Parameters Affecting the Performance of a Residential-Scale Stationary Fuel Cell System

2006 ◽  
Vol 4 (2) ◽  
pp. 109-115 ◽  
Author(s):  
Mark W. Davis ◽  
A. Hunter Fanney ◽  
Michael J. LaBarre ◽  
Kenneth R. Henderson ◽  
Brian P. Dougherty

Researchers at the National Institute of Standards and Technology have measured the performance of a residential fuel cell system when subjected to various environmental and load conditions. The system, which uses natural gas as its source fuel, is capable of generating electrical power at three nominal power levels (2.5, 4.0, and 5.0kW) while providing thermal energy for user-supplied loads. Testing was conducted to determine the influence of ambient temperature, relative humidity, electrical load, and thermal load on system performance. Steady-state and transient tests were conducted. The steady-state tests were performed in accordance with the American Society of Mechanical Engineering Fuel Cell Power Systems Performance Test Code (PTC-50) for fuel cell power systems. The results of the investigation are being used to develop a proposed rating procedure for residential fuel cell units.

Author(s):  
Mark W. Davis ◽  
A. Hunter Fanney ◽  
Michael J. LaBarre ◽  
Kenneth R. Henderson ◽  
Brian P. Dougherty

Researchers at the National Institute of Standards and Technology (NIST) have measured the performance of a residential fuel cell system when subjected to various environmental and load conditions. The system, which uses natural gas as its source fuel, is capable of generating electrical power at three nominal power levels (2.5 kW, 4.0 kW, and 5.0 kW) while providing thermal energy for user-supplied loads. Testing was conducted to determine the influence of ambient temperature, relative humidity, electrical load, and thermal load on system performance. Steady-state and transient tests were conducted. The steady-state tests were performed in accordance with the American Society of Mechanical Engineering (ASME) Fuel Cell Power Systems Performance Test Code (PTC-50) for fuel cell power systems. The results of the investigation are being used to develop a proposed rating procedure for residential fuel cell units.


Author(s):  
Mark W. Davis ◽  
Michael W. Ellis ◽  
Brian P. Dougherty ◽  
A. Hunter Fanney

The National Institute of Standards and Technology (NIST), in conjunction with Virginia Tech, has developed a rating methodology for residential-scale stationary fuel cell systems. The methodology predicts the cumulative electrical production, thermal energy delivery, and fuel consumption on an annual basis. The annual performance is estimated by representing the entire year of climate and load data into representative winter, spring/fall, and summer days for six different U.S. climatic zones. It prescribes a minimal number of steady state and simulated use tests, which provide the necessary performance data for the calculation procedure that predicts the annual performance. The procedure accounts for the changes in performance resulting from changes in ambient temperature, electrical load, and, if the unit provides thermal as well as electrical power, thermal load. The rating methodology addresses four different types of fuel cell systems: grid-independent electrical load following, grid-connected constant power, grid-connected thermal load following, and grid-connected water heating. This paper will describe a partial validation of the rating methodology for a grid-connected thermal load following fuel cell system. The rating methodology was validated using measured data from tests that subjected the fuel cell system to domestic hot water and space heating thermal loads for each of the three representative days. The simplification of a full year’s load and climate data into three representative days was then validated by comparing the rating methodology predictions with the prediction of each hour over the full year in each of the six cities.


Author(s):  
Neigel Marx ◽  
Daniel Hissel ◽  
Frederic Gustin ◽  
Loic Boulon ◽  
Kodjo Agbossou

Author(s):  
Kaspar Andreas Friedrich ◽  
Josef Kallo ◽  
Johannes Schirmer

Although air transport is responsible for only about 2% of all anthropogenic CO2 emissions, the rapidly increasing volume of air traffic leads to a general concern about the environmental impact of aviation. Future aircraft generations have to face enhanced requirements concerning productivity, environmental compatibility and higher operational availability, thus effecting technical, operational and economical aspects of in-flight and on-ground power generation systems. Today’s development in aircraft architecture undergoes a trend to a “more electric aircraft” which is characterised by a higher proportion of electrical systems substituting hydraulically or pneumatically driven components, and, thus, increasing the amount of electrical power. Fuel cell systems in this context represent a promising solution regarding the enhancement of the energy efficiency for both cruise and ground operations. For several years the Institute of Technical Thermodynamics of the German Aerospace Center (Deutsches Zentrum fu¨r Luft- und Raumfahrt, DLR) in Stuttgart is engaged in the development of fuel cell systems for aircraft applications. The activities of DLR focus on: • Identification of fuel cell applications in aircraft in which the properties of fuel cell systems, namely high electric efficiency, low emissions and silent operation, are capitalized for the aircraft application. • Design and modeling of possible system designs. • Experimental investigations regarding specific aircraft relevant operating conditions. • Qualification of airworthy fuel cell systems. • Set up and full scale testing of fuel cell systems for application in research aircraft. In cooperation with Airbus several fuel cell applications within the aircraft for both ground and cruise operation could be identified. In consequence, fuel cell systems capable to support or even replace existing systems have been derived. In this context, the provision of inert gas for the jet fuel (kerosene) tank and electrical cabin power supply including water regeneration represent the most promising application fields. The contribution will present the state of development discussing the following points: • Modeling of different system architectures and evaluation of promising fuel cell technologies (PEFC vs. SOFC). • Experimental evaluation of fuel cell systems under relevant conditions (low-pressure, vibrations, reformate operation, etc.). • Fuel cell system demonstrator Hyfish (hydrogen powered model aircraft). • Fuel cell test in DLR’s research aircraft ATRA (A320) including the test of an emergency system based on hydrogen and oxygen with 20 kW of electrical power. The fuel cell system was integrated into an A320 aircraft and tested up to a flight altitude of 25 000 feet under several acceleration and inclination conditions.


2001 ◽  
Vol 123 (02) ◽  
pp. 46-51
Author(s):  
Michael Valenti

Manufacturers of fuel cells are working to improve the economics of electrochemical devices to make them more competitive with conventional fossil fuel power systems for industrial plants and vehicles. FuelCell Energy of Danbury, Connecticut, is designing a system to convert polluting coal mine methane into electricity. General Electric MicroGen of Latham, New York, plans to introduce a residential fuel cell system by the end of the year to provide remote homes with backup current and heat. Another residential system is being developed by International Fuel Cells of South Windsor, Connecticut. The Department of Energy’s National Energy Technology Laboratory in Morgantown, West Virginia, is sponsoring a program to determine the feasibility of feeding coal mine methane to fuel cells. The program involves building a 250-kilowatt fuel cell system at the Nelms mining complex operated by Harrison Mining Corp. in Cadiz, Ohio. A fuel cell system planned for the Nelms complex will assist these automotive engines in consuming methane emissions while generating electricity.


Author(s):  
Zhiwen Ma ◽  
Comas Haynes ◽  
Pinakin Patel

Solid oxide fuel cell /gas turbine (SOFC/GT) hybrid power systems have been recognized as having the potential to operate at unprecedented levels of performance (e.g., 50%+ electrical power generation efficiencies with significantly mitigated greenhouse gas, criteria pollutant and noise emissions). Although the emphasis has been upon land applications, there are aeronautical benefits that may be derived as well. Despite these benefits, there have been limited investigations into the technical merit and feasibility of incorporating these hybrid systems onboard aerovehicles. A feasibility investigation has been performed in conjunction with fuel cell system modeling capabilities to conceptually establish auxiliary power system possibilities as well as the viability technology gaps.


2006 ◽  
Vol 4 (4) ◽  
pp. 497-500 ◽  
Author(s):  
Bei-jiann Chang ◽  
Christopher P. Garcia ◽  
Donald W. Johnson ◽  
David J. Bents ◽  
Vincent J. Scullin ◽  
...  

NASA Glenn Research Center (GRC) has recently demonstrated a polymer electrolyte membrane (PEM) based regenerative fuel cell system (RFCS) that operated for five contiguous back-to-back 24h charge/discharge cycles over a period of 120h. The system operated continuously at full rated power with no significant reactant loss, breakdowns, or degradations from June 26 through July 1, 2005. It demonstrated a closed-loop solar energy storage system over repeated day/night cycles that absorbed solar electrical power profiles of 0–15kWe and stored the energy as pressurized hydrogen and oxygen gas in charge mode, then delivered steady 4.5–5kWe electrical power with product water during discharge mode. Fuel cell efficiency, electrolyzer efficiency, as well as system round-trip efficiency were determined. Individual cell performance and the spread of cell voltages within the electrochemical stacks were documented. The amount of waste heat dissipated from the RFCS was also reported. The RFCS demonstrated fully closed-cycle operation without venting or purging, thereby conserving reactant masses involved in the electrochemical processes. Smooth transitions between the fuel cell mode and electrolyzer mode were repeatedly accomplished. The RFCS is applicable to NASA’s lunar and planetary surface solar power needs, providing lightweight energy storage for any multikilowatt-electrical application, where an environmentally sealed system is required.


Author(s):  
Vorachatra Sukwattanajaroon ◽  
Suttichai Assabumrungrat ◽  
Sumittra Charojrochkul ◽  
Navadol Laosiripojana ◽  
Worapon Kiatkittipong

2016 ◽  
Vol 51 (6) ◽  
pp. 778-783 ◽  
Author(s):  
Hiroyuki Murata ◽  
Yasuyoshi Fujii

Sign in / Sign up

Export Citation Format

Share Document