Mean and Fluctuating Velocity Characteristics of a Separated Shear Layer Past a Surface Mounted Block

2006 ◽  
Vol 129 (2) ◽  
pp. 200-208 ◽  
Author(s):  
Ü. Özkol ◽  
C. Wark ◽  
D. Fabris
Keyword(s):  
Shear Layer ◽  
Reynolds Stress ◽  
Reynolds Shear Stress ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Reynolds Stresses ◽  
Mean Velocity ◽  
Separated Shear Layer ◽  
Block Height ◽  
High Reynolds

The mean velocity, Reynolds stress, and mean vorticity regions of a separated shear layer over a surface mounted block are investigated by 2D Digital Particle Image Velocimetry (DPIV) for three Reynolds numbers (Rea=500, 1000, and 2500) and two channel-to-block height ratios (H∕a=1.825 and 4.6). The recirculation region’s height and length are determined for the separated shear layer by means of U¯=0 contours. It is observed that the high Reynolds stress regions lay just outside of the U¯=0 contours. The flow visualization and DPIV measurement of vorticity indicate that the differing normalized Reynolds stresses between Rea=500 and 1000 are most probably due to the initiation of the vortex shedding between these two Reynolds numbers while, differences are minimal between Rea=1000 and 2500. A sign change in the Reynolds shear stress distribution of the separated shear layer near the leading edge of the block was recognized for every Reynolds number and channel width.

An experimental investigation of a laminar separation bubble on the leading-edge of a modelled aerofoil for different Reynolds numbers

2015 ◽  
Vol 230 (13) ◽  
pp. 2208-2224 ◽  
Author(s):  
A Samson ◽  
S Sarkar
Keyword(s):  
Reynolds Number ◽  
Shear Layer ◽  
Separation Bubble ◽  
Experimental Studies ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Constant Thickness ◽  
Laminar Separation Bubble ◽  
Laminar Separation ◽  
Separated Shear Layer

This paper describes the dynamics of a laminar separation bubble formed on the semi-circular leading edge of constant thickness aerofoil model. Detailed experimental studies are carried out in a low-speed wind tunnel, where surface pressure and time-averaged velocity in the separated region and as well as in the downstream are presented along with flow field visualisations through PIV for various Reynolds numbers ranging from 25,000 to 75,000 (based on the leading edge diameter). The results illustrate that the separated shear layer is laminar up to 20% of separation length and then the perturbations are amplified in the second half attributing to breakdown and reattachment. The bubble length is highly susceptible to change in Reynolds number and plays an important role in outer layer activities. Further, the transition of a separated shear layer is studied through variation of intermittency factor and comparing with existing correlations available in the literature for attached flow and as well as separated flow. Transition of the separated shear layer occurs through formation of K-H rolls, where the intermittency following spot propagation theory appears valid. The predominant shedding frequency when normalised with respect to the momentum thickness at separation remains almost constant with change in Reynolds number. The relaxation is slow after reattachment and the flow takes about five bubble lengths to approach a canonical layer.

scholarly journals On the structure of the self-sustaining cycle in separating and reattaching flows

2018 ◽  
Vol 857 ◽  
pp. 907-936 ◽  
Author(s):  
A. Cimarelli ◽  
A. Leonforte ◽  
D. Angeli
Keyword(s):  
Shear Layer ◽  
Rectangular Plate ◽  
Large Scale ◽  
Reverse Flow ◽  
Leading Edge ◽  
Streamwise Velocity ◽  
The Self ◽  
Small Scale ◽  
Spectral Evolution ◽  
Mean Velocity

The separating and reattaching flows and the wake of a finite rectangular plate are studied by means of direct numerical simulation data. The large amount of information provided by the numerical approach is exploited here to address the multi-scale features of the flow and to assess the self-sustaining mechanisms that form the basis of the main unsteadinesses of the flows. We first analyse the statistically dominant flow structures by means of three-dimensional spatial correlation functions. The developed flow is found to be statistically dominated by quasi-streamwise vortices and streamwise velocity streaks as a result of flow motions induced by hairpin-like structures. On the other hand, the reverse flow within the separated region is found to be characterized by spanwise vortices. We then study the spectral properties of the flow. Given the strongly inhomogeneous nature of the flow, the spectral analysis has been conducted along two selected streamtraces of the mean velocity field. This approach allows us to study the spectral evolution of the flow along its paths. Two well-separated characteristic scales are identified in the near-wall reverse flow and in the leading-edge shear layer. The first is recognized to represent trains of small-scale structures triggering the leading-edge shear layer, whereas the second is found to be related to a very large-scale phenomenon that embraces the entire flow field. A picture of the self-sustaining mechanisms of the flow is then derived. It is shown that very-large-scale fluctuations of the pressure field alternate between promoting and suppressing the reverse flow within the separation region. Driven by these large-scale dynamics, packages of small-scale motions trigger the leading-edge shear layers, which in turn created them, alternating in the top and bottom sides of the rectangular plate with a relatively long period of inversion, thus closing the self-sustaining cycle.

Large-scale modes of turbulent channel flow: transport and structure

2001 ◽  
Vol 448 ◽  
pp. 53-80 ◽  
Author(s):  
Z. LIU ◽  
R. J. ADRIAN ◽  
T. J. HANRATTY
Keyword(s):  
Shear Stress ◽  
Kinetic Energy ◽  
Shear Layer ◽  
Turbulent Kinetic Energy ◽  
Large Scale ◽  
Reynolds Shear Stress ◽  
Reynolds Numbers ◽  
Upstream Region ◽  
Two Dimensional ◽  
Normal Plane

Turbulent flow in a rectangular channel is investigated to determine the scale and pattern of the eddies that contribute most to the total turbulent kinetic energy and the Reynolds shear stress. Instantaneous, two-dimensional particle image velocimeter measurements in the streamwise-wall-normal plane at Reynolds numbers Reh = 5378 and 29 935 are used to form two-point spatial correlation functions, from which the proper orthogonal modes are determined. Large-scale motions – having length scales of the order of the channel width and represented by a small set of low-order eigenmodes – contain a large fraction of the kinetic energy of the streamwise velocity component and a small fraction of the kinetic energy of the wall-normal velocities. Surprisingly, the set of large-scale modes that contains half of the total turbulent kinetic energy in the channel, also contains two-thirds to three-quarters of the total Reynolds shear stress in the outer region. Thus, it is the large-scale motions, rather than the main turbulent motions, that dominate turbulent transport in all parts of the channel except the buffer layer. Samples of the large-scale structures associated with the dominant eigenfunctions are found by projecting individual realizations onto the dominant modes. In the streamwise wall-normal plane their patterns often consist of an inclined region of second quadrant vectors separated from an upstream region of fourth quadrant vectors by a stagnation point/shear layer. The inclined Q4/shear layer/Q2 region of the largest motions extends beyond the centreline of the channel and lies under a region of fluid that rotates about the spanwise direction. This pattern is very similar to the signature of a hairpin vortex. Reynolds number similarity of the large structures is demonstrated, approximately, by comparing the two-dimensional correlation coefficients and the eigenvalues of the different modes at the two Reynolds numbers.

scholarly journals Particle image velocimetry measurements of induced separation at the leading edge of a plate

2016 ◽  
Vol 804 ◽  
pp. 278-297 ◽  
Author(s):  
J. P. J. Stevenson ◽  
K. P. Nolan ◽  
E. J. Walsh
Keyword(s):  
Particle Image Velocimetry ◽  
Shear Layer ◽  
Particle Image ◽  
Reverse Flow ◽  
Leading Edge ◽  
Quadrant Analysis ◽  
Bypass Transition ◽  
Reynolds Stresses ◽  
Free Stream Turbulence ◽  
Image Velocimetry

The free shear layer that separates from the leading edge of a round-nosed plate has been studied under conditions of low (background) and elevated (grid-generated) free stream turbulence (FST) using high-fidelity particle image velocimetry. Transition occurs after separation in each case, followed by reattachment to the flat surface of the plate downstream. A bubble of reverse flow is thereby formed. First, we find that, under elevated (7 %) FST, the time-mean bubble is almost threefold shorter due to an accelerated transition of the shear layer. Quadrant analysis of the Reynolds stresses reveals the presence of slender, highly coherent fluctuations amid the laminar part of the shear layer that are reminiscent of the boundary-layer streaks seen in bypass transition. Instability and the roll-up of vortices then follow near the crest of the shear layer. These vortices are also present under low FST and in both cases are found to make significant contributions to the production of Reynolds stress over the rear of the bubble. But their role in reattachment, whilst important, is not yet fully clear. Instantaneous flow fields from the low-FST case reveal that the bubble of reverse flow often breaks up into two or more parts, thereby complicating the overall reattachment process. We therefore suggest that the downstream end of the ‘separation isoline’ (the locus of zero absolute streamwise velocity that extends unbroken from the leading edge) be used to define the instantaneous reattachment point. A histogram of this point is found to be bimodal: the upstream peak coincides with the location of roll-up, whereas the downstream mode may suggest a ‘flapping’ motion.

Sting-free measurements on a magnetically supported right circular cylinder aligned with the free stream

2008 ◽  
Vol 596 ◽  
pp. 49-72 ◽  
Author(s):  
HIROSHI HIGUCHI ◽  
HIDEO SAWADA ◽  
HIROYUKI KATO
Keyword(s):  
Circular Cylinder ◽  
Shear Layer ◽  
Free Stream ◽  
Aerodynamic Force ◽  
Cross Flow ◽  
Leading Edge ◽  
Magnetic Suspension ◽  
Recirculation Region ◽  
Mean Velocity ◽  
Wide Range

The flow over cylinders of varying fineness ratio (length to diameter) aligned with the free stream was examined using a magnetic suspension and balance system in order to avoid model support interference. The drag coefficient variation of a right circular cylinder was obtained for a wide range of fineness ratios. Particle image velocimetry (PIV) was used to examine the flow field, particularly the behaviour of the leading-edge separation shear layer and its effect on the wake. Reynolds numbers based on the cylinder diameter ranged from 5×104 to 1.1×105, while the major portion of the experiment was conducted at ReD=1.0×105. For moderately large fineness ratio, the shear layer reattaches with subsequent growth of the boundary layer, whereas over shorter cylinders, the shear layer remains detached. Differences in the wake recirculation region and the immediate wake patterns are clarified in terms of both the mean velocity and turbulent flow fields, including longitudinal vortical structures in the cross-flow plane of the wake. The minimum drag corresponded to the fineness ratio for which the separated shear layer reattached at the trailing edge of the cylinder. The base pressure was obtained with a telemetry technique. Pressure fields and aerodynamic force fluctuations are also discussed.

PIV Measurements in Square Backward-Facing Step

2007 ◽  
Vol 129 (8) ◽  
pp. 984-990 ◽  
Author(s):  
Mika Piirto ◽  
Aku Karvinen ◽  
Hannu Ahlstedt ◽  
Pentti Saarenrinne ◽  
Reijo Karvinen
Keyword(s):  
Shear Stress ◽  
Reynolds Stress ◽  
Reynolds Shear Stress ◽  
Experimental Tests ◽  
Expansion Ratio ◽  
Spanwise Direction ◽  
Duct Flow ◽  
Backward Facing Step ◽  
Mean Velocity ◽  
Stress Profiles

Measurements with both two-dimensional (2D) two-component and three-component stereo particle image velocimetry (PIV) and computation in 2D and three-dimensional (3D) using Reynolds stress turbulence model with commercial code are carried out in a square duct backward-facing step (BFS) in a turbulent water flow at three Reynolds numbers of about 12,000, 21,000, and 55,000 based on the step height h and the inlet streamwise maximum mean velocity U0. The reattachment locations measured at a distance of Δy=0.0322h from the wall are 5.3h, 5.6h, and 5.7h, respectively. The inlet flow condition is fully developed duct flow before the step change with the expansion ratio of 1.2. PIV results show that the mean velocity, root mean square (rms) velocity profiles, and Reynolds shear stress profiles in all the experimental flow cases are almost identical in the separated shear-layer region when they are nondimensionalized by U0. The sidewall effect of the square BFS flow is analyzed by comparing the experimental statistics with direct numerical simulation (DNS) and Reynolds stress model (RSM) data. For this purpose, the simulation is carried out for both 2D BFS and for square BFS having the same geometry in the 3D case as the experimental case at the lowest Reynolds number. A clear difference is observed in rms and Reynolds shear stress profiles between square BFS experimental results and DNS results in 2D channel in the spanwise direction. The spanwise rms velocity difference is about 30%, with experimental tests showing higher values than DNS, while in contrast, turbulence intensities in streamwise and vertical directions show slightly lower values than DNS. However, with the modeling, the turbulence statistical differences between 2D and 3D RSM cases are very modest. The square BFS indicates 0.5h–1.5h smaller reattachment distances than the reattachment lengths of 2D flow cases.

scholarly journals Natural logarithms

2013 ◽  
Vol 718 ◽  
pp. 1-4 ◽  
Author(s):  
B. J. McKeon
Keyword(s):  
Turbulent Flows ◽  
Reynolds Numbers ◽  
Streamwise Velocity ◽  
Wall Turbulence ◽  
Significant Advance ◽  
Mean Velocity ◽  
Velocity Fluctuations ◽  
Logarithmic Scaling ◽  
The Mean ◽  
High Reynolds

AbstractMarusic et al. (J. Fluid Mech., vol. 716, 2013, R3) show the first clear evidence of universal logarithmic scaling emerging naturally (and simultaneously) in the mean velocity and the intensity of the streamwise velocity fluctuations about that mean in canonical turbulent flows near walls. These observations represent a significant advance in understanding of the behaviour of wall turbulence at high Reynolds number, but perhaps the most exciting implication of the experimental results lies in the agreement with the predictions of such scaling from a model introduced by Townsend (J. Fluid Mech., vol. 11, 1961, pp. 97–120), commonly termed the attached eddy hypothesis. The elegantly simple, yet powerful, study by Marusic et al. should spark further investigation of the behaviour of all fluctuating velocity components at high Reynolds numbers and the outstanding predictions of the attached eddy hypothesis.

Time-Resolved Velocity Measurements in a Matched Refractive Index Facility of Randomly Packed Spheres

2018 ◽  
Author(s):  
Ethan Kappes ◽  
Mateusz Marciniak ◽  
Andrew Mills ◽  
Robert Muyshondt ◽  
Stephen King ◽  
...  
Keyword(s):  
Root Mean Square ◽  
Experimental Studies ◽  
Reynolds Numbers ◽  
Index Of Refraction ◽  
Mean Square ◽  
Reynolds Stresses ◽  
Velocity Measurements ◽  
Mean Velocity ◽  
Time Resolved ◽  
Wall Boundary

Complex geometries and randomly connected void spaces within packed beds have hindered efforts to characterize the underlying transport phenomena occurring within. In this communication, we present our experimental studies on a facility of randomly packed spheres that can be a representative of sections within a reactor core in a nuclear power plant. The results of high-fidelity velocity measurements can be seen using Time-Resolved Particle Image Velocimetry (TR-PIV) at the pore scales and near the wall boundary in the Matched Index of Refraction (MIR) facility. The MIR approach allows for a non-invasive analysis of the flow within packed spheres at the microscopic scales with high temporal and spatial resolution. Flow characteristics obtained from the TR-PIV measurements at various Reynolds numbers are presented. The results include the first- and second-order flow statistics, such as mean velocity, root-mean-square fluctuating velocity and Reynolds stresses. Effects of the wall boundary and Reynolds numbers on flow patterns are currently being investigated. Comparisons of the mean velocities, root-mean-square fluctuating velocities, and Reynolds stress components show the increase of flow mixing and turbulent intensities within the gaps between spheres in the packed bed. Sizes of recirculation regions, however, seem to be independent of the increase of Reynolds numbers.

Asymptotic scaling in turbulent pipe flow

2007 ◽  
Vol 365 (1852) ◽  
pp. 771-787 ◽  
Author(s):  
B.J McKeon ◽  
J.F Morrison
Keyword(s):  
Asymptotic Behaviour ◽  
Pipe Flow ◽  
Physical Space ◽  
Reynolds Numbers ◽  
Streamwise Velocity ◽  
Turbulent Pipe Flow ◽  
Inertial Subrange ◽  
Velocity Spectrum ◽  
Mean Velocity ◽  
High Reynolds

The streamwise velocity component in turbulent pipe flow is assessed to determine whether it exhibits asymptotic behaviour that is indicative of high Reynolds numbers. The asymptotic behaviour of both the mean velocity (in the form of the log law) and that of the second moment of the streamwise component of velocity in the outer and overlap regions is consistent with the development of spectral regions which indicate inertial scaling. It is shown that an ‘inertial sublayer’ in physical space may be considered as a spatial analogue of the inertial subrange in the velocity spectrum and such behaviour only appears for Reynolds numbers R + >5×10 3 , approximately, much higher than was generally thought.

A Study on Turbulent Boundary Layers on a Smooth Flat Plate in an Open Channel

2001 ◽  
Vol 123 (2) ◽  
pp. 394-400 ◽  
Author(s):  
Ram Balachandar ◽  
D. Blakely ◽  
M. Tachie ◽  
G. Putz
Keyword(s):  
Flat Plate ◽  
Froude Number ◽  
Boundary Layers ◽  
Open Channel ◽  
Reynolds Numbers ◽  
Turbulent Boundary Layers ◽  
Wall Region ◽  
Mean Velocity ◽  
Number Range ◽  
High Reynolds

An experimental study was undertaken to investigate the characteristics of turbulent boundary layers developing on smooth flat plate in an open channel flow at moderately high Froude numbers (0.25<Fr<1.1) and low momentum thickness Reynolds numbers 800<Reθ<2900. The low range of Reynolds numbers and the high Froude number range make the study important, as most other studies of this type have been conducted at high Reynolds numbers and lower Froude numbers (∼0.1). Velocity measurements were carried out using a laser-Doppler anemometer equipped with a beam expansion device to enable measurements close to the wall region. The shear velocities were computed using the near-wall measurements in the viscous subregion. The variables of interest include the longitudinal mean velocity, the turbulence intensity, and the velocity skewness and flatness distributions across the boundary layer. The applicability of a constant Coles’ wake parameter (Π=0.55) to open channel flows has been discounted. The effect of the Froude number on the above parameters was also examined.

Sign in / Sign up

Export Citation Format

Share Document