Influence of Tooth Profile Deviations on Helical Gear Wear

2004 ◽  
Vol 127 (4) ◽  
pp. 656-663 ◽  
Author(s):  
A. Kahraman ◽  
P. Bajpai ◽  
N. E. Anderson
Keyword(s):  
Gear Tooth ◽  
Helical Gear ◽  
Tooth Profile ◽  
Tooth Surface ◽  
Surface Wear ◽  
Mechanics Model ◽  
Surface Slopes ◽  
Tooth Surfaces ◽  
Computation Algorithm ◽  
Gear Contact

In this study, a surface wear prediction model for helical gears pairs is employed to investigate the influence of tooth profile deviations in the form of intentional tooth profile modifications or manufacturing errors on gear tooth surface wear. The wear model combines a finite-element-based gear contact mechanics model that predicts contact pressures, a sliding distance computation algorithm, and Archard’s wear formulation to predict wear of the contacting tooth surfaces. Typical helical gear tooth modifications are parameterized by an involute crown, a lead crown, and an involute slope. The influence of these parameters on surface wear are studied within typical tolerance ranges achievable using hob/shave process. The results indicate that wear is related to the combined modification parameters of a gear pair rather than individual gear parameters. At the end, a design formula is proposed that relates the mismatch of contacting surface slopes to the maximum initial wear rate.

Research on Gear Cutter Tooth Profile for Semi-Topping: A Case of a Helical Gear

1992 ◽  
Author(s):  
Y. Ariga ◽  
Shiyeyoshi Nagata
Keyword(s):  
Design Method ◽  
Gear Tooth ◽  
Helical Gear ◽  
Tooth Profile ◽  
Tooth Surface ◽  
Gear Cutting ◽  
Gear Cutter ◽  
Conventional Design ◽  
Wide Range ◽  
Tooth Number

Abstract Gear tooth tips are frequently chamfered to prevent nicks or scuffing on the tooth surface. Some of the hob cutters and pinion cutters can be chamfered but many types of cutters should be used for a particular range of tooth numbers since the amount chamfering largely varies depending on the tooth number. However, intensive efforts in the design have made it possible to produce cutters with little variation of chamfering amount for a wide range of tooth numbers. The error in the amount of chamfering by a single cutter designed by the above method can be maintained within ±10 % for gears with tooth numbers ranging from 16 to 94. It was found that three cutters of the conventional design are required for keeping the error within the same range for cutting gears within a given range of tooth numbers. The paper describes the tooth design method of the hob cutter with little variation of chamfering amount along changes in number of teeth to be machined and demonstrates that chamfering errors are maintained within practically allowable ranges for profile shift cutting or helical gear cutting with the use of this cutter.

A Surface Wear Prediction Methodology for Parallel-Axis Gear Pairs

2004 ◽  
Vol 126 (3) ◽  
pp. 597-605 ◽  
Author(s):  
P. Bajpai ◽  
A. Kahraman ◽  
N. E. Anderson
Keyword(s):  
Numerical Procedure ◽  
Surface Wear ◽  
Wear Prediction ◽  
Helical Gears ◽  
Coordinate Measurement ◽  
Mechanics Model ◽  
Manufacturing Errors ◽  
Tooth Surfaces ◽  
Parallel Axis ◽  
Gear Contact

In this study, a surface wear prediction methodology for spur and helical gears is proposed. The methodology employs a finite elements-based gear contact mechanics model in conjunction with the Archard’s wear formulation to predict wear of contacting tooth surfaces. An iterative numerical procedure is developed to account for the changes in the gear contact as the gears wear. A methodology is developed to import gear coordinate measurement machine data into the gear contact model in order to analyze gears with actual manufactured surfaces with profile and lead modifications. Results of an experimental study are presented for validation of the methodology. A set of simulations is also included to highlight the differences between gear pairs having modified and unmodified tooth surfaces, with and without manufacturing errors in terms of their wear characteristics.

A Surface Wear Prediction Model for Parallel-Axis Gear Pairs

2003 ◽  
Author(s):  
P. Bajpai ◽  
A. Kahraman ◽  
N. E. Anderson
Keyword(s):  
Prediction Model ◽  
Numerical Procedure ◽  
Surface Wear ◽  
Wear Prediction ◽  
Helical Gears ◽  
Coordinate Measurement ◽  
Mechanics Model ◽  
Tooth Surfaces ◽  
Parallel Axis ◽  
Gear Contact

In this study, a surface wear prediction model for spur and helical gears is proposed. The model employs a finite elements-based gear contact mechanics model in conjunction with the Archard’s wear formulation to predict wear of contacting tooth surfaces. An iterative numerical procedure is developed to account for the changes in the gear contact as the gears wear. A methodology is developed to import gear coordinate measurement machine data into the gear contact model in order to analyze gears with actual manufactured surfaces with profile and lead modifications. Results of an experimental study are presented for validation of the model. A set of simulations is also included to highlight the differences between gear pairs having modified and unmodified tooth surfaces, with and without manufacturing errors in terms of their wear characteristics.

Modeling of surface roughness in a novel magnetorheological gear profile finishing process

2020 ◽  
pp. 095440622097826
Author(s):  
Ravi Datt Yadav ◽  
Anant Kumar Singh ◽  
Kunal Arora
Keyword(s):  
Surface Roughness ◽  
Gear Tooth ◽  
Surface Characteristics ◽  
Spur Gear ◽  
Tooth Profile ◽  
Tooth Surface ◽  
Magnetic Flux Density ◽  
Element Analysis ◽  
Finishing Process ◽  
Gear Profile

Fine finishing of spur gears reduces the vibrations and noise and upsurges the service life of two mating gears. A new magnetorheological gear profile finishing (MRGPF) process is utilized for the fine finishing of spur gear teeth profile surfaces. In the present study, the development of a theoretical mathematical model for the prediction of change in surface roughness during the MRGPF process is done. The present MRGPF is a controllable process with the magnitude of the magnetic field, therefore, the effect of magnetic flux density (MFD) on the gear tooth profile has been analyzed using an analytical approach. Theoretically calculated MFD is validated experimentally and with the finite element analysis. To understand the finishing process mechanism, the different forces acting on the gear surface has been investigated. For the validation of the present roughness model, three sets of finishing cycle experimentations have been performed on the spur gear profile by the MRGPF process. The surface roughness of the spur gear tooth surface after experimentation was measured using Mitutoyo SJ-400 surftest and is equated with the values of theoretically calculated surface roughness. The results show the close agreement which ranges from −7.69% to 2.85% for the same number of finishing cycles. To study the surface characteristics of the finished spur gear tooth profile surface, scanning electron microscopy is used. The present developed theoretical model for surface roughness during the MRGPF process predicts the finishing performance with cycle time, improvement in the surface quality, and functional application of the gears.

Estimation of Gear Friction Coefficient using Directional Parameter of Tooth Surface

2021 ◽  
pp. 1-27
Author(s):  
Junichi Hongu ◽  
Ryohei Horita ◽  
Takao Koide
Keyword(s):  
Friction Coefficient ◽  
Contact Surface ◽  
Gear Tooth ◽  
Correction Term ◽  
Tooth Surface ◽  
Oil Film ◽  
Tooth Surfaces ◽  
Frictional Coefficients ◽  
Finishing Processes ◽  
The Relationship

Abstract This study proposes a modification of the Matsumoto equation using a directional parameter of tooth surfaces to adapt various gear finishing processes. The directional parameters of a contact surface, which affect oil film formations, have been discussed in the field of tribology; but this effect has been undetermined on the meshing gear tooth surfaces having directional machining marks. Thus, this paper investigates the relationship between the gear frictional coefficients and the directional parameters (based on ISO25178) of their tooth surfaces with the various finishing processes; and modifies the Matsumoto equation by introducing a new directional parameter to augment the various gear finishing processes. Our findings indicate that through optimizing the coefficient of the correction term the include the new directional parameter, the calculated friction values using the modified Matsumoto equation correlate more highly to the experimental friction values than that using the unmodified Matsumoto equation.

Vibration-based fault diagnosis of helical gear pair with tooth surface wear considering time-varying friction coefficient under mixed EHL condition

2021 ◽  
pp. 1-16
Author(s):  
Siyu Wang ◽  
Rupeng Zhu
Keyword(s):  
Dynamic Response ◽  
Hydrodynamic Lubrication ◽  
Helical Gear ◽  
Calculation Model ◽  
Tooth Surface ◽  
Time Varying ◽  
Gear Pair ◽  
Surface Wear ◽  
Mesh Stiffness ◽  
Helical Gear Pair

Abstract Based on “slice method”, the improved time-varying mesh stiffness (TVMS) calculation model of helical gear pair with tooth surface wear is proposed, in which the effect of friction force that obtained under mixed elasto-hydrodynamic lubrication (EHL) is considered in the model. Based on the improved TVMS calculation model, the dynamic model of helical gear system is established, then the influence of tooth wear parameters on the dynamic response is studied. The results illustrate that the varying reduction extents of mesh stiffness along tooth profile under tooth surface wear, in addition, the dynamic response in time-domain and frequency-domain present significant decline in amplitude under deteriorating wear condition.

A parameterized numerical method for generating discrete helical gear tooth surface allowing non-standard geometry

2008 ◽  
Vol 222 (6) ◽  
pp. 1033-1038 ◽  
Author(s):  
J Hedlund ◽  
A Lehtovaara
Keyword(s):  
Gear Tooth ◽  
Numerical Approach ◽  
Helical Gear ◽  
Tooth Surface ◽  
Tool Profile ◽  
Standard Geometry ◽  
Gear Manufacturing ◽  
Involute Gears ◽  
Gear Geometry ◽  
Tooth Flank

Gear analysis is typically performed using calculation based on gear standards. Standards provide a good basis in gear geometry calculation for involute gears, but these are unsatisfactory for handling geometry deviations such as tooth flank modifications. The efficient utilization of finite-element calculation also requires the geometry generation to be parameterized. A parameterized numerical approach was developed to create discrete helical gear geometry and contact line by simulating the gear manufacturing, i.e. the hobbing process. This method is based on coordinate transformations and a wide set of numerical calculation points and their synchronization, which permits deviations from common involute geometry. As an example, the model is applied to protuberance tool profile and grinding with tip relief. A fairly low number of calculation points are needed to create tooth flank profiles where error is <1 μm.

Tooth Undercutting of Beveloid Gears

2000 ◽  
Author(s):  
Chia-Chang Liu ◽  
Chung-Biau Tsay
Keyword(s):  
Gear Tooth ◽  
Singular Points ◽  
Tooth Surface ◽  
Involute Gear ◽  
Beveloid Gears ◽  
Tooth Surfaces

Abstract A beveloid gear can be viewed as an involute gear of which the profile-shifted coefficient linearly decreases from the heel to the toe. Therefore, tooth undercutting occurs and singular points appear on the tooth surfaces near the toe. When undercutting occurs, the gear tooth is comparatively weak. In this study, the conditions of tooth undercutting of beveloid gears were derived and specific phenomena were also investigated by numerical illustrated examples. In addition, according to the characteristics of tooth undercutting on the beveloid gear tooth surface, a novel type hob cutter with varying cutting depths was designed to avoid tooth undercutting of the beveloid gear.

Sign in / Sign up

Export Citation Format

Share Document