Elastic-Plastic Finite Element Analysis of Nonsteady State Partial Slip Wheel-Rail Rolling Contact

2005 ◽  
Vol 127 (4) ◽  
pp. 713-721 ◽  
Author(s):  
Zefeng Wen ◽  
Xuesong Jin ◽  
Yanyao Jiang
Keyword(s):  
Finite Element Analysis ◽  
Plastic Deformation ◽  
Finite Element ◽  
Residual Stresses ◽  
Contact Force ◽  
Rolling Contact ◽  
Element Analysis ◽  
Normal Contact ◽  
Nonsteady State ◽  
Residual Stresses And Strains

A finite element analysis with the implementation of an advanced cyclic plasticity theory was conducted to study the elastic-plastic deformation under the nonsteady state rolling contact between a wheel and a rail. The consideration of nonsteady state rolling contact was restricted to a harmonic variation of the wheel-rail normal contact force. The normal contact pressure was idealized as the Hertzian distribution, and the tangential force presented by Carter was used. Detailed rolling contact stresses and strains were obtained for repeated rolling contact. The harmonic variation of the normal (vertical) contact force results in a wavy rolling contact surface profile. The results can help understand the influence of plastic deformation on the rail corrugation initiation and growth. The creepage or stick-slip condition greatly influences the residual stresses and strains. While the residual strains and surface displacements increased at a reduced rate with increasing rolling passes, the residual stresses stabilize after a limited number of rolling passes. The residual stresses and strains near the wave trough of the residual wavy deformation are higher than those near the wave crest.

Finite Element Analysis of the Rolling-Sliding Contact of Vibrationally Loaded Bearings Based on a Micro Friction Model

2013 ◽  
Vol 768-769 ◽  
pp. 714-722 ◽  
Author(s):  
Andreas Konrad ◽  
Wolfgang Nierlich ◽  
Jürgen Gegner
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Friction Coefficient ◽  
Residual Stresses ◽  
Equivalent Stress ◽  
Rolling Contact ◽  
Sliding Contact ◽  
Element Analysis ◽  
Fem Model ◽  
Mixed Friction

Mixed friction acting in a rolling contact increases the v. Mises equivalent stress and shifts the maximum towards the surface. Tangential stresses are superimposed to the stress distribution. The resulting position of the maximum v. Mises stress depends on the magnitude of the friction coefficient and is located directly on the surface from values of about 0.25 upwards. The impact of three-dimensional machine vibrations on rolling bearings in operation can cause severe mixed friction running conditions. Residual stress distributions measured on indentation-free raceways indicate high friction coefficients of up to greater than 0.25. The surfaces reveal smoothing of the finishing structure but no adhesive wear. The simulation of the vibrationally loaded rolling-sliding contact is based on the tribological model of localized friction coefficient. This approach avoids seizing by allowing for increased friction only in intermittently changing subareas of the contact at low sliding speed. The macroscopic friction coefficient, meeting a mixing rule, does not exceed 0.1. The finite element method (FEM) is used for the stress analysis. In the first step, a simplified FEM model involves a circumferentially oriented band of high friction coefficient from 0.2 to 0.5 within a cylindrical roller contact. The resulting depth distributions of the v. Mises equivalent stress during overrolling and the corresponding residual stresses are evaluated below the inner ring raceway of the bearing. The features of the FEM model are discussed in detail. The increased sliding friction in the band shifts the maximum of the v. Mises equivalent stress to the surface. Compressive residual stresses are induced in the edge zone. Depending on the applied Hertzian pressure, an additional subsurface peak occurs. First results of the finite element analysis are presented.

Analysis of Residual Stresses in Multi-Pass Welding Using Element Generation Technique

2006 ◽  
Vol 326-328 ◽  
pp. 1287-1290
Author(s):  
Jang Hyun Lee ◽  
Kyung Ho Lee ◽  
Chan Woo Lee
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Residual Stresses ◽  
Stress Distributions ◽  
Element Analysis ◽  
Butt Welding ◽  
Distortion Analysis ◽  
Finite Element Procedure ◽  
Residual Stresses And Strains ◽  
Solid Liquid

A finite element procedure to predict residual stresses on the multi-pass arc welding considering the multi-layered beads and solid–liquid phase transformation in the melted bead is implemented and experimentally validated. The nonlinearities of material properties are considered in the thermo-elasto-plastic distortion analysis. Element birth and death technique is used to simulate the weld metal added to base metal in both heat transfer and thermo-elasto-plastic analysis. Residual stresses and strains are computed for butt welding and T-joints fillet welding. The stress distributions calculated by proposed finite element analysis procedure are compared with the measured values of experiments and data available in the other studies. The efficiency of the proposed finite element analysis and experimental procedure is discussed and demonstrated.

Elastic-Plastic Finite-Element Analysis of Repeated, Two-Dimensional Wheel-Rail Rolling Contact under Time-Dependent Load

2006 ◽  
Vol 220 (5) ◽  
pp. 603-613 ◽  
Author(s):  
Z. F. Wen ◽  
X. S. Jin
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
Contact Force ◽  
Rolling Contact ◽  
Time Dependent ◽  
Two Dimensional ◽  
Normal Contact ◽  
Normal Contact Force ◽  
Residual Strains ◽  
Harmonic Variation

A study was performed using a finite-element model to obtain stresses, strains, and deformations for repeated, two-dimensional rolling contact of a locomotive driving wheel and a rail under time-dependent load. An advanced cyclic plasticity model was used with a commercial finite element code via a material subroutine. The time-dependent load was considered a harmonic variation of the wheel-rail normal contact force. The normal contact pressure was assumed to follow the Hertzian distribution and the tangential force followed the Carter distribution. A wavy profile is formed on the running surface of the rail subjected to the harmonic variation of the normal (vertical) contact force. The developed wavelength of the profile corresponds to the frequency of the normal contact force for the actual train speed. The creepage or rolling-sliding condition plays an important role in the residual strains and deformations, but its influence on the residual stresses is insignificant. The residual stresses at the surface decrease with increasing rolling passes and gradually tend to stabilize. The residual strains and surface displacements increase with increasing rolling cycle, but the increases in residual strain and surface displacement per rolling pass (ratchetting rate) decay. The residual stresses, strains, and deformations near the wave trough of the residual wavy deformation are larger than those near the wave crest. For any given creepage including zero value, when the number of rolling passes increases, the surface depth of the wavy-deformed surface increases but the ratchetting rate decays. The results are useful in investigating the influence of plastic deformation on rail corrugation.

Performance enhancement of normal contact ratio gearing system through correction factor

2019 ◽  
Vol 13 (3) ◽  
pp. 5242-5258
Author(s):  
R. Ravivarman ◽  
K. Palaniradja ◽  
R. Prabhu Sekar
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Correction Factor ◽  
Bending Strength ◽  
Performance Enhancement ◽  
Transmission Ratio ◽  
Contact Ratio ◽  
Element Analysis ◽  
Normal Contact ◽  
Root Region

As lined, higher transmission ratio drives system will have uneven stresses in the root region of the pinion and wheel. To enrich this agility of uneven stresses in normal-contact ratio (NCR) gearing system, an enhanced system is desirable to be industrialized. To attain this objective, it is proposed to put on the idea of modifying the correction factor in such a manner that the bending strength of the gearing system is improved. In this work, the correction factor is modified in such a way that the stress in the root region is equalized between the pinion and wheel. This equalization of stresses is carried out by providing a correction factor in three circumstances: in pinion; wheel and both the pinion and the wheel. Henceforth performances of this S+, S0 and S- drives are evaluated in finite element analysis (FEA) and compared for balanced root stresses in parallel shaft spur gearing systems. It is seen that the outcomes gained from the modified drive have enhanced performance than the standard drive.

Finite Element Analysis of the Rolling Contact Fatigue Life of Railcar Wheels

2008 ◽  
Vol 575-578 ◽  
pp. 1461-1466
Author(s):  
Byeong Choon Goo ◽  
Jung Won Seo
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Fatigue Life ◽  
Contact Fatigue ◽  
Rolling Contact ◽  
Element Analysis ◽  
Railway Vehicles ◽  
Contact Fatigue Life

Railcar wheels and axles belong to the most critical components in railway vehicles. The service conditions of railway vehicles have been more severe in recent years due to speed-up. Therefore, a more precise evaluation of railcar wheel life and safety has been requested. Wheel/rail contact fatigue and thermal cracks due to braking are two major mechanisms of the railcar wheel failure. One of the main sources influencing on the contact zone failure is residual stress. The residual stress in wheels formed during heat treatment in manufacturing changes in the process of braking. Thus the fatigue life of railcar wheels should be estimated by considering both thermal stress and rolling contact. Also, the effect of residual stress variation due to manufacturing process and braking process should be included in simulating contact fatigue behavior. In this paper, an evaluation procedure for the contact fatigue life of railcar wheels considering the effects of residual stresses due to heat treatment, braking and repeated contact load is proposed. And the cyclic stressstrain history for fatigue analysis is simulated by finite element analysis for the moving contact load.

Sign in / Sign up

Export Citation Format

Share Document