Film Effectiveness Performance of an Arrowhead-Shaped Film-Cooling Hole Geometry

2006 ◽  
Vol 129 (2) ◽  
pp. 331-339 ◽  
Author(s):  
Yoji Okita ◽  
Masakazu Nishiura
Keyword(s):  
Film Cooling ◽  
High Speed ◽  
Large Scale ◽  
Lateral Direction ◽  
Numerical Work ◽  
Pressure Surface ◽  
Pressure Sensitive ◽  
Cooling Hole ◽  
Hole Geometry ◽  
Effectiveness Data

This paper presents the first experimental and numerical work of film effectiveness performance for a novel film-cooling method with an arrowhead-shaped hole geometry. Experimental results demonstrate that the proposed hole geometry improves the film effectiveness on both suction and pressure surface of a generic turbine airfoil. Film effectiveness data for a row of the holes are compared to that of fan-shaped holes at the same inclination angle of 35 deg to the surface on a large-scale airfoil model at engine representative Reynolds number and Mach number in a high-speed tunnel with moderately elevated temperature mainstream flow. The film effectiveness data are collected using pressure-sensitive paint. Numerical results show that the coolant film with the proposed hole geometry remains well attached to the surface and diffuses in the lateral direction in comparison with the conventional laidback fan-shaped holes for coolant to mainstream blowing ratios of 0.6–3.5.

Film Effectiveness Performance of an Arrowhead-Shaped Film Cooling Hole Geometry

2006 ◽  
Author(s):  
Yoji Okita ◽  
Masakazu Nishiura
Keyword(s):  
Film Cooling ◽  
High Speed ◽  
Large Scale ◽  
Lateral Direction ◽  
Numerical Work ◽  
Pressure Surface ◽  
Pressure Sensitive ◽  
Cooling Hole ◽  
Hole Geometry ◽  
Effectiveness Data

This paper presents the first experimental and numerical work of film effectiveness performance for a novel film cooling method with an arrowhead-shaped hole geometry. Experimental results demonstrate that the proposed hole geometry improves the film effectiveness on both suction and pressure surface of a generic turbine airfoil. Film effectiveness data for a row of the holes are compared with that of fan-shaped holes at the same inclination angle of 35° to the surface on a large-scale airfoil model at engine representative Reynolds number and Mach number in a high speed tunnel with moderately elevated temperature mainstream flow. The film effectiveness data are collected using pressure sensitive paint (PSP). Numerical results show that the coolant film with the proposed hole geometry remains well attached to the surface and diffuses in the lateral direction in comparison with the conventional laidback fan-shaped holes for coolant to mainstream blowing ratios of 0.6 to 3.5.

Experimental Investigation Into the Impact of Crossflow on the Coherent Unsteadiness Within Film Cooling Flows

2011 ◽  
Author(s):  
Richard J. Fawcett ◽  
Andrew P. S. Wheeler ◽  
Li He ◽  
Rupert Taylor
Keyword(s):  
Film Cooling ◽  
High Speed ◽  
High Speed Photography ◽  
Cooling Flows ◽  
Pressure Surface ◽  
Cooling Flow ◽  
Cooling Hole ◽  
Crossflow Velocity ◽  
The Impact ◽  
First Time

It is known that the mixing of a film cooling flow with the main turbine passage flow is an unsteady process, with coherent unsteady features occurring across a range of blowing ratios. Upon an aero engine the cooling holes on a turbine blade commonly have a crossflow at the hole inlet. Previous work has shown that crossflow at the hole inlet modifies the time-mean flowfield downstream of a cooling hole compared to the case without crossflow. The current paper investigates the impact of spanwise orientated crossflow on the coherent unsteadiness within film cooling flows. Both cylindrical and fan-shaped holes, located on a blade pressure surface, are studied. The range of blowing ratios considered is 0.7 to 1.8 and the crossflow velocity is up to 0.8 times the bulk jet velocity. High Speed Photography and Hot Wire Anemometry are used to observe the presence of coherent unsteadiness, both immediately downstream of the hole exit and within the cooling hole tube. The results show that the coherent unsteadiness downstream of the hole exit is persistent and its occurrence is not significantly affected by the magnitude of spanwise crossflow. Within the cooling hole tube the existence of coherent unsteadiness is presented for the first time, inside both cylindrical and fan-shaped holes, with a Strouhal number of 0.6 to 0.8. The pattern of this in-hole coherent unsteadiness is seen to change with increasing the crossflow velocity.

Analysis of the Unsteady Flow Field Inside a Fan-Shaped Cooling Hole Predicted by Large-Eddy Simulation

2020 ◽  
Author(s):  
Shubham Agarwal ◽  
Laurent Gicquel ◽  
Florent Duchaine ◽  
Nicolas Odier ◽  
Jérôme Dombard
Keyword(s):  
Film Cooling ◽  
Large Scale ◽  
Fourier Transforms ◽  
Thermal Environment ◽  
Dynamic Mode Decomposition ◽  
Dynamic Mode ◽  
Film Cooling Effectiveness ◽  
Mode Decomposition ◽  
Large Eddy ◽  
Cooling Hole

Abstract Film cooling is a common technique to manage turbine vane and blade thermal environment. Optimizing its cooling efficiency is furthermore an active research topic which goes in hand with a strong knowledge of the flow associated with a cooling hole. The following paper aims at developing deeper understanding of the flow physics associated with a standard cooling hole and helping guide future cooling optimization strategies. For this purpose, Large Eddy Simulations (LES) of the 7-7-7 fan-shaped cooling hole [1] is performed and the flow inside the cooling hole is studied and discussed. Use of mathematical techniques such as the Fast Fourier Transforms (FFT) and Dynamic Mode Decomposition (DMD) is done to quantitatively access the flow modal structure inside the hole based on the LES unsteady predictions. Using these techniques, distinct vortex features inside the cooling hole are captured. These features mainly coincide with the roll-up of the internal shear layer formed at the interface of the separation region at the hole inlet. The topology of these vortex features is discussed in detail and it is also shown how the expansion of the cross-section in case of shaped holes aids in breaking down these vortices. Indeed upon escaping, these large scale features are known to not be always beneficial to film cooling effectiveness.

Bump and Trench Modifications to Film-Cooling Holes at the Vane-Endwall Junction

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
N. Sundaram ◽  
K. A. Thole
Keyword(s):  
Film Cooling ◽  
Large Scale ◽  
Leading Edge ◽  
High Heat ◽  
Junction Region ◽  
High Heat Transfer ◽  
Turbine Vane ◽  
Cooling Hole ◽  
Adiabatic Effectiveness ◽  
Film Cooling Holes

The endwall of a first-stage vane experiences high heat transfer and low adiabatic effectiveness levels because of high turbine operating temperatures and formation of leading edge vortices. These vortices lift the coolant off the endwall and pull the hot mainstream gases toward it. The region of focus for this study is the vane-endwall junction region near the stagnation location where cooling is very difficult. Two different film-cooling hole modifications, namely, trenches and bumps, were evaluated to improve the cooling in the leading edge region. This study uses a large-scale turbine vane cascade with a single row of axial film-cooling holes at the leading edge of the vane endwall. Individual hole trenches and row trenches were placed along the complete row of film-cooling holes. Two-dimensional semi-elliptically shaped bumps were also evaluated by placing the bumps upstream and downstream of the film-cooling row. Tests were carried out for different trench depths and bump heights under varying blowing ratios. The results indicated that a row trench placed along the row of film-cooling holes showed a greater enhancement in adiabatic effectiveness levels when compared to individual hole trenches and bumps. All geometries considered produced an overall improvement to adiabatic effectiveness levels.

Flow Visualisation of a Converging Slot-Hole Film-Cooling Geometry

2002 ◽  
Author(s):  
J. E. Sargison ◽  
S. M. Guo ◽  
M. L. G. Oldfield ◽  
G. D. Lock ◽  
A. J. Rawlinson
Keyword(s):  
Film Cooling ◽  
Momentum Flux ◽  
Large Scale ◽  
Flux Ratio ◽  
Reynolds Numbers ◽  
Flow Visualisation ◽  
Gas Temperature ◽  
Blade Cooling ◽  
Nylon Mesh ◽  
Cooling Hole

This paper presents the first flow visualisation for the previously published novel film cooling hole, the converging slot-hole or console. Published experimental results [4,5] have demonstrated that the console improved both the heat transfer and aerodynamic performance of turbine vane and rotor blade cooling systems. Flow visualisation data for a row of consoles was compared with that of cylindrical and fan-shaped holes and a slot at the same inclination angle of 35° to the surface, on a large-scale, flat-plate model at engine representative Reynolds numbers in a low speed tunnel with ambient temperature mainstream flow. The data were collected using a fine nylon mesh covered with thermochromic liquid crystals, which allowed measurement of gas temperature in planes perpendicular to the flow. The data demonstrated that the console film was similar to a slot film, and remained thin and attached to the surface for coolant to mainstream momentum flux ratios of 1.1 to 40 and for a case with no crossflow (infinite momentum flux ratio).

Bump and Trench Modifications to Film-Cooling Holes at the Vane Endwall Junction

2007 ◽  
Author(s):  
N. Sundaram ◽  
K. A. Thole
Keyword(s):  
Film Cooling ◽  
Large Scale ◽  
Leading Edge ◽  
High Heat ◽  
Junction Region ◽  
High Heat Transfer ◽  
Turbine Vane ◽  
Cooling Hole ◽  
Adiabatic Effectiveness ◽  
Film Cooling Holes

The endwall of a first stage vane experiences high heat transfer and low adiabatic effectiveness levels because of high turbine operating temperatures and formation of leading edge vortices. These vortices lift the coolant off the endwall and pull the hot mainstream gases towards it. The region of focus for this study is the vane-endwall junction region near the stagnation location where cooling is very difficult. Two different film-cooling hole modifications, namely trenches and bumps, were evaluated to improve the cooling in the leading edge region. This study uses a large-scale turbine vane cascade with a single row of axial film-cooling holes at the leading edge of the vane endwall. Individual hole trenches and row trenches were placed along the complete row of film-cooling holes. Two-dimensional semi-elliptically shaped bumps were also evaluated by placing the bumps upstream and downstream of the film-cooling row. Tests were carried out for different trench depths and bump heights under varying blowing ratios. The results indicated that a row trench placed along the row of film-cooling holes showed a greater enhancement in adiabatic effectiveness levels when compared to individual hole trenches and bumps. All geometries considered produced an overall improvement to adiabatic effectiveness levels.

scholarly journals Experimental Investigation of Rotor Tip Film Cooling at an Axial Turbine with Swirling Inflow Using Pressure Sensitive Paint

2019 ◽  
Vol 4 (3) ◽  
pp. 23 ◽  
Author(s):  
Manuel Wilhelm ◽  
Heinz-Peter Schiffer
Keyword(s):  
Film Cooling ◽  
Large Scale ◽  
Density Ratio ◽  
Pressure Sensitive Paint ◽  
Axial Turbine ◽  
Film Cooling Effectiveness ◽  
Pressure Sensitive ◽  
Inlet Swirl ◽  
Blade Tip ◽  
Film Cooling Holes

Rotor tip film cooling is investigated at the Large Scale Turbine Rig, which is a 1.5-stage axial turbine rig operating at low speeds. Using pressure sensitive paint, the film cooling effectiveness η at a squealer-type blade tip with cylindrical pressure-side film cooling holes is obtained. The effect of turbine inlet swirl on η is examined in comparison to an axial inflow baseline case. Coolant-to-mainstream injection ratios are varied between 0.45% and 1.74% for an engine-realistic coolant-to-mainstream density ratio of 1.5. It is shown that inlet swirl causes a reduction in η for low injection ratios by up to 26%, with the trailing edge being especially susceptible to swirl. For injection ratios greater than 0.93%, however, η is increased by up to 11% for swirling inflow, while for axial inflow a further increase in coolant injection does not transfer into a gain in η .

Effects of Surface Deposition, Hole Blockage, and Thermal Barrier Coating Spallation on Vane Endwall Film Cooling

2006 ◽  
Vol 129 (3) ◽  
pp. 599-607 ◽  
Author(s):  
N. Sundaram ◽  
K. A. Thole
Keyword(s):  
Thermal Barrier Coating ◽  
Film Cooling ◽  
Gas Turbines ◽  
Large Scale ◽  
Leading Edge ◽  
Thermal Barrier ◽  
Cooling Effectiveness ◽  
Barrier Coating ◽  
Cooling Hole ◽  
Alternate Fuels

With the increase in usage of gas turbines for power generation and given that natural gas resources continue to be depleted, it has become increasingly important to search for alternate fuels. One source of alternate fuels is coal derived synthetic fuels. Coal derived fuels, however, contain traces of ash and other contaminants that can deposit on vane and turbine surfaces affecting their heat transfer through reduced film cooling. The endwall of a first stage vane is one such region that can be susceptible to depositions from these contaminants. This study uses a large-scale turbine vane cascade in which the following effects on film cooling adiabatic effectiveness were investigated in the endwall region: the effect of near-hole deposition, the effect of partial film cooling hole blockage, and the effect of spallation of a thermal barrier coating. The results indicated that deposits near the hole exit can sometimes improve the cooling effectiveness at the leading edge, but with increased deposition heights the cooling deteriorates. Partial hole blockage studies revealed that the cooling effectiveness deteriorates with increases in the number of blocked holes. Spallation studies showed that for a spalled endwall surface downstream of the leading edge cooling row, cooling effectiveness worsened with an increase in blowing ratio.

scholarly journals Experimental and Numerical Investigation of Sweeping Jet Film Cooling

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Mohammad A. Hossain ◽  
Robin Prenter ◽  
Ryan K. Lundgreen ◽  
Ali Ameri ◽  
James W. Gregory ◽  
...  
Keyword(s):  
Film Cooling ◽  
Thermal Field ◽  
Numerical Study ◽  
Convective Heat Transfer Coefficient ◽  
Density Ratio ◽  
Vortex Pair ◽  
Lateral Direction ◽  
Time Resolved ◽  
Jet In Crossflow ◽  
Cooling Hole

A companion experimental and numerical study was conducted for the performance of a row of five sweeping jet (SJ) film cooling holes consisting of conventional curved fluidic oscillators with an aspect ratio (AR) of unity and a hole spacing of P/D = 8.5. Adiabatic film effectiveness (η), thermal field (θ), convective heat transfer coefficient (h), and discharge coefficient (CD) were measured at two different freestream turbulence levels (Tu = 0.4% and 10.1%) and four blowing ratios (M = 0.98, 1.97, 2.94, and 3.96) at a density ratio of 1.04 and hole Reynolds number of ReD = 2800. Adiabatic film effectiveness and thermal field data were also acquired for a baseline 777-shaped hole. The SJ film cooling hole showed significant improvement in cooling effectiveness in the lateral direction due to the sweeping action of the fluidic oscillator. An unsteady Reynolds-averaged Navier–Stokes (URANS) simulation was performed to evaluate the flow field at the exit of the hole. Time-resolved flow fields revealed two alternating streamwise vortices at all blowing ratios. The sense of rotation of these alternating vortices is opposite to the traditional counter-rotating vortex pair (CRVP) found in a “jet in crossflow” and serves to spread the film coolant laterally.

Film Cooling of Cylindrical Hole With a Downstream Short Crescent-Shaped Block

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Baitao An ◽  
Jianjun Liu ◽  
Chao Zhang ◽  
Sijing Zhou
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Vortex Pair ◽  
Cylindrical Hole ◽  
Test Case ◽  
Main Body ◽  
Lateral Direction ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole

This paper presents a method to improve the film-cooling effectiveness of cylindrical holes. A short crescent-shaped block is placed at the downstream of a cylindrical cooling hole. The block shape is defined by a number of geometric parameters including block height, length and width, etc. The single row hole on a flat plate with inclination angle of 30 deg, pitch ratio of 3, and length-diameter ratio of 6.25 was chosen as the baseline test case. Film-cooling effectiveness for the cylindrical hole with or without the downstream short crescent-shaped block was measured by using the pressure sensitive paint (PSP) technique. The density ratio of coolant (argon) to mainstream air is 1.38. The blowing ratios vary from 0.5 to 1.25. The results showed that the lateral averaged cooling effectiveness is increased remarkably when the downstream block is present. The downstream short block allows the main body of the coolant jet to pass over the block top and to form a new down-wash vortex pair, which increases the coolant spread in the lateral direction. The effects of each geometrical parameter of the block on the film-cooling effectiveness were studied in detail.

Sign in / Sign up

Export Citation Format

Share Document