Low Cycle Fatigue Testing of Ball Grid Array Solder Joints under Mixed-Mode Loading Conditions

2004 ◽  
Vol 127 (3) ◽  
pp. 237-244 ◽  
Author(s):  
Tae-Sang Park ◽  
Soon-Bok Lee
Keyword(s):  
Fatigue Life ◽  
Mixed Mode ◽  
Room Temperature ◽  
Solder Joints ◽  
Low Cycle Fatigue ◽  
Ball Grid Array ◽  
Fatigue Tests ◽  
Test Method ◽  
Cycle Fatigue ◽  
Mixed Mode Loading

To give a proper and accurate estimation of the fatigue life of ball grid array (BGA) solder joints, a mechanical fatigue test method under mixed-mode loading is proposed. Experiments were conducted with 63Sn∕37Pb and Sn∕3.5Ag∕0.75Cu solder joints in room temperature. The mechanical low cycle fatigue tests were performed under several loading angles. The loading angle is controlled by several grips which have specific surface angle to the loading direction. Constant displacement controlled tests are performed using a micro-mechanical test apparatus. It was found that the normal deformation significantly affects the fatigue life of the solder joint. Throughout the whole test conditions at room temperature, Sn∕3.5Ag∕0.75Cu solder alloy had longer fatigue life than 63Sn∕37Pb alloy. Failure patterns of the fatigue tests were observed and discussed. A morrow energy model was examined and found to be a proper low cycle fatigue model for solder joints under mixed mode loading condition.

scholarly journals Impact of Temperature on Low-Cycle Fatigue Characteristics of the HR6W Alloy

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6741
Author(s):  
Grzegorz Junak ◽  
Anżelina Marek ◽  
Michał Paduchowicz
Keyword(s):  
Fatigue Life ◽  
Room Temperature ◽  
Low Cycle Fatigue ◽  
Fatigue Tests ◽  
Total Strain ◽  
Cycle Fatigue ◽  
Fatigue Characteristics

This paper presents the results of tests conducted on the HR6W (23Cr-45Ni-6W-Nb-Ti-B) alloy under low-cycle fatigue at room temperature and at 650 °C. Fatigue tests were carried out at constant values of the total strain ranges. The alloy under low-cycle fatigue showed cyclic strengthening both at room temperature and at 650 °C. The degree of HR6W strengthening described by coefficient n’ was higher at higher temperatures. At the same time, its fatigue life Nf at room temperature was, depending on the range of total strain adopted in the tests, several times higher than observed at 650 °C.

scholarly journals Fatigue Testing of Wearable Sensing Technologies: Issues and Opportunities

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4070
Author(s):  
Andrea Karen Persons ◽  
John E. Ball ◽  
Charles Freeman ◽  
David M. Macias ◽  
Chartrisa LaShan Simpson ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Prediction Models ◽  
Fatigue Testing ◽  
Low Cycle Fatigue ◽  
Wearable Sensors ◽  
Fatigue Tests ◽  
Proof Of Concept ◽  
Cycle Fatigue ◽  
Wearable Sensing ◽  
Failure Data

Standards for the fatigue testing of wearable sensing technologies are lacking. The majority of published fatigue tests for wearable sensors are performed on proof-of-concept stretch sensors fabricated from a variety of materials. Due to their flexibility and stretchability, polymers are often used in the fabrication of wearable sensors. Other materials, including textiles, carbon nanotubes, graphene, and conductive metals or inks, may be used in conjunction with polymers to fabricate wearable sensors. Depending on the combination of the materials used, the fatigue behaviors of wearable sensors can vary. Additionally, fatigue testing methodologies for the sensors also vary, with most tests focusing only on the low-cycle fatigue (LCF) regime, and few sensors are cycled until failure or runout are achieved. Fatigue life predictions of wearable sensors are also lacking. These issues make direct comparisons of wearable sensors difficult. To facilitate direct comparisons of wearable sensors and to move proof-of-concept sensors from “bench to bedside,” fatigue testing standards should be established. Further, both high-cycle fatigue (HCF) and failure data are needed to determine the appropriateness in the use, modification, development, and validation of fatigue life prediction models and to further the understanding of how cracks initiate and propagate in wearable sensing technologies.

Low Cycle Fatigue Properties of FGH720Li Superalloy

2021 ◽  
Vol 1035 ◽  
pp. 292-296
Author(s):  
Zi Chao Peng ◽  
Jun Ying Sheng ◽  
Xu Qing Wang ◽  
Yue Tang
Keyword(s):  
Fatigue Life ◽  
Powder Metallurgy ◽  
Applied Stress ◽  
Low Cycle Fatigue ◽  
Influencing Factor ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Nickel Base Superalloy ◽  
Loading Frequency ◽  
Cycle Fatigue

Low cycle fatigue (LCF) properties of a powder metallurgy(PM) nickel base superalloy FGH720Li were systematically studied in this work, including smooth LCF and notched LCF tested at various temperatures and different stress. The relationship between the fatigue life and applied stress was analyzed both for smooth fatigue and notch fatigue tests. The effects of loading frequency and stress ratio on LCF behavior were also studied. As an important influencing factor of the fatigue life in powder metallurgy superalloy, the effect of inclusions on LCF life was also investigated. The results showed that the fatigue properties of FGH720Li alloy was excellent, when tested at the temperature of 450°C and applied stress of 1230MPa, the fatigue life could exceed 5×104 cycles. When tested at 650°C and 1150MPa, the average fatigue life was still beyond 2×105 cycles.

Effect of Surface Finish and Loading Conditions on the Low Cycle Fatigue Life of Stainless Steel Welded Piping in PWR Environment

2013 ◽  
Author(s):  
Yuichi Fukuta ◽  
Yuichiro Nomura ◽  
Seiji Asada
Keyword(s):  
Stainless Steel ◽  
Fatigue Life ◽  
Austenitic Stainless Steel ◽  
Surface Finish ◽  
Loading Condition ◽  
Low Cycle Fatigue ◽  
Complex Loading ◽  
Fatigue Tests ◽  
Cycle Fatigue ◽  
Effect Of Surface

NUREG/CR-6909 of USA and JSME of Japan proposed new rules for evaluating environmental effects in fatigue analyses of reactors components. These rules were established from a lot of fatigue data with polished specimens under simple loading condition. The effects of surface finish or complex loading condition were reported in some papers, but these data were obtained with the simple shaped specimens. In order to evaluate the effects of surface finish and loading condition and to confirm the applicability of the proposed rules to actual components, Low Cycle Fatigue tests are performed in PWR environment with the specimens cut from 316 austenitic stainless steel welded piping. The pipes are machined to have three levels of surface finish condition and the load pattern simulating the thermal stress is applied to specimens. In this study, the effect of surface finish on fatigue life is included to be small for 316 austenitic stainless steel welded piping. Considering the insensitive region in the current evaluation rule, predicted accuracy is increased and possibility of improving the current rule is indicated.

Low Cycle Fatigue of Nuclear Pipe Components

1974 ◽  
Vol 96 (3) ◽  
pp. 171-176 ◽  
Author(s):  
J. D. Heald ◽  
E. Kiss
Keyword(s):  
Stainless Steel ◽  
Fatigue Life ◽  
Room Temperature ◽  
Fatigue Testing ◽  
Low Cycle Fatigue ◽  
304 Stainless Steel ◽  
Code Design ◽  
Hydraulic Pressure ◽  
Cycle Fatigue ◽  
Cyclic Bending

This paper presents the results of low-cycle fatigue testing and analysis of 26 piping components and butt-welded sections. The test specimens were fabricated from Type-304 stainless steel and carbon steel, materials which are typically used in the primary piping of light water nuclear reactors. Components included 6-in. elbows, tees, and girth butt-welded straight sections. Fatigue testing consisted of subjecting the specimens to deflection-controlled cyclic bending with the objective of simulating system thermal expansion type loading. Tests were conducted at room temperature and 550 deg F, with specimens at room temperature subjected to 1050 psi constant internal hydraulic pressure in addition to cyclic bending. In two tests at room temperature, however, stainless steel elbows were subjected to combined simultaneous cyclic internal pressure and cyclic bending. Predictions of the fatigue life of each of the specimens tested have been made according to the procedures specified in NB-3650 of Section III[1] in order to assess the code design margin. For the purpose of the assessment, predicted fatigue life is compared to actual fatigue life which is defined as the number of fatigue cycles producing complete through-wall crack growth (leakage). Results of this assessment show that the present code fatigue rules are adequately conservative.

Evaluation of Low-Cycle Fatigue in Simulated PWR Environment

2006 ◽  
Vol 326-328 ◽  
pp. 1011-1014 ◽  
Author(s):  
Ill Seok Jeong ◽  
Sang Jai Kim ◽  
Taek Ho Song ◽  
Sung Yull Hong
Keyword(s):  
Fatigue Life ◽  
Nuclear Power ◽  
Power Plants ◽  
Low Cycle Fatigue ◽  
Water Environment ◽  
Fatigue Tests ◽  
Cycle Fatigue ◽  
Fatigue Design ◽  
Number Of Cycles ◽  
Measured Length

For developing fatigue design curve of cast stainless steel that is used in piping material of nuclear power plants, a low-cycle fatigue test rig was built. It is capable of performing tests in pressurized high temperature water environment of PWR. Cylindrical solid fatigue specimens of CF8M were used for the strain-controlled environmental fatigue tests. Fatigue life was measured in terms of the number of cycles with the variation of strain amplitude at 0.04%/s strain rates. The disparity between target length and measured length of specimens was corrected by using finite element method. The corrected test results showed similar fatigue life trend with other previous results.

The Effect of Notches on the Fatigue Life of SCS-6/Ti3Al Composite

1990 ◽  
Vol 194 ◽  
Author(s):  
Kenneth R. Bain ◽  
Mary Lee Gambone ◽  
Richard D. Zordan
Keyword(s):  
Fatigue Life ◽  
Titanium Aluminide ◽  
Room Temperature ◽  
Composite System ◽  
Low Cycle Fatigue ◽  
Fatigue Tests ◽  
Fiber Direction ◽  
Sensitivity Factor ◽  
Load Axis ◽  
Circular Holes

AbstractLow cycle fatigue tests were performed on Ti-24Al-11Nb titanium aluminide composite unidirectionally reinforced with SCS-6 fiber. (SCS-6 is a SiC-based fiber manufactured by Textron-SMD in Lowell, Massachusetts.) The effect of circular holes onthe fatigue life of this composite system was measured with respect to fiber orientation, temperature, and frequency. Longitudinal and transverse specimens with and without holes were tested at 26°C and 649°C at 0.33 Hz. In addition, longitudinal specimens were also tested at 30 Hz and 649°C to determine the effect of frequency.A degradation in fatigue life due to the presence of holes was observed in specimens loaded in the fiber direction (longitudinally). This effect is independent of frequency. The notch sensitivity factor, Q, associated with the reduction in life ranges from 0.33 to 0.50 over the range of temperature tested.The specimens oriented with the load axis perpendicular to the fiber direction (transverse) demonstrated no sensitivity of fatigue life to the presence of holes at room temperature but did possess a finite sensitivity at 649°C with a Q=0.45.

Comparative Study of Microstructure and High Temperature Low Cycle Fatigue Behaviour of Nickel Base Superalloys Inconel 713LC and MAR-M247

2016 ◽  
Vol 713 ◽  
pp. 86-89 ◽  
Author(s):  
Ivo Šulák ◽  
Karel Obrtlík ◽  
Ladislav Čelko
Keyword(s):  
High Temperature ◽  
Fatigue Life ◽  
Low Cycle Fatigue ◽  
Strain Curve ◽  
Cyclic Stress ◽  
Fatigue Tests ◽  
Casting Defects ◽  
Cycle Fatigue ◽  
Stress Strain Curve ◽  
Nickel Base

The present work is focused on the study of microstructure and low cycle fatigue behavior of the first generation nickel-base superalloy IN 713LC (low carbon) and its promising second generation successor MAR-M247 HIP (hot isostatic pressing) at 900 °C. Microstructure of both alloys was studied by means of scanning electron microscopy (SEM). The microstructure of both materials is characterized by dendritic grains, carbides and casting defects. Size and morphology of precipitates and casting defects were evaluated. Fractographic observations have been made with the aim to reveal the fatigue crack initiation place and relation to the casting defects and material microstructure. Low cycle fatigue tests were conducted on cylindrical specimens in symmetrical push-pull cycle under strain control with constant total strain amplitude and strain rate at 900 °C in air. Hardening/softening curves, cyclic stress-strain curve and fatigue life data of both materials were obtained. Cyclic stress-strain curve of MAR M247 is shifted approximately to 120 MPa higher stress amplitudes in comparison with IN 713LC. Significantly higher fatigue life of MAR-M247 has been observed in Basquin representation. On the other hand IN 713LC shows prolonged lifetime compared with MAR-M247 in the Coffin-Manson representation. Results obtained from high temperature low cycle fatigue tests are discussed.

Sign in / Sign up

Export Citation Format

Share Document