The Effect of Water Injection on Multispool Gas Turbine Behavior

2006 ◽  
Vol 128 (1) ◽  
pp. 97 ◽  
Author(s):  
A. J. Meacock ◽  
A. J. White
Keyword(s):  
Gas Turbine ◽  
Water Injection ◽  
Effect Of Water

scholarly journals Effect of Water Injection for NOx Reduction With Synthetic Liquid Fuels Containing High Fuel-Bound Nitrogen in a Gas Turbine Combustor

1981 ◽  
Author(s):  
P. R. Mulik ◽  
P. P. Singh ◽  
A. Cohn
Keyword(s):  
Gas Turbine ◽  
Liquid Fuel ◽  
Nox Reduction ◽  
Water Injection ◽  
Liquid Fuels ◽  
Gas Turbine Combustor ◽  
Synthetic Liquid Fuel ◽  
Effect Of Water ◽  
Combustion Tests ◽  
No Emissions

A total of five combustion tests utilizing water injection for control of NO, emissions have been conducted on three types of coal-derived liquid (CDL) fuels from the H-Coal and SRC II processes along with a shale-derived liquid (SDL) fuel supplied by the Radian Corporation. Actual testing was performed in a 0.14 m diameter gas-turbine-type combustor. For comparative purposes, each run with a synthetic liquid fuel was preceded by a baseline run utilizing No. 2 distillate oil. The effectiveness of water injection was found to decrease as the fuel-bound nitrogen (FBN) content of the synthetic liquids increased.

Field Conversion of a Low-Firing Frame 7B Gas Turbine Power Plant to Ultra-Low Emission Combustion

2015 ◽  
Author(s):  
Nicolas Demougeot ◽  
Jeffrey A. Benoit
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Energy Demand ◽  
Water Injection ◽  
Cost Benefit ◽  
High Energy ◽  
Nox Emissions ◽  
Environmental Controls ◽  
Low Emission ◽  
Technical Discussion

The search for power plant sustainability options continues as regulating agencies exert more stringent industrial gas turbine emission requirements on operators. Purchasing power for resale, de-commissioning current capabilities altogether and repowering by replacing or converting existing equipment to comply with emissions standards are economic-driven options contemplated by many mature gas turbine operators. NRG’s Gilbert power plant based in Milford, NJ began commercial operation in 1974 and is fitted with four (4) natural gas fired GE’s 7B gas turbine generators with two each exhausting to HRSG’s feeding one (1) steam turbine generator. The gas turbine units, originally configured with diffusion flame combustion systems with water injection, were each emitting 35 ppm NOx with the New Jersey High Energy Demand Day (HEED) regulatory mandate to reduce NOx emissions to sub 10 ppm by May 1st, 2015. Studies were conducted by the operator to evaluate the economic viability & installation of environmental controls to reduce NOx emissions. It was determined that installation of post-combustion environmental controls at the facility was both cost prohibitive and technically challenging, and would require a fundamental reconfiguration of the facility. Based on this economic analysis, the ultra-low emission combustion system conversion package was selected as the best cost-benefit solution. This technical paper will focus on the ultra low emissions technology and key features employed to achieve these low emissions, a description of the design challenges and solution to those, a summary of the customer considerations in down selecting options and an overview of the conversion scope. Finally, a technical discussion of the low emissions operational flexibility will be provided including performance results of the converted units.

Optimization of Mixture Formation of Diesel Fuel in a Small CI Engine: The Effect of Water (H2O) Injection Into Intake Port

2017 ◽  
Author(s):  
Se Hun Min ◽  
Jeonghyun Park ◽  
Hyun Kyu Suh
Keyword(s):  
Water Injection ◽  
Injection Timing ◽  
Intake Port ◽  
Cylinder Pressure ◽  
Test Results ◽  
Analysis Model ◽  
Simultaneous Reduction ◽  
Effect Of Water ◽  
Rate Of Heat Release ◽  
Ci Engine

The objective of this study is to investigate the effect of water injection into intake port on the performance of small CI engine. The ECFM-3Z model was applied for the combustion analysis model, and the amount of injected water were varied 10%, 20% and 30% of injected fuel mass. The results of this work were compared in terms of cylinder pressure, rate of heat release (ROHR), and the ISNO and soot emissions. It was found that the cylinder pressure was decreased from 1.2% to 9.2% when the amount of injected water was increased from 10% to 30%. In the results, NO emission significantly decreased from about 24% to about 85% when the amount of injected water increased due to the specific heat and latent heat of water. Considering the test results, the best conditions for the simultaneous reduction of NO and soot is the BTDC 05deg of injection timing and 30% of water injection mass. It can be expected the best IMEP and ISFC characteristics.

scholarly journals Time Effect of Water Injection on the Mechanical Properties of Coal and Its Application in Rockburst Prevention in Mining

Energies ◽  
2017 ◽  
Vol 10 (11) ◽  
pp. 1783 ◽  
Author(s):  
Xiaofei Liu ◽  
Guang Xu ◽  
Chong Zhang ◽  
Biao Kong ◽  
Jifa Qian ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Injection ◽  
Time Effect ◽  
Effect Of Water

Numerical Analysis of Gas Turbine Inlet Fogging Nozzle Manifold Pressure Drop

2014 ◽  
Author(s):  
Hai Zhang ◽  
Qun Zheng ◽  
Mustapha Chaker ◽  
Cyrus Meher-Homji
Keyword(s):  
Pressure Drop ◽  
Gas Turbine ◽  
Flow Resistance ◽  
Research Effort ◽  
Water Injection ◽  
Injection Velocity ◽  
Injection Angle ◽  
Turbine Inlet ◽  
Area Of Concern ◽  
Inlet Duct

The air pressure drop over the nozzles manifolds of inlet fogging system and the flow resistance downstream of the nozzle array (manifold) have always been an area of concern and is the object of this paper. Fogging nozzles arrays (involving several hundred nozzles) are mounted on channels and beams, downstream of the inlet filters and affect the pressure drop. The water injection angle, nozzle injection velocities and the progressive evaporation of the water droplets evaporation all influence the inlet pressure seen at the gas turbine inlet. This paper focuses on a numerical simulation investigation of flow resistance (pressure drop) of inlet fogging systems. In this research effort, the inlet duct is meshed in order to compute the pressure drop over the nozzles frames in fogging and non-fogging conditions. First, the resistance coefficients of an air intake filter are obtained by numerical and experimental methods, and then the coefficients are used for the simulation of the inlet duct by considering the filter as a porous media. Effects of nozzle spread pattern and water injection pattern are then modeled. The results indicate that injection velocity and arrangement of nozzles could have significant effects on the pressure drop and intake distortion, which will affect compressor performance. This paper provides a comprehensive analysis of the pressure drop and evaporation of inlet fogging and will be of value to gas turbine inlet fogging system designers and users.

Sign in / Sign up

Export Citation Format

Share Document