The Mixed Mode I and II Interface Crack in Piezoelectromagneto–Elastic Anisotropic Bimaterials

2006 ◽  
Vol 74 (4) ◽  
pp. 614-627 ◽  
Author(s):  
R. Li ◽  
G. A. Kardomateas

Taking the electric–magnetic field inside the interface crack into account, the interface crack problem of dissimilar piezoelectromagneto (PEMO)–elastic anisotropic bimaterials under in-plane deformation is investigated. The conditions to decouple the in-plane and anti-plane deformation is presented for PEMO–elastic biaterials with a symmetry plane. Using the extended Stroh’s dislocation theory of two-dimensional space and the analytic continuition principle of complex analysis, the interface crack problem is turned into a nonhomogeneous Hilbert equation in matrix notation. Four possible eigenvalues as well as four eigenvectors for the fundamental solution to the corresponding homogeneous Hilbert equation are found, so are four modes of singularities for the fields around the interface crack tip. These singularities are shown to have forms of r−(1∕2)±iϵ1 and r−(1∕2)±iϵ2, in which the bimaterial constants ϵ1 and ϵ2 are proven to be real numbers for practical dissimilar PEMO–elastic bimaterials. Compared with the solution for the interface crack of dissimilar elastic bimaterials without electro–magnetic properties, two new additional singularities are discovered for the interface crack in the PEMO–elastic bimaterial media. The electric–magnetic field inside the crack is solved by employing the “energy method,” which is based on finding the stationary point of the saddle surface of the energy release rate with respect to the electro–magnetic field inside the crack. Closed form expressions for the extended crack tip stress fields and crack open displacements are formulated, so are some other fracture characteristic parameters, such as the extended stress intensity factors and energy release rate (G) for dissimilar PEMO–elastic bimaterial solids. Finally, fundamental results and some conclusions are presented, which could have applications in the failure of piezoelectro/magneto–elastic devices.

2005 ◽  
Vol 73 (2) ◽  
pp. 220-227 ◽  
Author(s):  
R. Li ◽  
G. A. Kardomateas

The mode III interface crack problem is investigated for dissimilar piezo-electro-magneto-elastic bimaterial media, taking the electro-magnetic field inside the crack into account. Closed form solutions are derived for impermeable and permeable cracks. The conventional singularity of r−1∕2 is found for the fields at the distance r ahead of the interface crack tip. Expressions for extended crack tip stress fields and crack opening displacements (ECODs) are derived explicitly, and so are some fracture parameters, such as extended stress intensity factors (ESIFs) and energy release rate (G) for dissimilar bimaterials. An approach called the “energy method,” finding the stationary point of the saddle surface of energy release rate with respect to the electro-magnetic field inside the crack, is proposed. By this method, the components of the induced electro-magnetic field inside the crack are determined, and the results are in exact agreement with those in the literature if the two constituents of the bimaterial media are identical. The effects from mechanical and electro-magnetic property mismatches, such as differences in the stiffness, electric permittivity and magnetic permeability, between the two constituents of the bimedia on the mode III interface crack propagation are illustrated by numerical simulations. The results show that the applied electric and magnetic loading usually retard the growth of the interface crack and the directions of the combined mechanical, electric, and magnetic loading have a significant influence on the mode III interface crack propagation.


2020 ◽  
Vol 10 (12) ◽  
pp. 4227
Author(s):  
Yali Yang ◽  
Seok Jae Chu ◽  
Wei song Huang ◽  
Hao Chen

The evaluation of energy release rate with angle is still a challenging task in metal crack propagation analysis, especially for the mixed Mode I-II-III loading situation. In this paper, the energy release rate associated with stress intensity factors at an arbitrary angle under mixed mode loadings has been investigated using both a numerical method and theoretical derivation. A relatively simple and precise numerical method was established through a series of spatial-inclined ellipses in Mode I-II and ellipsoids in Mode I-II-III, with different propagation angles computed from simulation. Meanwhile, a theoretical expression of the energy release rate with angle for a crack tip under a I-II-III mixed mode crack was deduced based on the propagation mechanism of the crack tip under the influence of a stress field. It is confirmed that the theoretical expression deduced could provide results as accurately as the present numerical method. The present results were confirmed to be effective and accurate by comparison with experimental data and other literature.


1990 ◽  
Vol 57 (4) ◽  
pp. 887-893 ◽  
Author(s):  
D. J. Mukai ◽  
R. Ballarini ◽  
G. R. Miller

A solution is presented for the problem of a finite length crack branching off the interface between two bonded dissimilar isotropic materials. Results are presented in terms of the ratio of the energy release rate of a branched interface crack to the energy release rate of a straight interface crack with the same total length. It is found that this ratio reaches a maximum when the interface crack branches into the softer material. Longer branches tend to have smaller maximum energy release rate ratio angles indicating that all else being equal, a branch crack will tend to turn back parallel to the interface as it grows.


2014 ◽  
Vol 81 (10) ◽  
Author(s):  
Theocharis Baxevanis ◽  
Chad M. Landis ◽  
Dimitris C. Lagoudas

A finite element analysis of steady-state crack growth in pseudoelastic shape memory alloys under the assumption of adiabatic conditions is carried out for plane strain, mode I loading. The crack is assumed to propagate at a critical level of the crack-tip energy release rate and the fracture toughness is obtained as the ratio of the far-field applied energy release rate to the crack-tip critical value. Results related to the influence of latent heat on the near-tip stress field and fracture toughness are presented for a range of parameters related to thermomechanical coupling. The levels of fracture toughness enhancement, associated with the energy dissipated by the transformed material in the wake of the growing crack, are found to be lower under adiabatic conditions than under isothermal conditions [Baxevanis et al., 2014, J. Appl. Mech., 81, 041005]. Given that in real applications of shape memory alloy (SMA) components the processes are usually not adiabatic, which is the case with the lowest energy dissipation during a cyclic loading–unloading process (hysteresis), it is expected that the actual level of transformation toughening would be higher than the one corresponding to the adiabatic case.


Author(s):  
Piotr Bednarz ◽  
Jaroslaw Szwedowicz

In general engineering practice, crack tip opening displacement (CTOD) is very convenient approach for prediction of the components fracture mechanics (FM) lifetime. FM lifetime calculations are defined very well in industry and the lifetime prediction methods based on the CTOD resolve linear and nonlinear material behavior for monotonic and cyclic responses. The experiments confirm that under plasticity conditions the crack tip blunts for small scale or large scale yielding while, crack flanks open against each other only under elastic conditions. However, the CTOD application requires a very fine mesh in order to predict a crack tip deformation in reliable manner. Therefore, much more engineering work have to be involved in fine FE modeling. The crack tip flank deformation is crucial parameter responsible for reliable prediction of the nonlinear energy release rate, which is obtained from Hutchinson-Rice-Rosengren solution and the Shih rule. In accordance with design guidelines, the nonlinear energy release rate obtained from the CTOD must be evaluated conservatively to meet demands of RAM (Reliability, Availability and Maintainability). By using far crack deformation field, the paper proposes an engineering approach, which predicts the CTOD in a conservative manner under elastic-plastic conditions. This novel method is validated numerically by applying the well-known J-integral approach.


Sign in / Sign up

Export Citation Format

Share Document