scholarly journals Closure to “Discussion of ‘Initial Post-buckling Behavior of Thick Rings Under Uniform External Hydrostatic Pressure’” (1996, ASME J. Appl. Mech., 63, p. 560)

1996 ◽  
Vol 63 (2) ◽  
pp. 560-560
Author(s):  
Lei Fu ◽  
A. M. Waas
Keyword(s):  
Hydrostatic Pressure ◽  
External Hydrostatic Pressure ◽  
Buckling Behavior ◽  
Post Buckling

Initial Post-buckling Behavior of Thick Rings Under Uniform External Hydrostatic Pressure

1995 ◽  
Vol 62 (2) ◽  
pp. 338-345 ◽  
Author(s):  
Lei Fu ◽  
A. M. Waas
Keyword(s):  
Hydrostatic Pressure ◽  
Shear Deformation ◽  
Buckling Load ◽  
Deformation Analysis ◽  
Two Dimensional ◽  
Composite Ring ◽  
Buckling Behavior ◽  
Buckling Stability ◽  
Post Buckling ◽  
Beam Type

The initial post-buckling behavior of thick rings under external uniform hydrostatic pressure is investigated. In the analysis, no assumptions are placed upon the relative magnitudes of the elongations and rotations, and the ring is assumed to be elastic and extensional. The importance of including certain nonlinear terms in the initial post-buckling stability analysis and the effects of nonzero shearing strains on the buckling load and the initial post-buckling stability are examined. It is shown that the classical Kirchhoff assumptions, when employed for a ring lead to nonvanishing through thickness strains, εzz and εzθ, with the latter being proportional to the through thickness coordinate z. An approximate first order shear deformation analysis and a two-dimensional elasticity analysis (without beam-type kinematical assumptions) of the initial post-buckling behavior of thick rings are presented and the thickness effects on the buckling load and the initial post-buckling behavior are examined. The formulation for the composite ring was reduced to that of an isotropic ring and the results thus obtained were compared with published one-dimensional results in the literature. It is found from both the shear deformation and the two-dimensional analysis that the initial post-buckling behavior of the isotropic ring and the composite rings studied are stable. The influence of thickness on the degree of stability in the immediate post-buckling response is characterized.

Buckling Behavior of Tire Breaker Structure

1983 ◽  
Vol 11 (1) ◽  
pp. 3-19
Author(s):  
T. Akasaka ◽  
S. Yamazaki ◽  
K. Asano
Keyword(s):  
Elastic Foundation ◽  
Elastic Moduli ◽  
Wave Length ◽  
Bending Moment ◽  
Experimental Results ◽  
Automobile Tire ◽  
Buckling Behavior ◽  
Post Buckling ◽  
Steel Cord ◽  
Interlaminar Shear

Abstract The buckled wave length and the critical in-plane bending moment of laminated long composite strips of cord-reinforced rubber sheets on an elastic foundation is analyzed by Galerkin's method, with consideration of interlaminar shear deformation. An approximate formula for the wave length is given in terms of cord angle, elastic moduli of the constituent rubber and steel cord, and several structural dimensions. The calculated wave length for a 165SR13 automobile tire with steel breakers (belts) was very close to experimental results. An additional study was then conducted on the post-buckling behavior of a laminated biased composite beam on an elastic foundation. This beam is subjected to axial compression. The calculated relationship between the buckled wave rise and the compressive membrane force also agreed well with experimental results.

Appraisal of Allowable Loads by Simplified Rules

1986 ◽  
Vol 108 (2) ◽  
pp. 131-137
Author(s):  
D. Moulin
Keyword(s):  
Experimental Investigation ◽  
Plastic Region ◽  
Thin Structures ◽  
Geometric Imperfections ◽  
Buckling Behavior ◽  
Simplified Method ◽  
Post Buckling ◽  
Initial Geometric Imperfections ◽  
Fast Breeder Reactors ◽  
Breeder Reactors

This paper presents a simplified method to analyze the buckling of thin structures like those of Liquid Metal Fast Breeder Reactors (LMFBR). The method is very similar to those used for the buckling of beams and columns with initial geometric imperfections, buckling in the plastic region. Special attention is paid to the strain hardening of material involved and to possible unstable post-buckling behavior. The analytical method uses elastic calculations and diagrams that account for various initial geometric defects. An application of the method is given. A comparison is made with an experimental investigation concerning a representative LMFBR component.

Study of Ductile-to-Brittle Transition in Single Grit Diamond Scribing of Silicon: Application to Wire Sawing of Silicon Wafers

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
Hao Wu ◽  
Shreyes N. Melkote
Keyword(s):  
Hydrostatic Pressure ◽  
Silicon Wafers ◽  
Depth Of Cut ◽  
Critical Depth ◽  
External Hydrostatic Pressure ◽  
Tensile Stresses ◽  
Brittle Transition ◽  
Ductile Mode Cutting ◽  
Critical Depth Of Cut ◽  
Ductile To Brittle Transition

The ductile-to-brittle cutting mode transition in single grit diamond scribing of monocrystalline silicon is investigated in this paper. Specifically, the effects of scriber tip geometry, coefficient of friction, and external hydrostatic pressure on the critical depth of cut associated with ductile-to-brittle transition and crack generation are studied via an eXtended Finite Element Method (XFEM) based model, which is experimentally validated. Scribers with a large tip radius are shown to produce lower tensile stresses and a larger critical depth of cut compared with scribers with a sharp tip. Spherical tipped scribers are shown to generate only surface cracks, while sharp tipped scribers (conical, Berkovich and Vickers) are found to create large subsurface tensile stresses, which can lead to nucleation of subsurface median/lateral cracks. Lowering the friction coefficient tends to increase the critical depth of cut and hence the extent of ductile mode cutting. The results also show that larger critical depth of cut can be obtained under external hydrostatic pressure. This knowledge is expected to be useful in optimizing the design and application of the diamond coated wire employed in fixed abrasive diamond wire sawing of photovoltaic silicon wafers.

Geometrical Stiffness of Thin-Walled I-Beam Element Based on Rigid-Beam Assemblage Concept

2012 ◽  
Vol 28 (1) ◽  
pp. 97-106 ◽  
Author(s):  
J. D. Yau ◽  
S.-R. Kuo
Keyword(s):  
Stiffness Matrix ◽  
Virtual Work ◽  
Bending Moment ◽  
Beam Element ◽  
Narrow Beam ◽  
Cross Sectional ◽  
Geometric Stiffness ◽  
Buckling Behavior ◽  
Post Buckling ◽  
Thin Walled

ABSTRACTUsing conventional virtual work method to derive geometric stiffness of a thin-walled beam element, researchers usually have to deal with nonlinear strains with high order terms and the induced moments caused by cross sectional stress results under rotations. To simplify the laborious procedure, this study decomposes an I-beam element into three narrow beam components in conjunction with geometrical hypothesis of rigid cross section. Then let us adopt Yanget al.'s simplified geometric stiffness matrix [kg]12×12of a rigid beam element as the basis of geometric stiffness of a narrow beam element. Finally, we can use rigid beam assemblage and stiffness transformation procedure to derivate the geometric stiffness matrix [kg]14×14of an I-beam element, in which two nodal warping deformations are included. From the derived [kg]14×14matrix, it can take into account the nature of various rotational moments, such as semi-tangential (ST) property for St. Venant torque and quasi-tangential (QT) property for both bending moment and warping torque. The applicability of the proposed [kg]14×14matrix to buckling problem and geometric nonlinear analysis of loaded I-shaped beam structures will be verified and compared with the results presented in existing literatures. Moreover, the post-buckling behavior of a centrally-load web-tapered I-beam with warping restraints will be investigated as well.

Sign in / Sign up

Export Citation Format

Share Document