An Experimental Study of Cutting Forces in High-Speed End Milling and Implications for Dynamic Force Modeling

2005 ◽  
Vol 127 (2) ◽  
pp. 251-261 ◽  
Author(s):  
P. T. Mativenga ◽  
K. K. B. Hon
Keyword(s):  
Frequency Domain ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Dynamic Force ◽  
High Speed Machining ◽  
Time Data ◽  
Dynamic Forces ◽  
Milling Forces ◽  
Aisi H13 Tool Steel

The characteristics of high-speed machining (HSM) dynamic milling forces was investigated. Recent studies in chip segmentation are discussed. A Mikron 700 High-Speed Machining Center was used in the end-milling of AISI H13 tool steel using PVD TiN coated two flute micrograin carbide tools. Dynamic force signals were studied using a real-time data acquisition system for spindle speeds from 3,750 to 31,500 rpm for a 6 mm dia tool. Frequency domain studies were also carried out for a larger tool of 12 mm dia for spindle speeds between 10,000 and 40,000 rpm. The trend and frequency domain aspects of the dynamic forces were evaluated and discussed. The fundamental concept of modeling cutting forces based on chip morphology is revisited. A new basis for modeling dynamic forces from the static component and harmonic contributions is presented. This approach for modeling the dynamic HSM force signal accounts for secondary harmonics.

An Experiment-Based Investigation on Characteristic and Model of Milling Forces during End-Milling Aluminum Alloy

2014 ◽  
Vol 494-495 ◽  
pp. 602-605
Author(s):  
Zeng Hui An ◽  
Xiu Li Fu ◽  
Ya Nan Pan ◽  
Ai Jun Tang
Keyword(s):  
Aluminum Alloy ◽  
Cutting Force ◽  
Cutting Forces ◽  
High Speed ◽  
Metal Cutting ◽  
End Milling ◽  
Influence Factors ◽  
Cutting Speed ◽  
Cutting Depth ◽  
Milling Forces

Cutting forces is one of the important physical phenomena in metal cutting process. It directly affects the surface quality of machining, tool life and cutting stability. The orthogonal experiments of cutting forces and influence factors with indexable and solid end mill were accomplished and the predictive model of milling force was established during high speed end milling 7050-T7451 aluminum alloy. The paper makes research mainly on the influence which the cutting speed, cutting depth and feed have on the cutting force. The experimental results of single factor showed that the cutting forces increase earlier and drop later with the increase of cutting speed, and the cutting speed of inflexion for 7050-T7451 is 1100m/min. As axial cutting depth, radial cutting depth and feed rate increase, the cutting force grows in different degree. The cutting force is particularly sensitive to axial cutting depth and slightly to the radial cutting depth.

Analytical Convolution Model of Cutting Forces in 3-D Ball End Milling

2001 ◽  
Author(s):  
Richard Y. Chiou ◽  
Bing Zhao
Keyword(s):  
Cutting Force ◽  
Frequency Domain ◽  
Cutting Forces ◽  
End Milling ◽  
Force Model ◽  
Three Dimensional Model ◽  
Calculation Algorithm ◽  
Ball End Milling ◽  
Convolution Model ◽  
Force Calculation

Abstract This paper presents an analytical convolution model of dynamic cutting forces in ball end milling of 3-D plane surfaces. The model takes into account the instantaneous slope on a sculptured surface to establish the chip geometry in cutting force calculation algorithm. A three-dimensional model of cutting forces in ball end milling is presented in terms of material properties, cutting parameters, machining configuration, and tool/work geometry. Based on the relationship of the local cutting force, chip load and engaged boundary, the total cutting force model is established via the angle domain convolution integration of the local forces in the feed, cross feed, axial direction, and inclination angle. The convolution integral leads to a periodic function of cutting forces in the angle domain and an explicit expression of the dynamic cutting force components in the frequency domain. Following the theoretical analysis, experimental study is discussed to illustrate the implementation procedure for force identification, and frequency domain data are presented to verify the analytical results.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

An AI-Based Model for Predicting Instananeous Cutting Force in End Milling

Manufacturing ◽  
2002 ◽  
Author(s):  
Hazim El-Mounayri ◽  
Vipul Tandon
Keyword(s):  
Cutting Force ◽  
Frequency Domain ◽  
Cutting Forces ◽  
End Milling ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Ann Model ◽  
Force Signal ◽  
Input Variables ◽  
Artificial Neural Network Ann

An Artificial Neural Network (ANN) model is developed to accurately predict the instantaneous cutting forces in flat end milling. A unique frequency domain approach is presented and is seen to simulate instantaneous cutting forces reasonably well. A set of eight input variables is chosen to represent the machining conditions and frequency domain parameters of the cutting force signal are generated. Three input parameters are varied, namely Feed, Speed and Depth of Cut. Four output parameters are suggested as a sufficient set to adequately reproduce the instantaneous cutting forces. Exhaustive experimentation is conducted to collect data (consisting of Fx, Fy, and Fz) to train and validate the model.

Tool Path Generation Method of Equal Approximation Error for Free-Form Surface in High Speed Machining

2010 ◽  
Vol 102-104 ◽  
pp. 544-549 ◽  
Author(s):  
Chun Jiang Zhou ◽  
Hong Chun Chen
Keyword(s):  
High Speed ◽  
Tool Path ◽  
Cutting Tool ◽  
End Milling ◽  
Approximation Error ◽  
Tool Path Generation ◽  
Free Form ◽  
Path Generation ◽  
High Speed Machining ◽  
Free Form Surface

The development of surface high-speed machining has put forward higher demands for uniform cutting load and smooth cutting tool path. Most current tool-path planning methods are based on constant scallop height, but they have the disadvantage of path point redundancy during the path discretization process. To overcome the problem, a tool path generation method of equal approximation error in each step for free-form surface is presented based on geodesic principle and curvature judgment. In this method, the NURBS curve is employed to realize smooth transition for adjacent two tool paths in high-speed machining. A certain angle of inclination of flat-end milling cutter during multi-axis machining improves the machining efficiency. Because of the advantage of this machining condition, the cutter location point generation algorithm during the machining condition is given by the method. The method is verified and simulated by C++. Experiment results proved that it can obtain uniform cutting load and continuous smooth cutting tool path during surface high-speed machining by the proposed method.

Structure Optimization Design and Application of a Strain Based Dynamometer

2013 ◽  
Vol 770 ◽  
pp. 385-390 ◽  
Author(s):  
Z. Huang ◽  
Wei Zhao ◽  
Ning He ◽  
Liang Li
Keyword(s):  
Natural Frequency ◽  
Cutting Forces ◽  
High Speed ◽  
Optimization Design ◽  
Dynamic Force ◽  
Force Component ◽  
High Speed Cutting ◽  
Milling Operations ◽  
Data Acquisition Software ◽  
Element Theory

A strain based dynamometer used for the prediction and measurement of three-component cutting forces for milling operations has been designed on the basis of the principle of additional elastic element theory. Meanwhile, four Wheatstone bridges, considerable amplifier and data acquisition software based on LabVIEW are also used to compose a whole system acquiring the cutting force signals. In order to obtain higher natural frequency and magnification, this paper focuses on the calculation and optimization of the dimensions of the special structure, and finally its first natural frequency can be stabilized at more than 14kHz, which are high enough to precisely measure the cutting forces, and the magnification can also achieve up to 15. The dynamic characteristics of the dynamometer are studied theoretically and experimentally, the results show that the developed dynamometer is able to measure the dynamic force component in high-speed cutting.

Sign in / Sign up

Export Citation Format

Share Document