Numerical Analysis of Three-Dimensional Bjo¨rk–Shiley Valvular Flow in an Aorta

1997 ◽  
Vol 119 (1) ◽  
pp. 45-51 ◽  
Author(s):  
E.-B. Shim ◽  
K.-S. Chang
Keyword(s):  
Shear Stress ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Leading Edge ◽  
Vortical Flow ◽  
Navier Stokes ◽  
Jet Flows ◽  
Computational Results ◽  
Navier Stokes Equations ◽  
Disk Valve

Laminar vortical flow around a fully opened Bjo¨rk–Shiley valve in an aorta is obtained by solving the three-dimensional incompressible Navier–Stokes equations. Used is a noniterative implicit finite-element Navier–Stokes code developed by the authors, which makes use of the well-known finite difference algorithm PISO. The code utilizes segregated formulation and efficient iterative matrix solvers such as PCGS and ICCG. Computational results show that the three-dimensional vortical flow is recirculating with large shear in the sinus region of the valve chamber. Passing through the valve, the flow is split into major upper and lower jet flows. The spiral vortices generated by the disk are advected in the wake and attenuated rapidly downstream by diffusion. It is shown also that the shear stress becomes maximum near the leading edge of the disk valve.

Numerical Simulation of Clocking Effect on Wake Transportation and Interaction in a 1.5-Stage Axial Turbine

2010 ◽  
Author(s):  
Wei Li ◽  
Hua Ouyang ◽  
Zhao-hui Du
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Leading Edge ◽  
Navier Stokes ◽  
Maximum Efficiency ◽  
Suction Surface ◽  
Navier Stokes Equations ◽  
Pressure Surface ◽  
Turbine Efficiency ◽  
Small Influence

To give insight into the clocking effect and its influence on the wake transportation and its interaction, the unsteady three-dimensional flow through a 1.5-stage axial low pressure turbine is simulated numerically using a density-correction based, Reynolds-Averaged Navier-Stokes equations commercial CFD code. The 2nd stator clocking is applied over ten equal tangential positions. The results show that the harmonic blade number ratio is an important factor affecting the clocking effect. The clocking effect has a very small influence on the turbine efficiency in this investigation. The efficiency difference between the maximum and minimum configuration is nearly 0.1%. The maximum efficiency can be achieved when the 1st stator wake enters the 2nd stator passage near blade suction surface and its adjacent wake passes through the 2nd stator passage close to blade pressure surface. The minimum efficiency appears if the 1st stator wake impinges upon the leading edge of the 2nd stator and its adjacent wake of the 1st stator passed through the mid-channel in the 2nd stator.

Aerodynamic and Aeroacoustic Analyses of a Regenerative Blower

2015 ◽  
Author(s):  
Man-Woong Heo ◽  
Tae-Wan Seo ◽  
Chung-Suk Lee ◽  
Kwang-Yong Kim
Keyword(s):  
Shear Stress ◽  
Variational Formulation ◽  
Stokes Equations ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Side Channel ◽  
Leakage Flow ◽  
Navier Stokes Equations ◽  
Unsteady Flow Analysis

This paper presents a parametric study to investigate the aerodynamic and aeroacoustic characteristics of a side channel regenerative blower. Flow analysis in the side channel blower was carried out by solving three-dimensional steady and unsteady Reynolds-averaged Navier-Stokes equations with the shear stress transport turbulence closure. Aeroacoustic analysis was conducted by solving the variational formulation of Lighthill’s analogy on the basis of the aerodynamic sources extracted from the unsteady flow analysis. The height and width of the blade and the angle between inlet and outlet ports were selected as three geometric parameters, and their effects on the aerodynamic and aeroacoustic performances of the blower have been investigated. The results showed that the aerodynamic and aeroacoustic performances were enhanced by decreasing height and width of blade. It was found that angle between inlet and outlet ports significantly influences the aerodynamic and aeroacoustic performances of the blower due to the stripper leakage flow.

Vortical Flow Structure in the Wake of an Estate Car

2015 ◽  
Vol 18 (4) ◽  
pp. 881-900
Author(s):  
Phillip Gwo-Yan Huang ◽  
Tony Wen-Hann Sheu
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Wake Flow ◽  
Vortical Flow ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Bifurcation Phenomenon ◽  
Simulated Surface ◽  
Finite Volume Simulation ◽  
Vortex Systems

AbstractA finite volume simulation of unsteady vortical wake flow behind a square-back estate car is presented. The three-dimensional time-averaged incompressible Navier-Stokes equations are solved together with the Reynolds stress transport equations for turbulence. By virtue of the simulated surface streamlines, the physics of fluid can be extracted using the topological theory. In addition, the simulated topological singular points and lines of separation are plotted on the car surface. The vortical flow motions that developed behind the mirrors, wheels and car body are explored by means of the simulated time evolving vortex corelines. The formation and interaction of the vortex systems in the wake are examined by tracing the instantaneous streamlines in the vicinity of the simulated vortex corelines. The vortex street behind the estate car is also illustrated by the simulated streaklines. Finally the Hopf bifurcation phenomenon is revealed by the time-varying aerodynamic forces on the car.

Three-Dimensional CFD Rotordynamic Analysis of Gas Labyrinth Seals

2001 ◽  
Author(s):  
J. Jeffrey Moore
Keyword(s):  
Shear Stress ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Internal Flow ◽  
Labyrinth Seal ◽  
Bulk Flow ◽  
Navier Stokes ◽  
Labyrinth Seals ◽  
Navier Stokes Equations ◽  
Rotordynamic Forces

Abstract Labyrinth seals are utilized inside turbomachinery to provide non-contacting control of internal leakage. These seals can also play an important role in determining the rotordynamic stability of the machine. Traditional labyrinth seal models are based on bulk-flow assumptions where the fluid is assumed to behave as a rigid body affected by shear stress at the interfaces. To model the labyrinth seal cavity, a single, driven vortex is assumed and relationships for the shear stress and divergence angle of the through flow jet are developed. These models, while efficient to compute, typically show poor prediction for seals with small clearances, high running speed, and high pressure (Childs, 1993). In an effort to improve the prediction of these components, this work utilizes three-dimensional computational fluid dynamics (CFD) to model the labyrinth seal flow path by solving the Reynolds Averaged Navier Stokes equations. Unlike bulk-flow techniques, CFD makes no fundamental assumptions on geometry, shear stress at the walls, as well as internal flow structure. The method allows modeling of any arbitrarily shaped domain including stepped and interlocking labyrinths with straight or angled teeth. When only leakage prediction is required, an axisymmetric model is created. To calculate rotordynamic forces, a full 3D, eccentric model is solved. The results demonstrate improved leakage and rotordynamic prediction over bulk-flow approaches compared to experimental measurements.

Three-Dimensional CFD Rotordynamic Analysis of Gas Labyrinth Seals

2003 ◽  
Vol 125 (4) ◽  
pp. 427-433 ◽  
Author(s):  
J. Jeffrey Moore
Keyword(s):  
Shear Stress ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Internal Flow ◽  
Labyrinth Seal ◽  
Bulk Flow ◽  
Navier Stokes ◽  
Labyrinth Seals ◽  
Navier Stokes Equations ◽  
Rotordynamic Forces

Labyrinth seals are utilized inside turbomachinery to provide noncontacting control of internal leakage. These seals can also play an important role in determining the rotordynamic stability of the machine. Traditional labyrinth seal models are based on bulk-flow assumptions where the fluid is assumed to behave as a rigid body affected by shear stress at the interfaces. To model the labyrinth seal cavity, a single, driven vortex is assumed and relationships for the shear stress and divergence angle of the through flow jet are developed. These models, while efficient to compute, typically show poor prediction for seals with small clearances, high running speed, and high pressure.* In an effort to improve the prediction of these components, this work utilizes three-dimensional computational fluid dynamics (CFD) to model the labyrinth seal flow path by solving the Reynolds Averaged Navier Stokes equations. Unlike bulk-flow techniques, CFD makes no fundamental assumptions on geometry, shear stress at the walls, as well as internal flow structure. The method allows modeling of any arbitrarily shaped domain including stepped and interlocking labyrinths with straight or angled teeth. When only leakage prediction is required, an axisymmetric model is created. To calculate rotordynamic forces, a full 3D, eccentric model is solved. The results demonstrate improved leakage and rotordynamic prediction over bulk-flow approaches compared to experimental measurements.

Effects of stator splitter blades on aerodynamic performance of a single-stage transonic axial compressor

2020 ◽  
Vol 14 (4) ◽  
pp. 7369-7378
Author(s):  
Ky-Quang Pham ◽  
Xuan-Truong Le ◽  
Cong-Truong Dinh
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Numerical Results ◽  
Single Stage ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Operating Stability ◽  
Length Coverage

Splitter blades located between stator blades in a single-stage axial compressor were proposed and investigated in this work to find their effects on aerodynamic performance and operating stability. Aerodynamic performance of the compressor was evaluated using three-dimensional Reynolds-averaged Navier-Stokes equations using the k-e turbulence model with a scalable wall function. The numerical results for the typical performance parameters without stator splitter blades were validated in comparison with experimental data. The numerical results of a parametric study using four geometric parameters (chord length, coverage angle, height and position) of the stator splitter blades showed that the operational stability of the single-stage axial compressor enhances remarkably using the stator splitter blades. The splitters were effective in suppressing flow separation in the stator domain of the compressor at near-stall condition which affects considerably the aerodynamic performance of the compressor.

scholarly journals Dynamics of Single Droplet Splashing on Liquid Film by Coupling FVM with VOF

Processes ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 841
Author(s):  
Yuzhen Jin ◽  
Huang Zhou ◽  
Linhang Zhu ◽  
Zeqing Li
Keyword(s):  
Liquid Film ◽  
Weber Number ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Single Droplet ◽  
Navier Stokes Equations ◽  
Volume Method ◽  
The Relationship

A three-dimensional numerical study of a single droplet splashing vertically on a liquid film is presented. The numerical method is based on the finite volume method (FVM) of Navier–Stokes equations coupled with the volume of fluid (VOF) method, and the adaptive local mesh refinement technology is adopted. It enables the liquid–gas interface to be tracked more accurately, and to be less computationally expensive. The relationship between the diameter of the free rim, the height of the crown with different numbers of collision Weber, and the thickness of the liquid film is explored. The results indicate that the crown height increases as the Weber number increases, and the diameter of the crown rim is inversely proportional to the collision Weber number. It can also be concluded that the dimensionless height of the crown decreases with the increase in the thickness of the dimensionless liquid film, which has little effect on the diameter of the crown rim during its growth.

The inlet flow structure of a conceptual open-nose supersonic drone

2021 ◽  
pp. 095441002098304
Author(s):  
Eiman B Saheby ◽  
Xing Shen ◽  
Anthony P Hays ◽  
Zhang Jun
Keyword(s):  
Flow Structure ◽  
Stokes Equations ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Computational Fluid Dynamic Simulation ◽  
Navier Stokes ◽  
Ansys Fluent ◽  
Navier Stokes Equations ◽  
Aerodynamic Efficiency ◽  
Performance Effects

This study describes the aerodynamic efficiency of a forebody–inlet configuration and computational investigation of a drone system, capable of sustainable supersonic cruising at Mach 1.60. Because the whole drone configuration is formed around the induction system and the design is highly interrelated to the flow structure of forebody and inlet efficiency, analysis of this section and understanding its flow pattern is necessary before any progress in design phases. The compression surface is designed analytically using oblique shock patterns, which results in a low drag forebody. To study the concept, two inlet–forebody geometries are considered for Computational Fluid Dynamic simulation using ANSYS Fluent code. The supersonic and subsonic performance, effects of angle of attack, sideslip, and duct geometries on the propulsive efficiency of the concept are studied by solving the three-dimensional Navier–Stokes equations in structured cell domains. Comparing the results with the available data from other sources indicates that the aerodynamic efficiency of the concept is acceptable at supersonic and transonic regimes.

Sign in / Sign up

Export Citation Format

Share Document