Influence of Planetary Needle Bearings on the Performance of Single and Double Pinion Planetary Systems

2006 ◽  
Vol 129 (1) ◽  
pp. 85-94 ◽  
Author(s):  
Avinash Singh
Keyword(s):  
High Stress ◽  
System Level ◽  
Design Parameters ◽  
Major Influence ◽  
Contact Pattern ◽  
Analysis Model ◽  
Planetary Gears ◽  
Aerospace Applications ◽  
Bending Stresses ◽  
Bearing Loads

Planetary gears are widely used in automotive and aerospace applications. Due to demands for greater power density, these gearsets often operate at extremely high stress levels. This has caused system level influences once considered secondary to become critical to the success of planetary gears. One such system level effect that has been largely overlooked is the influence of support structures like planetary needle bearings. There are interactions between the gear distributed loads and the resulting bearing loads and deflections that have implications for both gear and bearing designs. Also, double pinion planetary arrangements are increasingly becoming common. There are still greater interactions between the gear and bearing components in double pinion planetary arrangements. In this paper, we will examine the influence of the bearing deflections (tilt) on the gear load distribution and contact pattern. We will also show the influence of distributed gear loads on the bearing loads (moments) and deflections (tilts). Both, single and double pinion planetary arrangements will be considered. It will be shown that the tilting stiffnesses of the needle bearings have a major influence on gear contact pattern and consequently on contact and bending stresses. It will also be shown that the double pinion planetary arrangement is more likely to result in off-centered loading. Parametric studies will be performed to show the influence of a few design parameters. Theoretical derivations will be validated by numerical simulations. A system level gear analysis model will be used to illustrate the issues involved and quantify the results.

Information Driven Product Development: A Framework for Product Design and Analysis Integration

2007 ◽  
Author(s):  
Angran Xiao
Keyword(s):  
Product Development ◽  
Product Information ◽  
Information Model ◽  
Product Lifecycle Management ◽  
System Level ◽  
Design Parameters ◽  
Analysis Model ◽  
Element Analysis ◽  
Product Information Model ◽  
The Impact

New paradigms and accompanying software systems are necessary to support the integration of system level design and discipline level analysis activities for the implementation of product lifecycle management. In this paper, we present an information driven product development method for the integration in the context of multidisciplinary product realization. The method contains three constituents: product information model which represents the associativities among design requirements, product components, and design parameters; compromise Decision Support Problem which maps the information model directly into design problems; and knowledge based Finite Element Analysis which generates analysis model automatically from the information model. Information driven product development uses product information model as a communication media between design and analysis activities, hence provides an effective way to trace the impact of design changes, facilitates the reuse of analyses models, and supports collaborative decision-making. An electronic chip package design and analysis scenario is presented to illustrate and demonstrate this method.

Design of a Robust Memristive Spiking Neuromorphic System with Unsupervised Learning in Hardware

2021 ◽  
Vol 17 (4) ◽  
pp. 1-26
Author(s):  
Md Musabbir Adnan ◽  
Sagarvarma Sayyaparaju ◽  
Samuel D. Brown ◽  
Mst Shamim Ara Shawkat ◽  
Catherine D. Schuman ◽  
...  
Keyword(s):  
Unsupervised Learning ◽  
Recognition Task ◽  
Single Layer ◽  
Process Variations ◽  
Spike Timing ◽  
System Level ◽  
Design Parameters ◽  
Digital Pulse ◽  
Neuromorphic System ◽  
The Impact

Spiking neural networks (SNN) offer a power efficient, biologically plausible learning paradigm by encoding information into spikes. The discovery of the memristor has accelerated the progress of spiking neuromorphic systems, as the intrinsic plasticity of the device makes it an ideal candidate to mimic a biological synapse. Despite providing a nanoscale form factor, non-volatility, and low-power operation, memristors suffer from device-level non-idealities, which impact system-level performance. To address these issues, this article presents a memristive crossbar-based neuromorphic system using unsupervised learning with twin-memristor synapses, fully digital pulse width modulated spike-timing-dependent plasticity, and homeostasis neurons. The implemented single-layer SNN was applied to a pattern-recognition task of classifying handwritten-digits. The performance of the system was analyzed by varying design parameters such as number of training epochs, neurons, and capacitors. Furthermore, the impact of memristor device non-idealities, such as device-switching mismatch, aging, failure, and process variations, were investigated and the resilience of the proposed system was demonstrated.

scholarly journals Misalignment in Gas Foil Journal Bearings: An Experimental Study

2008 ◽  
Author(s):  
Samuel A. Howard
Keyword(s):  
Journal Bearings ◽  
System Level ◽  
Design Parameters ◽  
Foil Bearing ◽  
Alignment System ◽  
Successful Design ◽  
Shaft Alignment ◽  
Bearing Force ◽  
Management Schemes ◽  
Level Performance

As gas foil journal bearings become more prevalent in production machines, such as small gas turbine propulsion systems and microturbines, system level performance issues must be identified and quantified in order to provide for successful design practices. Several examples of system level design parameters that are not fully understood in foil bearing systems are thermal management schemes, alignment requirements, balance requirements, thrust load balancing, and others. In order to address some of these deficiencies and begin to develop guidelines, this paper presents a preliminary experimental investigation of the misalignment tolerance of gas foil journal bearing systems. Using a notional gas foil bearing supported rotor and a laser-based shaft alignment system, increasing levels of misalignment are imparted to the bearing supports while monitoring temperature at the bearing edges. The amount of misalignment that induces bearing failure is identified and compared to other conventional bearing types such as cylindrical roller bearings and angular contact ball bearings. Additionally, the dynamic response of the rotor indicates that the gas foil bearing force coefficients may be affected by misalignment.

Direct Coupling of a Two-Dimensional Fan Model in a Turbofan Engine Performance Simulation

2016 ◽  
Author(s):  
Ioannis Templalexis ◽  
Alexios Alexiou ◽  
Vassilios Pachidis ◽  
Ioannis Roumeliotis ◽  
Nikolaos Aretakis
Keyword(s):  
Three Dimensional ◽  
Engine Performance ◽  
System Level ◽  
Design Parameters ◽  
High Fidelity ◽  
Two Dimensional ◽  
Performance Simulation ◽  
Cfd Models ◽  
Component Design ◽  
Complex Phenomena

Coupling of high fidelity component calculations with overall engine performance simulations (zooming) can provide more accurate physics and geometry based estimates of component performance. Such a simulation strategy offers the ability to study complex phenomena and their effects on engine performance and enables component design changes to be studied at engine system level. Additionally, component interaction effects can be better captured. Overall, this approach can reduce the need for testing and the engine development time and cost. Different coupling methods and tools have been proposed and developed over the years ranging from integrating the results of the high fidelity code through conventional performance component maps to fully-integrated three-dimensional CFD models. The present paper deals with the direct integration of an in-house two-dimensional (through flow) streamline curvature code (SOCRATES) in a commercial engine performance simulation environment (PROOSIS) with the aim to establish the necessary coupling methodology that will allow future advanced studies to be performed (e.g. engine condition diagnosis, design optimization, mission analysis, distorted flow). A notional two-shaft turbofan model typical for light business jets and trainer aircraft is initially created using components with conventional map-defined performance. Next, a derivative model is produced where the fan component is replaced with one that integrates the high fidelity code. For both cases, an operating line is simulated at sea-level static take-off conditions and their performances are compared. Finally, the versatility of the approach is further demonstrated through a parametric study of various fan design parameters for a better thermodynamic matching with the driving turbine at design point operation.

Split Vibration Modes in Acoustically-Coupled Disk Stacks

1995 ◽  
Author(s):  
Jung-Ge Tseng ◽  
Jonathan Wickert
Keyword(s):  
Natural Frequencies ◽  
Three Dimensional ◽  
System Level ◽  
Thin Plates ◽  
Mode Shapes ◽  
Design Parameters ◽  
Phase System ◽  
Acoustic Coupling ◽  
Annular Plates ◽  
Vibration Model

Abstract Vibration of an array of stacked annular plates, in which adjacent plates couple weakly through an acoustic layer, is investigated through experimental and theoretical methods. Such acoustic coupling manifests itself through split natural frequencies, beating in the time responses of adjacent or separated plates, and system-level modes in which plates in the array vibrate in- or out-of-phase at closely-spaced frequencies. Laboratory measurements, including a technique in which the frequency response function of all in-phase modes but no out-of-phase modes, or visa versa, is measured, demonstrate the contribution of coupling to the natural frequency spectrum, and identify the combinations of design parameters for which it is important. For the lower modes of primary interest here, the natural frequencies of the out-of-phase system modes decrease as the air layer becomes thinner, while those of the in-phase mode remain sensibly constant at the in vacuo values. A vibration model comprising N classical thin plates that couple through the three-dimensional acoustic fields established in the annular cavities between plates is developed, and its results are compared with measurements of the natural frequencies and mode shapes.

Direct Liquid Cooling of High Flux LED Systems: Hot Spot Abatement

2013 ◽  
Author(s):  
Enes Tamdogan ◽  
Mehmet Arik ◽  
M. Baris Dogruoz
Keyword(s):  
Hot Spots ◽  
Hot Spot ◽  
Heat Removal ◽  
Heat Fluxes ◽  
Light Extraction ◽  
Junction Temperature ◽  
System Level ◽  
Design Parameters ◽  
Liquid Cooling ◽  
Wide Range

With the recent advances in wide band gap device technology, solid-state lighting (SSL) has become favorable for many lighting applications due to energy savings, long life, green nature for environment, and exceptional color performance. Light emitting diodes (LED) as SSL devices have recently offered unique advantages for a wide range of commercial and residential applications. However, LED operation is strictly limited by temperature as its preferred chip junction temperature is below 100 °C. This is very similar to advanced electronics components with continuously increasing heat fluxes due to the expanding microprocessor power dissipation coupled with reduction in feature sizes. While in some of the applications standard cooling techniques cannot achieve an effective cooling performance due to physical limitations or poor heat transfer capabilities, development of novel cooling techniques is necessary. The emergence of LED hot spots has also turned attention to the cooling with dielectric liquids intimately in contact with the heat and photon dissipating surfaces, where elevated LED temperatures will adversely affect light extraction and reliability. In the interest of highly effective heat removal from LEDs with direct liquid cooling, the current paper starts with explaining the increasing thermal problems in electronics and also in lighting technologies followed by a brief overview of the state of the art for liquid cooling technologies. Then, attention will be turned into thermal consideration of approximately a 60W replacement LED light engine. A conjugate CFD model is deployed to determine local hot spots and to optimize the thermal resistance by varying multiple design parameters, boundary conditions, and the type of fluid. Detailed system level simulations also point out possible abatement techniques for local hot spots while keeping light extraction at maximum.

Optimal Offloading Configuration of Spread-Moored FPSOs

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
Steven M. Wilkerson ◽  
Satish Nagarajaiah
Keyword(s):  
Environmental Conditions ◽  
Main Tool ◽  
Design Parameters ◽  
Optimization Approach ◽  
Analysis Model ◽  
Simple Analysis ◽  
Formal Approach ◽  
Fine Tune ◽  
Formal Optimization ◽  
Selection Of

As the oil offloading operations of floating production storage and offloading (FPSO) units become more routine, the desire grows to increase the availability for offloading and thus decrease production downtime. Experience with these operations is the main tool available to increase the efficiency of this aspect of deepwater production. However, it is clear that a formal optimization approach can help to fine tune design parameters so that not only is availability increased but the significance of each design parameter can be better understood. The key issue is to define the environmental conditions under which the vessels involved in offloading are able to maintain position. By this, we reduce the notion of availability to a set of operating criteria, which can or cannot be met for a particular set of environmental conditions. The actual operating criteria such as relative vessel heading depend on selection of design parameters, such as the direction and magnitude of external force applied by thrusters or tugs. In the earliest offloading operations, engineering judgment was used to determine the feasibility of offloading at a particular time. For example, if wind and current were not expected to exceed a 1year return period, offloading may be considered safe. This approach can be both conservative and unconservative, depending on the nuances of the particular environmental conditions. This study will propose a formal approach to choosing the design parameters that optimize the availability of a FPSO for offloading. A simple analysis model will be employed so that optimization can be performed quickly using a robust second order method. The proposed analysis model will be compared to model test data to demonstrate its agreement with the more complex system.

Robust Design of Advanced Thermoelectric Conversion Systems: Probabilistic Design Impacts on Specific Power and Power Flux Optimization

2008 ◽  
Vol 1102 ◽  
Author(s):  
Terry J Hendricks ◽  
Naveen K. Karri
Keyword(s):  
System Design ◽  
Thermal Energy ◽  
Integrated System ◽  
System Level ◽  
Specific Power ◽  
Design Parameters ◽  
Probabilistic Design ◽  
Power Flux ◽  
Research Attention ◽  
System Designs

AbstractAdvanced, direct thermal energy conversion technologies are receiving increased research attention in order to recover waste thermal energy in advanced vehicles and industrial processes. Advanced thermoelectric (TE) systems necessarily require integrated system-level analyses to establish accurate optimum system designs. Past system-level design and analysis has relied on well-defined deterministic input parameters even though many critically important environmental and system design parameters in the above mentioned applications are often randomly variable, sometimes according to complex relationships, rather than discrete, well-known deterministic variables. This work describes new research and development creating techniques and capabilities for probabilistic design and analysis of advanced TE power generation systems to quantify the effects of randomly uncertain design inputs in determining more robust optimum TE system designs and expected outputs. Selected case studies involving stochastic TE .material properties demonstrate key stochastic material impacts on power, optimum TE area, specific power, and power flux in the TE design optimization process. Magnitudes and directions of these design modifications are quantified for selected TE system design analysis cases.

scholarly journals Misalignment in Gas Foil Journal Bearings: An Experimental Study

2008 ◽  
Vol 131 (2) ◽  
Author(s):  
Samuel A. Howard
Keyword(s):  
Journal Bearings ◽  
System Level ◽  
Design Parameters ◽  
Foil Bearing ◽  
Alignment System ◽  
Successful Design ◽  
Shaft Alignment ◽  
Bearing Force ◽  
Management Schemes ◽  
Level Performance

As gas foil journal bearings become more prevalent in production machines, such as small gas turbine propulsion systems and microturbines, system level performance issues must be identified and quantified in order to provide for successful design practices. Several examples of system level design parameters that are not fully understood in foil bearing systems are thermal management schemes, alignment requirements, balance requirements, thrust load balancing, and others. In order to address some of these deficiencies and begin to develop guidelines, this paper presents a preliminary experimental investigation of the misalignment tolerance of gas foil journal bearing systems. Using a notional gas foil bearing supported rotor and a laser-based shaft alignment system, increasing levels of misalignment are imparted to the bearing supports while monitoring temperature at the bearing edges. The amount of misalignment that induces bearing failure is identified and compared with other conventional bearing types such as cylindrical roller bearings and angular contact ball bearings. Additionally, the dynamic response of the rotor indicates that the gas foil bearing force coefficients may be affected by misalignment.

Sign in / Sign up

Export Citation Format

Share Document