On the Surface Stability of a Spherical Void Embedded in a Stressed Matrix

2005 ◽  
Vol 74 (1) ◽  
pp. 8-12 ◽  
Author(s):  
Jérôme Colin
Keyword(s):  
Growth Rate ◽  
Stability Analysis ◽  
Linear Stability ◽  
Applied Stress ◽  
Spherical Harmonics ◽  
Linear Stability Analysis ◽  
Spherical Cavity ◽  
Spherical Void ◽  
Surface Stability ◽  
Infinitesimal Perturbation

The linear stability analysis of the shape of a spherical cavity embedded in an infinite-size matrix under stress has been performed when infinitesimal perturbation from sphericity of the rod is assumed to appear by surface diffusion. Developing the perturbation on a basis of complete spherical harmonics, the growth rate of each harmonic Ylm(θ,φ) has been determined and the conditions for the development of the different fluctuations have been discussed as a function of the applied stress and the order l of the perturbation.

Variable density and viscosity, miscible displacements in horizontal Hele-Shaw cells. Part 1. Linear stability analysis

2013 ◽  
Vol 721 ◽  
pp. 268-294 ◽  
Author(s):  
L. Talon ◽  
N. Goyal ◽  
E. Meiburg
Keyword(s):  
Growth Rate ◽  
Stability Analysis ◽  
Linear Stability ◽  
Linear Stability Analysis ◽  
Stokes Equations ◽  
Variable Density ◽  
Local Concentration ◽  
Miscible Displacements ◽  
Instability Modes ◽  
Finger Tip

AbstractA computational investigation of variable density and viscosity, miscible displacements in horizontal Hele-Shaw cells is presented. As a first step, two-dimensional base states are obtained by means of simulations of the Stokes equations, which are nonlinear due to the dependence of the viscosity on the local concentration. Here, the vertical position of the displacement front is seen to reach a quasisteady equilibrium value, reflecting a balance between viscous and gravitational forces. These base states allow for two instability modes: first, there is the familiar tip instability driven by the unfavourable viscosity contrast of the displacement, which is modulated by the presence of density variations in the gravitational field; second, a gravitational instability occurs at the unstably stratified horizontal interface along the side of the finger. Both of these instability modes are investigated by means of a linear stability analysis. The gravitational mode along the side of the finger is characterized by a wavelength of about one half to one full gap width. It becomes more unstable as the gravity parameter increases, even though the interface is shifted closer to the wall. The growth rate is largest far behind the finger tip, where the interface is both thicker, and located closer to the wall, than near the finger tip. The competing influences of interface thickness and wall proximity are clarified by means of a parametric stability analysis. The tip instability mode represents a gravity-modulated version of the neutrally buoyant mode. The analysis shows that in the presence of density stratification its growth rate increases, while the dominant wavelength decreases. This overall destabilizing effect of gravity is due to the additional terms appearing in the stability equations, which outweigh the stabilizing effects of gravity onto the base state.

Linear stability analysis of two-way coupled particle-laden density current

2017 ◽  
Vol 95 (3) ◽  
pp. 291-296 ◽  
Author(s):  
Pouriya Amini ◽  
Ehsan Khavasi ◽  
Navid Asadizanjani
Keyword(s):  
Growth Rate ◽  
Stability Analysis ◽  
Linear Stability ◽  
Linear Stability Analysis ◽  
Base Flow ◽  
Interfacial Instability ◽  
Linear Stability Theory ◽  
Flow Density ◽  
Density Current ◽  
Density Currents

Stability of two-way coupled particle-laden density current is studied with the aim of linear stability analysis. Interfacial instability can be found in density currents, which effects entrainment and the rate of effective mixing. In this paper, we investigate the density current interfacial instability using linear stability theory, considering the particles attendance. The ultimate goal is to extract the governing equation for current with particles and study the effect of different parameters on stability of such currents. Base flow has velocity and density profiles of tangent hyperbolic type. Main current and particles are studied in two separate phases. It is found that current will be more stable as M0 (M0 = S∗N∗/ρ∗ where ρ∗ is the non-dimensional flow density, S∗ is the Stokes’ drag coefficient, and N∗ is the particles’ number density) grows, this is a result of number of particles and their radius, and also viscosity effects. The current is more stable as the growth rate increases. As the Richardson number in M0 rises, the growth rate value decreases. As the slope of the river bed increases, the current is less stable.

scholarly journals The Growth and Saturation of Submesoscale Instabilities in the Presence of a Barotropic Jet

2018 ◽  
Vol 48 (11) ◽  
pp. 2779-2797 ◽  
Author(s):  
Megan A. Stamper ◽  
John R. Taylor ◽  
Baylor Fox-Kemper
Keyword(s):  
Growth Rate ◽  
Stability Analysis ◽  
Linear Stability ◽  
Linear Stability Analysis ◽  
Initial Conditions ◽  
Boussinesq Equations ◽  
Small Region ◽  
Computational Domain ◽  
Mean Flow ◽  
The Mean

AbstractMotivated by recent observations of submesoscales in the Southern Ocean, we use nonlinear numerical simulations and a linear stability analysis to examine the influence of a barotropic jet on submesoscale instabilities at an isolated front. Simulations of the nonhydrostatic Boussinesq equations with a strong barotropic jet (approximately matching the observed conditions) show that submesoscale disturbances and strong vertical velocities are confined to a small region near the initial frontal location. In contrast, without a barotropic jet, submesoscale eddies propagate to the edges of the computational domain and smear the mean frontal structure. Several intermediate jet strengths are also considered. A linear stability analysis reveals that the barotropic jet has a modest influence on the growth rate of linear disturbances to the initial conditions, with at most a ~20% reduction in the growth rate of the most unstable mode. On the other hand, a basic state formed by averaging the flow at the end of the simulation with a strong barotropic jet is linearly stable, suggesting that nonlinear processes modify the mean flow and stabilize the front.

Variable-density miscible displacements in a vertical Hele-Shaw cell: linear stability

2007 ◽  
Vol 584 ◽  
pp. 357-372 ◽  
Author(s):  
N. GOYAL ◽  
H. PICHLER ◽  
E. MEIBURG
Keyword(s):  
Growth Rate ◽  
Stability Analysis ◽  
Linear Stability ◽  
Linear Stability Analysis ◽  
Stokes Equations ◽  
Capillary Tube ◽  
Computational Study ◽  
Stability Limit ◽  
Dominant Wavelength ◽  
Miscible Displacements

A computational study based on the Stokes equations is conducted to investigate the effects of gravitational forces on miscible displacements in vertical Hele-Shaw cells. Nonlinear simulations provide the quasi-steady displacement fronts in the gap of the cell, whose stability to spanwise perturbations is subsequently examined by means of a linear stability analysis. The two-dimensional simulations indicate a marked thickening (thinning) and slowing down (speeding up) of the displacement front for flows stabilized (destabilized) by gravity. For the range investigated, the tip velocity is found to vary linearly with the gravity parameter. Strongly stable density stratifications lead to the emergence of flow patterns with spreading fronts, and to the emergence of a secondary needle-shaped finger, similar to earlier observations for capillary tube flows. In order to investigate the transition between viscously driven and purely gravitational instabilities, a comparison is presented between displacement flows and gravity-driven flows without net displacements.The linear stability analysis shows that both the growth rate and the dominant wavenumber depend only weakly on the Péclet number. The growth rate varies strongly with the gravity parameter, so that even a moderately stable density stratification can stabilize the displacement. Both the growth rate and the dominant wavelength increase with the viscosity ratio. For unstable density stratifications, the dominant wavelength is nearly independent of the gravity parameter, while it increases strongly for stable density stratifications. Finally, the kinematic wave theory of Lajeunesse et al. (J. Fluid Mech. vol. 398, 1999, p. 299) is seen to capture the stability limit quite accurately, while the Darcy analysis misses important aspects of the instability.

Thermoacoustic Instability Model With Porous Media: Linear Stability Analysis and the Impact of Porous Media

2018 ◽  
Author(s):  
Cody S. Dowd ◽  
Joseph W. Meadows
Keyword(s):  
Growth Rate ◽  
Porous Media ◽  
Stability Analysis ◽  
Frequency Shift ◽  
Linear Stability ◽  
Linear Stability Analysis ◽  
Growth Rates ◽  
Thermoacoustic Instability ◽  
The Stability ◽  
The Impact

Lean premixed (LPM) combustion systems are susceptible to thermoacoustic instability, which occurs when acoustic pressure oscillations are in phase with the unsteady heat release rates. Porous media has inherent acoustic damping properties, and has been shown to mitigate thermoacoustic instability; however, theoretical models for predicting thermoacoustic instability with porous media do not exist. In the present study, a 1-D model has been developed for the linear stability analysis of the longitudinal modes for a series of constant cross-sectional area ducts with porous media using a n-Tau flame transfer function. By studying the linear regime, the prediction of acoustic growth rates and subsequently the stability of the system is possible. A transfer matrix approach is used to solve for acoustic perturbations of pressure and velocity, stability growth rate, and frequency shift without and with porous media. The Galerkin approximation is used to approximate the stability growth rate and frequency shift, and it is compared to the numerical solution of the governing equations. Porous media is modeled using the following properties: porosity, flow resistivity, effective bulk modulus, and structure factor. The properties of porous media are systematically varied to determine the impact on the eigenfrequencies and stability growth rates. Porous media is shown to increase the stability domain for a range of time delays (Tau) compared to similar cases without porous media.

Thermoacoustic Instability Model With Porous Media: Linear Stability Analysis and the Impact of Porous Media

2018 ◽  
Vol 141 (4) ◽  
Author(s):  
Cody S. Dowd ◽  
Joseph W. Meadows
Keyword(s):  
Growth Rate ◽  
Porous Media ◽  
Stability Analysis ◽  
Frequency Shift ◽  
Linear Stability ◽  
Linear Stability Analysis ◽  
Growth Rates ◽  
Thermoacoustic Instability ◽  
The Stability ◽  
The Impact

Lean premixed (LPM) combustion systems are susceptible to thermoacoustic instability, which occurs when acoustic pressure oscillations are in phase with the unsteady heat release rates. Porous media has inherent acoustic damping properties and has been shown to mitigate thermoacoustic instability; however, theoretical models for predicting thermoacoustic instability with porous media do not exist. In the present study, a one-dimensional (1D) model has been developed for the linear stability analysis of the longitudinal modes for a series of constant cross-sectional area ducts with porous media using a n-Tau flame transfer function (FTF). By studying the linear regime, the prediction of acoustic growth rates and subsequently the stability of the system is possible. A transfer matrix approach is used to solve for acoustic perturbations of pressure and velocity, stability growth rate, and frequency shift without and with porous media. The Galerkin approximation is used to approximate the stability growth rate and frequency shift, and it is compared to the numerical solution of the governing equations. Porous media is modeled using the following properties: porosity, flow resistivity, effective bulk modulus, and structure factor. The properties of porous media are systematically varied to determine the impact on the eigenfrequencies and stability growth rates. Porous media is shown to increase the stability domain for a range of time delays (Tau) compared to similar cases without porous media.

Sign in / Sign up

Export Citation Format

Share Document