empirical due to the difficulties associated with modeling the physics of flow boiling in microfin tubes. The above correlations are based on smooth tube flow boiling correlations which are modified to capture the effect of the inner grooves in the microfin tubes on the boiling process. In a previous work, it has been demonstrated that no single correlation can reasonably predict the flow boiling HTCs over a wide range of operating conditions and tube geometric parameters (Merchant and Mehendale). A new model has been proposed and validated using an experimental database of 1576 points from published literature. For the full dataset, the new correlation has X30% of 67.3%, compared to Cavallini et al. and Wu et al. with X30% of 44.2% and 40.6% respectively. The performance of the new model for tube diameters less than and greater than 5 mm has also been discussed for halogenated refrigerants and CO2.

Modeling of Multiphase Flow Boiling in Meso-Channels

2007 ◽  
Author(s):  
John D. Schwarzkopf ◽  
Clayton T. Crowe ◽  
Prashanta Dutta
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Flow Boiling ◽  
Saturation Temperature ◽  
Inlet Temperature ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Heat Transfer Coefficients ◽  
Surface Temperatures ◽  
Good Agreement

Modeling two-phase heat transfer coefficients and corresponding surface temperatures can be difficult. In macro flows, the Chen and Bennett model showed good agreement with experimental data from various researchers. This model was derived from the original Chen model and is primarily based on physical properties with some empiricism. The purpose of this paper is to present a method of modifying a macro-boiling model to predict surface temperatures and heat transfer coefficients associated with meso-channel flow boiling and augmented boiling associated with spray cooling in mesochannels. In order to validate the model, experimental data was gathered. The spray module consisted of 17 sloped channels each having an inlet and exit hydraulic diameter of 1.55 mm and 1.17 mm respectively and a plan length of 33 mm. The heat flux was in the range of 11 – 61kW/m2 and the mass flux was 80 kg/m2-s. The quality of fluid (PF5050) ranged from 0 – 75%. The fluid inlet temperature was 29°C and the saturation temperature was 34°C. The modified model shows good agreement with the experimental data with deviations on the order of 10%.

Heat Transfer Characteristics of Flow Boiling of R134a in Uniformly Heated Horizontal Circular Microtubes

2010 ◽  
Author(s):  
Saptarshi Basu ◽  
Sidy Ndao ◽  
Gregory J. Michna ◽  
Yoav Peles ◽  
Michael K. Jensen
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Heat Flux ◽  
Mass Flux ◽  
Flow Boiling ◽  
Saturation Pressure ◽  
Nucleate Boiling ◽  
Vapor Quality ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

An experimental study of two-phase heat transfer coefficients was carried out using R134a in uniformly heated horizontal circular microtubes with diameters of 0.50 mm and 1.60 mm. The effects of mass flux, heat flux, saturation pressure, and vapor quality on heat transfer coefficients were studied. The flow parameters investigated were as follows: exit pressures of 490, 670, 890, and 1160 kPa; mass fluxes of 300–1500 kg/m2s; heat fluxes of 0–350 kW/m2; inlet subcooling of 5, 20, and 40 °C; and exit qualities of 0 to 1.0. The parametric trends presented in the study are consistent with published literature. Heat transfer coefficients increased with increasing heat flux and saturation pressure while they were independent of variations in mass flux. Vapor quality had a negligible influence on heat transfer coefficients. For the conditions studied, the trends indicated that the dominant heat transfer mechanism was nucleate boiling. The experimental data was compared to three microchannel correlations — the Lazarek-Black, the Kandlikar, and the Tran Correlations. None of the correlations predicted the experimental data very well, although they all predicted the correct trend within limits of experimental error.

Comparison of 30 Boiling and Condensation Correlations for Two-Phase Flows in Compact Plate-Fin Heat Exchangers

2017 ◽  
Author(s):  
Wenhai Li ◽  
Ken Alabi ◽  
Foluso Ladeinde
Keyword(s):  
Heat Transfer ◽  
Heat Exchangers ◽  
Flow Boiling ◽  
Transfer Coefficients ◽  
Two Phase Flows ◽  
Two Phase ◽  
Heat Transfer Coefficients ◽  
Heat Exchanger Design ◽  
Micro Channels ◽  
Vertical Tubes

Over the years, empirical correlations have been developed for predicting saturated flow boiling [1–15] and condensation [16–30] heat transfer coefficients inside horizontal/vertical tubes or micro-channels. In the present work, we have examined 30 of these models, and modified many of them for use in compact plate-fin heat exchangers. However, the various correlations, which have been developed for pipes and ducts, have been modified in our work to make them applicable to extended fin surfaces. The various correlations have been used in a low-order, one-dimensional, finite-volume type numerical integration of the flow and heat transfer equations in heat exchangers. The NIST’s REFPROP database [31] is used to account for the large variations in the fluid thermo-physical properties during phase change. The numerical results are compared with Yara’s experimental data [32]. The validity of the various boiling and condensation models for a real plate-fin heat exchanger design is discussed. The results show that some of the modified boiling and condensation correlations can provide acceptable prediction of heat transfer coefficient for two-phase flows in compact plate-fin heat exchangers.

Flow Boiling Heat Transfer, Pressure Drop, and Flow Pattern for CO2 in a 3.5mm Horizontal Smooth Tube

2009 ◽  
Vol 131 (9) ◽  
Author(s):  
Chang Yong Park ◽  
Pega Hrnjak
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Flow Patterns ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Flow Boiling Heat Transfer

Abstract C O 2 flow boiling heat transfer coefficients and pressure drop in a 3.5mm horizontal smooth tube are presented. Also, flow patterns were visualized and studied at adiabatic conditions in a 3mm glass tube located immediately after a heat transfer section. Heat was applied by a secondary fluid through two brass half cylinders to the test section tubes. This research was performed at evaporation temperatures of −15°C and −30°C, mass fluxes of 200kg∕m2s and 400kg∕m2s, and heat flux from 5kW∕m2 to 15kW∕m2 for vapor qualities ranging from 0.1 to 0.8. The CO2 heat transfer coefficients indicated the nucleate boiling dominant heat transfer characteristics such as the strong dependence on heat fluxes at a mass flux of 200kg∕m2s. However, enhanced convective boiling contribution was observed at 400kg∕m2s. Surface conditions for two different tubes were investigated with a profilometer, atomic force microscope, and scanning electron microscope images, and their possible effects on heat transfer are discussed. Pressure drop, measured at adiabatic conditions, increased with the increase of mass flux and quality, and with the decrease of evaporation temperature. The measured heat transfer coefficients and pressure drop were compared with general correlations. Some of these correlations showed relatively good agreements with measured values. Visualized flow patterns were compared with two flow pattern maps and the comparison showed that the flow pattern maps need improvement in the transition regions from intermittent to annular flow.

Flow Boiling in an In-Line Set of Short Narrow Gap Channels

2015 ◽  
Vol 137 (11) ◽  
Author(s):  
D. Janssen ◽  
J. M. Dixon ◽  
S. J. Young ◽  
F. A. Kulacki
Keyword(s):  
Heat Transfer ◽  
Mass Flux ◽  
Flow Boiling ◽  
Coefficient Of Performance ◽  
Narrow Gap ◽  
Transfer Coefficients ◽  
Data Set ◽  
Heat Transfer Fluids ◽  
Heat Transfer Coefficients ◽  
O 10

Heat transfer coefficients in a set of three symmetrically heated narrow gap channels arranged in line are reported at power densities of 1 kW/cm3 and wall heat flux of 3–40 W/cm2. This configuration emulates an electronics system wherein power dissipation can vary across an array of processors, memory chips, or other components. Three pairs of parallel ceramic resistance heaters in a nearly adiabatic housing form the flow passage, and length-to-gap ratios for each pair of heaters are 34 at a gap of 0.36 mm. Novec™ 7200 and 7300 are used as the heat transfer fluids. Nonuniform longitudinal power distributions are designed with the center heater pair at 1.5X and 2X the level of the first and third heater pairs. At all levels of inlet subcooling, single-phase heat transfer dominates over the first two heater pairs, while the third pair exhibits significant increases because of the presence of flow boiling. Reynolds numbers range from 250 to 1200, Weber numbers from 2 to 14, and boiling numbers from O(10−4) to O(10−3). Exit quality can reach 30% in some cases. Overall heat transfer coefficients of 40 kW/m2K are obtained. Pressure drops for both Novec™ heat transfer fluids are approximately equal at a given mass flux, and a high ratio of heat transfer to pumping power (coefficient of performance (COP)) is obtained. With a mass flux of 250 kg/m2s, heater temperatures can exceed 95 °C, which is the acceptable limit of steady operation for contemporary high performance electronics. Thus, an optimal operating point involving power density, power distribution, mass flux, and inlet subcooling is suggested by the data set for this benchmark multiheater configuration.

Single Phase and Flow Boiling Heat Transfer of Water and Ethanol in a Mini-Channel Array

2010 ◽  
Author(s):  
M. W. Alnaser ◽  
K. Spindler ◽  
H. Mu¨ller-Steinhagen
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
High Speed ◽  
Single Phase ◽  
Flow Boiling ◽  
Video Camera ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
High Speed Video Camera

A test rig was constructed to investigate flow boiling in an electrically heated horizontal mini-channel array. The test section is made of copper and consists of twelve parallel mini-channels. The channels are 1 mm deep, 1 mm wide and 250 mm long. The test section is heated from underneath with six cartridge heaters. The channels are covered with a glass plate to allow visual observations of the flow patterns using a high-speed video-camera. The wall temperatures are measured at five positions along the channel axis with two resistance thermometers in a specified distance in heat flow direction. Local heat transfer coefficients are obtained by calculating the local heat flux. The working fluids are deionised water and ethanol. The experiments were performed under near atmospheric pressure (0.94 bar to 1.2 bar absolute). The inlet temperature was kept constant at 20°C. The measurements were taken for three mass fluxes (120; 150; 185 kg/m2s) at heat fluxes from 7 to 375 kW/m2. Heat transfer coefficients are presented for single phase forced convection, subcooled and saturated flow boiling conditions. The heat transfer coefficient increases slightly with rising heat flux for single phase flow. A strong increase is observed in subcooled flow boiling. At high heat flux the heat transfer coefficient decreases slightly with increasing heat flux. The application of ethanol instead of water leads to an increase of the surface temperature. At the same low heat flux flow boiling heat transfer occurs with ethanol, but in the experiments with water single phase heat transfer is still dominant. It is because of the lower specific heat capacity of ethanol compared to water. There is a slight influence of the mass flux in the investigated parameter range. The pictures of a high-speed video-camera are analysed for the two-phase flow-pattern identification.

Study on Forced Convective Heat Transfer of FC-72 in Vertical Small Tubes

2020 ◽  
Vol 12 (6) ◽  
Author(s):  
Yantao Li ◽  
Yulong Ji ◽  
Katsuya Fukuda ◽  
Qiusheng Liu
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Convection Heat Transfer ◽  
Bulk Liquid ◽  
Transfer Coefficients ◽  
Forced Convective Heat Transfer ◽  
Heat Transfer Coefficients ◽  
Convective Heat Transfer Coefficients

Abstract This paper presents an experimental investigation of the forced convective heat transfer of FC-72 in vertical tubes at various velocities, inlet temperatures, and tube sizes. Exponentially escalating heat inputs were supplied to the small tubes with inner diameters of 1, 1.8, and 2.8 mm and effective heated lengths between 30.1 and 50.2 mm. The exponential periods of heat input range from 6.4 to 15.5 s. The experimental data suggest that the convective heat transfer coefficients increase with an increase in flow velocity and µ/µw (refers to the viscosity evaluated at the bulk liquid temperature over the liquid viscosity estimated at the tube inner surface temperature). When tube diameter and the ratio of effective heated length to inner diameter decrease, the convective heat transfer coefficients increase as well. The experimental data were nondimensionalized to explore the effect of Reynolds number (Re) on forced convection heat transfer coefficient. It was found that the Nusselt numbers (Nu) are influenced by the Re for d = 2.8 mm in the same pattern as the conventional correlations. However, the dependences of Nu on Re for d = 1 and 1.8 mm show different trends. It means that the conventional heat transfer correlations are inadequate to predict the forced convective heat transfer in minichannels. The experimental data for tubes with diameters of 1, 1.8, and 2.8 mm were well correlated separately. And, the data agree with the proposed correlations within ±15%.

Sign in / Sign up

Export Citation Format

Share Document