Parallel Computational Algorithms for the Kinematics and Dynamics of Planar and Spatial Parallel Manipulators

1996 ◽  
Vol 118 (1) ◽  
pp. 22-28 ◽  
Author(s):  
C. M. Gosselin
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Inverse Dynamics ◽  
Parallel Manipulators ◽  
Degree Of Freedom ◽  
Kinematic Chains ◽  
Novel Approach ◽  
Judicious Choice ◽  
Six Degree Of Freedom ◽  
Three Degree Of Freedom

This paper introduces a novel approach for the computation of the inverse dynamics of parallel manipulators. It is shown that, for this type of manipulator, the inverse kinematics and the inverse dynamics procedures can be easily parallelized. The result is a closed-form efficient algorithm using n processors, where n is the number of kinematic chains connecting the base to the end-effector. The dynamics computations are based on the Newton-Euler formalism. The parallel algorithm arises from a judicious choice of the coordinate frames attached to each of the legs, which allows the exploitation of the parallel nature of the mechanism itself. Examples of the application of the algorithm to a planar three-degree-of-freedom parallel manipulator and to a spatial six-degree-of-freedom parallel manipulator are presented.

A New Design of a 6-DOF Parallel Robot

1990 ◽  
Vol 2 (4) ◽  
pp. 308-315 ◽  
Author(s):  
François Pierrot ◽  
◽  
Masaru Uchiyama ◽  
Pierre Dauchez ◽  
Alain Fournier ◽  
...  
Keyword(s):  
Inverse Kinematics ◽  
Dynamic Capabilities ◽  
Inverse Dynamics ◽  
Parallel Robot ◽  
Degree Of Freedom ◽  
Mechanical Structure ◽  
Delta Robot ◽  
Good Set ◽  
Six Degree Of Freedom ◽  
Three Degree Of Freedom

This paper presents a six-degree-of-freedom parallel robot which has been recently designed. The design is based on a three-degree-of-freedom parallel robot called DELTA which was designed in Switzerland by EPFL. First, we give equations corresponding to different models of the DELTA robot: forward and inverse kinematics as well as inverse dynamics. An important feature of our method in deriving these models is to use a “good” set of parameters in order to simplify the equations. Then, in an attempt to extend the principle of the DELTA robot mechanical structure to a six-degree-offreedom parallel robot, we propose a new design called HEXA. Equations for kinematics and dynamics of the HEXA robot are presented and show that it has the same dynamic capabilities as the DELTA robot because, like the DELTA robot, it can be built with light-weight materials and easily modeled. Finally, we discuss optimization of the HEXA robot mechanical structure.

Kinematics of a New High-Precision Three-Degree-of-Freedom Parallel Manipulator

2006 ◽  
Vol 129 (3) ◽  
pp. 320-325 ◽  
Author(s):  
Farhad Tahmasebi
Keyword(s):  
Power Dissipation ◽  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
Base Plane ◽  
Degree Polynomial ◽  
Payload Capacity ◽  
Half Angle ◽  
Three Degree Of Freedom ◽  
Direct Kinematics

Closed-form direct and inverse kinematics of a new three-degree-of-freedom (DOF) parallel manipulator with inextensible limbs and base-mounted actuators are presented. The manipulator has higher resolution and precision than the existing three-DOF mechanisms with extensible limbs. Since all of the manipulator actuators are base mounted, higher payload capacity, smaller actuator sizes, and lower power dissipation can be obtained. The manipulator is suitable for alignment applications where only tip, tilt, and piston motions are significant. The direct kinematics of the manipulator is reduced to solving an eighth-degree polynomial in the square of the tangent of the half-angle between one of the limbs and the base plane. Hence, there are at most 16 assembly configurations for the manipulator. In addition, it is shown that the 16 solutions are eight pairs of reflected configurations with respect to the base plane. Numerical examples for the direct and inverse kinematics of the manipulator are also presented.

Parametric Design of a Spherical Eight-Bar Linkage Based on a Spherical Parallel Manipulator

2008 ◽  
Vol 1 (1) ◽  
Author(s):  
Gim Song Soh ◽  
J. Michael McCarthy
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Parametric Design ◽  
Degree Of Freedom ◽  
Kinematics Analysis ◽  
End Effector ◽  
Arbitrary Base ◽  
Three Degree Of Freedom ◽  
Spherical Parallel Manipulator

This paper presents a procedure that determines the dimensions of two constraining links to be added to a three degree-of-freedom spherical parallel manipulator so that it becomes a one degree-of-freedom spherical (8, 10) eight-bar linkage that guides its end-effector through five task poses. The dimensions of the spherical parallel manipulator are unconstrained, which provides the freedom to specify arbitrary base attachment points as well as the opportunity to shape the overall movement of the linkage. Inverse kinematics analysis of the spherical parallel manipulator provides a set of relative poses between all of the links, which are used to formulate the synthesis equations for spherical RR chains connecting any two of these links. The analysis of the resulting spherical eight-bar linkage verifies the movement of the system.

Determination of the Workspace of 6-DOF Parallel Manipulators

1989 ◽  
Author(s):  
C. Gosselin
Keyword(s):  
Parallel Manipulator ◽  
Graphical Representation ◽  
Three Dimensional ◽  
Parallel Manipulators ◽  
Degree Of Freedom ◽  
Geometrical Properties ◽  
Cartesian Space ◽  
Six Degree Of Freedom

Abstract This paper presents an algorithm for the determination of the workspace of parallel manipulators. The method described here, which is based on geometrical properties of the workspace, leads to a simple graphical representation of the regions of the three-dimensional Cartesian space that are attainable by the manipulator with a given orientation of the platform. Moreover, the volume of the workspace can be easily computed by performing an integration on its boundary, which is obtained from the algorithm. Examples are included to illustrate the application of the method to a six-degree-of-freedom fully-parallel manipulator.

Kinematics of a New High Precision Three Degree-of-Freedom Parallel Manipulator

2005 ◽  
Author(s):  
Farhad Tahmasebi
Keyword(s):  
Power Dissipation ◽  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
Base Plane ◽  
Degree Polynomial ◽  
Payload Capacity ◽  
Half Angle ◽  
Three Degree Of Freedom ◽  
Direct Kinematics

Closed-form direct and inverse kinematics of a new three degree-of-freedom (DOF) parallel manipulator with inextensible limbs and base-mounted actuators are presented. The manipulator has higher resolution and precision than the existing three DOF mechanisms with extensible limbs. Since all of the manipulator actuators are base-mounted; higher payload capacity, smaller actuator sizes, and lower power dissipation can be obtained. The manipulator is suitable for alignment applications where only tip, tilt, and piston motions are significant. The direct kinematics of the manipulator is reduced to solving an eighth-degree polynomial in the square of tangent of half-angle between one of the limbs and the base plane. Hence, there are at most sixteen assembly configurations for the manipulator. In addition, it is shown that the sixteen solutions are eight pairs of reflected configurations with respect to the base plane. Numerical examples for the direct and inverse kinematics of the manipulator are also presented.

A New Algorithm for the Determination of the Workspace of Complex Planar Kinematic Chains

1995 ◽  
Author(s):  
Pascal Lê-Huu ◽  
Clément M. Gosselin
Keyword(s):  
Numerical Solution ◽  
Inverse Kinematics ◽  
Degree Of Freedom ◽  
Topological Graph ◽  
Kinematic Chains ◽  
Cartesian Space ◽  
Hybrid Manipulator ◽  
Three Degree Of Freedom ◽  
Two Degree Of Freedom

Abstract A new algorithm for the determination of the workspace of complex planar kinematic chains is presented in this paper. This algorithm is completely general since it can deal with any kind of topological graph and any set of parameters defined in a convention of notation. It uses the numerical solution of the inverse kinematics and is based on a wavefront expansion in the Cartesian space. Three examples are presented here, and lead to a dexterity mapping for two two-degree-of-freedom multi-loop manipulators and a three-degree-of-freedom hybrid manipulator.

scholarly journals A Six Degree of Freedom Epicyclic-Parallel Manipulator

2012 ◽  
Vol 4 (4) ◽  
Author(s):  
Chao Chen ◽  
Thibault Gayral ◽  
Stéphane Caro ◽  
Damien Chablat ◽  
Guillaume Moroz ◽  
...  
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
Kinematics Analysis ◽  
End Effector ◽  
Six Dof ◽  
Six Degree Of Freedom

A new six-dof epicyclic-parallel manipulator with all actuators allocated on the ground is introduced. It is shown that the system has a considerably simple kinematics relationship, with the complete direct and inverse kinematics analysis provided. Further, the first and second links of each leg can be driven independently by two motors. The serial and parallel singularities of the system are determined, with an interesting feature of the system being that the parallel singularity is independent of the position of the end-effector. The workspace of the manipulator is also analyzed with future applications in haptics in mind.

On the Direct Kinematics of Spherical Three-Degree-of-Freedom Parallel Manipulators with a Coplanar Platform

1994 ◽  
Vol 116 (2) ◽  
pp. 587-593 ◽  
Author(s):  
C. M. Gosselin ◽  
J. Sefrioui ◽  
M. J. Richard
Keyword(s):  
Parallel Manipulator ◽  
Minimal Polynomial ◽  
Polynomial Solution ◽  
Parallel Manipulators ◽  
Degree Of Freedom ◽  
Real Solutions ◽  
Revolute Joints ◽  
Three Degree Of Freedom ◽  
Spherical Parallel Manipulator ◽  
Direct Kinematics

This paper presents a polynomial solution to the direct kinematic problem of a class of spherical three-degree-of-freedom parallel manipulators. This class is defined as the set of manipulators for which the axes of the three revolute joints attached to the gripper link are coplanar and symmetrically arranged. It is shown that, for these manipulators, the direct kinematic problem admits a maximum of 8 real solutions. A polynomial of degree 8 is obtained here to support this result and cases for which all the roots of the polynomial lead to real configurations are presented. Finally, the spherical parallel manipulator with collinear actuators, which received some attention in the literature, is also treated and is shown to lead to a minimal polynomial of the same degree. Examples of the application of the method to manipulators of each category are given and solved.

Optimization Design of a Spatial Six-Degree-of-Freedom Parallel Manipulator Based on Genetic Algorithms and Neural Networks

2008 ◽  
Author(s):  
Dan Zhang ◽  
Zhen Gao
Keyword(s):  
Neural Networks ◽  
Genetic Algorithms ◽  
Parallel Manipulator ◽  
Optimization Design ◽  
Optimal Solution ◽  
Parallel Manipulators ◽  
Degree Of Freedom ◽  
Objective Functions ◽  
Kinetostatic Model ◽  
Six Degree Of Freedom

Optimizing the performances of parallel manipulators by adjusting the structure parameters can be a difficult and time-consuming exercise especially when the parameters are multifarious and the objective functions are too complex. Artificial intelligence approaches can be investigated as the effective criteria to address this issue. In this paper, genetic algorithms and artificial neural network are implemented as the intelligent optimization criteria of global stiffness and dexterity for spatial six degree-of-freedom (DOF) parallel manipulator. The objective functions of global stiffness and dexterity are calculated and deduced according to the kinetostatic model. Neural networks are utilized to model the solutions of performance indices. Multi-objective optimization is developed by Pareto-optimal solution. The effectiveness of the proposed methodology is proved by simulation.

scholarly journals Kinematic analysis of the 3-RPS-3-SPR series–parallel manipulator

Robotica ◽  
2018 ◽  
Vol 37 (7) ◽  
pp. 1240-1266 ◽  
Author(s):  
Abhilash Nayak ◽  
Stéphane Caro ◽  
Philippe Wenger
Keyword(s):  
Kinematic Analysis ◽  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
End Effector ◽  
Inverse Kinematics Problem ◽  
Univariate Polynomial ◽  
Six Degree Of Freedom ◽  
Independent Parameters ◽  
Direct Kinematics

SUMMARYThis paper deals with the kinematic analysis and enumeration of singularities of the six degree-of-freedom 3-RPS-3-SPR series–parallel manipulator (S–PM). The characteristic tetrahedron of the S–PM is established, whose degeneracy is bijectively mapped to the serial singularities of the S–PM. Study parametrization is used to determine six independent parameters that characterize the S–PM and the direct kinematics problem is solved by mapping the transformation matrix between the base and the end-effector to a point in ℙ7. The inverse kinematics problem of the 3-RPS-3-SPR S–PM amounts to find the location of three points on three lines. This problem leads to a minimal octic univariate polynomial with four quadratic factors.

Sign in / Sign up

Export Citation Format

Share Document