An Experimental Investigation of Heat Transport Capability in a Nanofluid Oscillating Heat Pipe

2006 ◽  
Vol 128 (11) ◽  
pp. 1213-1216 ◽  
Author(s):  
H. B. Ma ◽  
C. Wilson ◽  
Q. Yu ◽  
K. Park ◽  
U. S. Choi ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Heat Pipe ◽  
Heat Transport ◽  
Working Fluid ◽  
New Approach ◽  
Oscillating Heat Pipe ◽  
Diamond Nanoparticles ◽  
Hplc Grade Water ◽  
Oscillating Motion ◽  
Heat Transport Capability

An experimental investigation of a nanofluid oscillating heat pipe (OHP) was conducted to determine the nanofluid effect on the heat transport capability in an OHP. The nanofluid consisted of HPLC grade water and 1.0vol% diamond nanoparticles of 5-50nm. These diamond nanoparticles settle down in the motionless base fluid. However, the oscillating motion of the OHP suspends the diamond nanoparticles in the working fluid. Experimental results show that the heat transport capability of the OHP significantly increased when it was charged with the nanofluid at a filling ratio of 50%. It was found that the heat transport capability of the OHP depends on the operating temperature. The investigated OHP could reach a thermal resistance of 0.03°C∕W at a heat input of 336W. The nanofluid OHP investigated here provides a new approach in designing a highly efficient next generation of heat pipe cooling devices.

Effect of Al2O3 Microparticles on the Heat Transport Capability in an Oscillating Heat Pipe

2007 ◽  
Author(s):  
Hongtao Gao ◽  
Xiangyang Gao ◽  
Hongbin Ma ◽  
Anjun Jiao
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Volume Ratio ◽  
Working Fluid ◽  
Transport Capacity ◽  
Oscillating Heat Pipe ◽  
Copper Tubing ◽  
Oscillating Motion ◽  
Heat Transport Capability ◽  
Adiabatic Section

An experimental investigation was conducted to determine the microparticle effect on the heat transport capability of an oscillating heat pipe (OHP). The OHP was fabricated from copper tubing with inside diameter of 1.52 mm. The heat pipe consists of the evaporator, adiabatic section, and condenser. When heat load was added to the evaporator of OHP, the strong oscillating motion was generated. Due to the strong oscillation and circulation motions, the heat transport capability of OHP was significantly increased. The experimental results show that there exists an optimum volume ratio of microparticles added into the working fluid. The effects of filling ratio and tilted angle on the heat transport capacity were also conducted.

Experimental Investigation of a Three-Layer Oscillating Heat Pipe

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
C. D. Smoot ◽  
H. B. Ma
Keyword(s):  
Thermal Conductivity ◽  
Experimental Investigation ◽  
Heat Pipe ◽  
Effective Thermal Conductivity ◽  
Heat Transport ◽  
Total Power ◽  
Oscillating Heat Pipe ◽  
Layer Effect ◽  
Layering Effect ◽  
Heat Transport Capability

An experimental investigation of a compact, triple-layer oscillating heat pipe (OHP) has been conducted to determine the channel layer effect on the heat transport capability in an OHP. The OHP has dimensions 13 mm thick, 229 mm long, and 76 mm wide embedded with two-independent closed loops forming three layers of channels. The unique design of the investigated OHP can be readily used to explore the channel layering effect on the heat transport capability in the OHP. The experimental results show that the addition of channel layers can increase the total power and at the same time, it can increase the effective thermal conductivity of the OHP. When the OHP switches from one layer of channels to two layers of channels, the highest effective thermal conductivity can be increased from 5760 W/mK to 26,560 W/mK. At the same time, the dryout limit can be increased. With three layers of channels, the OHP investigated herein can transport a power up to 8 kW with a heat flux level of 103 W/cm2 achieving an effective thermal conductivity of 33,170 W/mK.

High Thermal Conductivity of Diamond Nanofluids and its Effect on the Heat Transport Capability in an Oscillating Heat Pipe

2006 ◽  
Author(s):  
Corey Wilson ◽  
Hongbin Ma ◽  
K. Park
Keyword(s):  
Thermal Conductivity ◽  
Heat Pipe ◽  
Heat Transport ◽  
Pure Water ◽  
Experimental Results ◽  
Liquid Cooling ◽  
Oscillating Heat Pipe ◽  
Diamond Nanoparticles ◽  
Wire Method ◽  
Heat Transport Capability

In heat exchangers and liquid cooling devices the thermal conductivity of the liquid is an important factor in their design. Recently it has been shown that adding small amounts of nanoparticles to the liquid can significantly increase the thermal conductivity of the fluid [1]. This study investigates the thermal conductivity of diamond nanofluid. The nanofluid is HPLC grade water with 1% by volume diamond nanoparticles that are 5-50 nm in diameter. The thermal conductivity was measured by the transient hot-wire method. In order to verify the experimental measurement, the thermal conductivity of pure water (HPLC grade) was conducted and the measurement error is 3.6%. The experimental results show that the diamond nanoparticles can enhance the thermal conductivity of nanofluid. At an ambient temperature of 21 °C, the thermal conductivity for nanofluid was determined to be 1.00 W/m-K comparing with the thermal conductivity of 0.60 W/m-K for pure water (HPLC grade). Therefore, the nanofluid provides a significant increase in thermal conductivity. Utilizing this nanofluid, an oscillating heat pipe was developed and tested. Experimental results showed that when the oscillating heat pipe is charged with diamond nanofluids, the increase in heat transport capability can be significant and highly dependent on the operating temperatures.

Experimental Investigation of Ultrasonic Frequency Effect on an Oscillating Heat Pipe

2016 ◽  
Author(s):  
Nannan Zhao ◽  
Benwei Fu ◽  
Hongbin Ma ◽  
Fengmin Su
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transport ◽  
Frequency Effect ◽  
Ultrasonic Frequency ◽  
Sound Effect ◽  
Oscillating Heat Pipe ◽  
Ultrasonic Sound ◽  
Heat Transfer Capacity ◽  
Heat Transport Capability

The heat transport capability in an oscillating heat pipe (OHP) significantly depends on the oscillating frequency. An external frequency directly affects the natural frequency in the system. In this investigation, the ultrasound sound effect on the heat transport capability in an OHP was conducted with focus on the ultrasonic frequency effect on the oscillating motion and heat transfer capacity in an OHP. The ultrasonic sound was applied to the evaporating section of the OHP by using the electrically-controlled piezoelectric ceramics. The heat pipe was tested with or without the ultrasonic sound with different frequencies. In addition, the effects of operating temperature, heat load from 25 W to 150 W were investigated. The experimental results demonstrate that the heat transfer capacity enhancement of the OHP depends on the frequency of the ultrasound field, and there exists an optimum combination of the frequencies which will lead to the largest enhancement of the heat transfer capacity of the OHP.

Heat Transport Capability in an Oscillating Heat Pipe

2008 ◽  
Vol 130 (8) ◽  
Author(s):  
H. B. Ma ◽  
B. Borgmeyer ◽  
P. Cheng ◽  
Y. Zhang
Keyword(s):  
Heat Transfer ◽  
Mathematical Model ◽  
Experimental Investigation ◽  
Heat Pipe ◽  
Temperature Difference ◽  
Convection Heat Transfer ◽  
Power Input ◽  
Film Condensation ◽  
Oscillating Heat Pipe ◽  
Oscillating Motion

A mathematical model predicting the oscillating motion in an oscillating heat pipe is developed. The model considers the vapor bubble as the gas spring for the oscillating motions including effects of operating temperature, nonlinear vapor bulk modulus, and temperature difference between the evaporator and the condenser. Combining the oscillating motion predicted by the model, a mathematical model predicting the temperature difference between the evaporator and the condenser is developed including the effects of the forced convection heat transfer due to the oscillating motion, the confined evaporating heat transfer in the evaporating section, and the thin film condensation in the condensing section. In order to verify the mathematical model, an experimental investigation was conducted on a copper oscillating heat pipe with eight turns. Experimental results indicate that there exists an onset power input for the excitation of oscillating motions in an oscillating heat pipe, i.e., when the input power or the temperature difference from the evaporating section to the condensing section was higher than this onset value the oscillating motion started, resulting in an enhancement of the heat transfer in the oscillating heat pipe. Results of the combined theoretical and experimental investigation will assist in optimizing the heat transfer performance and provide a better understanding of heat transfer mechanisms occurring in the oscillating heat pipe.

An Experimental Investigation of Three-Dimensional Flat-Plate Oscillating Heat Pipe

2009 ◽  
Author(s):  
Scott M. Thompson ◽  
Hongbin Ma ◽  
Robert A. Winholtz ◽  
Corey Wilson
Keyword(s):  
Experimental Investigation ◽  
Flat Plate ◽  
Heat Pipe ◽  
Three Dimensional ◽  
Neutron Imaging ◽  
Heat Fluxes ◽  
Working Fluid ◽  
Oscillating Heat Pipe ◽  
Oscillatory Pattern ◽  
Thermal Oscillations

An experimental investigation on the effects of condenser temperatures, heating modes and heat inputs on a miniature, three dimensional flat-plate oscillating heat pipe (3D FP-OHP) was conducted visually and thermally. The 3D FP-OHP was charged with acetone at a filling ratio of 0.80, had dimensions of 101.60 × 63.50 × 2.54 mm3, possessed 30 total turns, and had square channels on both sides of the device with a hydraulic diameter of 0.762 mm. Unlike traditional flat-plate designs, this new three-dimensional, compact design allows for multiple heating arrangements and higher heat fluxes. Transient and steady-state temperature measurements were collected at various heat inputs and the activation/start-up was clearly observed for both bottom and side heating modes during reception of its excitation power for this miniature 3D FP-OHP. The neutron imaging technology was simultaneously employed to observe the internal working fluid flow for all tests directly through the heat pipe’s copper wall. The activation was accompanied with a pronounced temperature field relaxation and the onset of chaotic thermal oscillations — all occurring with the same general oscillatory pattern at locations all around the 3D FP-OHP. Qualitative and quantitative analysis of these thermal oscillations, along with the presentation of the average temperature difference and thermal resistance, for all experimental conditions are provided. The novelty of the three-dimensional OHP design is its ability to still produce the oscillating motions of liquid plugs and vapor bubbles and, more importantly, its ability to remove higher heat fluxes.

Improvement of Heat Transfer Performance of Loop Heat Pipe for Electronic Devices

2011 ◽  
Author(s):  
Tomonao Takamatsu ◽  
Katsumi Hisano ◽  
Hideo Iwasaki
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Thermal Energy ◽  
Heat Load ◽  
Cooling System ◽  
Electronic Devices ◽  
Working Fluid ◽  
Loop Heat Pipe ◽  
Reserve Area ◽  
Heat Transport Capability

In this paper is presented the results on performance of the cooling model using Loop Heat Pipe (LHP) system. In recent years, ever-ending demand of high performance CPU led to a rapid increase in the amount of heat dissipation. Consequently, thermal designing of electronic devices need to consider some suitable approach to achieve high cooling performance in limited space. Heat Pipe concept is expected to serve as an effective cooling system for laptop PC, however, it suffered from some problems as follows. The heat transport capability of conventional Heat Pipe decreases with the reduction in its diameter or increase in its length. Therefore, in order to use it as cooling system for future electronic devices, the above-mentioned limitations need to be removed. Because of the operating principle, the LHP system is capable of transferring larger amount of heat than conventional heat pipes. However, most of the LHP systems suffered from some problems like the necessity of installing check valves and reservoirs to avoid occurrence of counter flow. Therefore, we developed a simple LHP system to install it on electronic devices. Under the present experimental condition (the working fluid was water), by keeping the inside diameter of liquid and vapor line equal to 2mm, and the distance between evaporator and condenser equal to 200mm, it was possible to transport more than 85W of thermal energy. The thickness of evaporator was about 5mm although it included a structure to serve the purpose of controlling vapor flow direction inside it. Successful operation of this system at inclined position and its restart capability are confirmed experimentally. In order to make the internal water location visible, the present LHP system is reconstructed using transparent material. In addition, to estimate the limit of heat transport capability of the present LHP system using this thin evaporator, the air cooling system is replaced by liquid cooling one for condensing device. Then this transparent LHP system could transport more than 100W of thermal energy. However, the growth of bubbles in the reserve area with the increase in heat load observed experimentally led to an understanding that in order to achieve stable operation of the LHP system under high heat load condition, it is very much essential to keep enough water in the reserve area and avoid blocking the inlet with bubbles formation.

Sign in / Sign up

Export Citation Format

Share Document