Two-Dimensional Finite Element Analysis for Large Diameter Steel Flanges

2004 ◽  
Vol 126 (3) ◽  
pp. 399-403 ◽  
Author(s):  
Abdulmalik A. Alghamdi ◽  
Muhsen S. Al-Sannaa
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Internal Pressure ◽  
Elasticity Modulus ◽  
Large Diameter ◽  
Two Dimensional ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Gasket Material ◽  
Clamping Pressure

This paper presents numerical results obtained using Finite Element Analysis (FEA) in studying large diameter welded neck steel flanges under different loading conditions. Obtained FEA results show the effect of the clamping pressure, internal pressure, axial end load, temperature effect, gasket elasticity modulus on the contact pressure between the gasket and the steel flange. As expected clamping pressure is a determinate factor for the sealing condition. Gasket material is another primary factor in designing flanged joints.

Finite Element Analysis of the Forging Process for Half-Shaft Bushing

2009 ◽  
Vol 16-19 ◽  
pp. 1248-1252
Author(s):  
Chun Dong Zhu ◽  
Man Chun Zhang ◽  
Lin Hua
Keyword(s):  
Finite Element Method ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Numerical Calculation ◽  
Two Dimensional ◽  
Element Analysis ◽  
Forging Process ◽  
Die Life ◽  
Dimensional Finite Element ◽  
Forging Force

As an important forged part of an automobile, the inner hole of the half-shaft bushing must be formed directly. However, the process requires many steps, and how the forging, or deformation, is spread over the production steps directly affects the die life and forging force required. In this paper, the three steps involved in directly forging a half shaft bushing's inner hole are simulated using the two-dimensional finite element method. Further more, we improve the forging process. From numerical calculation, the improved necessary forging force is found to be only half the original force, and the die life is doubled.

Two-Dimensional Finite Element Analysis of Laboratory Seawall Model

2014 ◽  
Vol 580-583 ◽  
pp. 2134-2140
Author(s):  
Jian Zhang ◽  
Jian Feng Zhai ◽  
Xian Mei Wang ◽  
Jie Chen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Numerical Analysis ◽  
Numerical Results ◽  
Experimental Results ◽  
Base Layer ◽  
Two Dimensional ◽  
Element Analysis ◽  
Cemented Sand ◽  
Dimensional Finite Element

Two-Dimensional finite element analysis was used to investigate the performance of seawall construction over weak subgrade soil using artificial base layer material consisted of cemented sand cushion comprising geosynthetics materials. Two types of base layer materials pure sand and cemented sand comprising husk rich ash and two types of geosynthetics materials geogrid and geotextile were used. Constitutive models were used to represent different materials in numerical analysis. The competence of two-dimensional numerical analysis was compared with experimental results. Numerical results showed a superior harmony with the experimental results. Finite element analysis model proved to be a great tool to determine the parameters that are difficult to measure in laboratory experiments. In addition, finite element analysis has the benefit of cost and time saving when compared to experimental investigation work. Numerical results showed strain induced in geosynthetics eliminated beyond a distance approximately equal six times of footing width.

THREE DIMENSIONAL FINITE ELEMENT SIMULATION OF THE FRETTING WEAR PROBLEMS

2006 ◽  
Vol 20 (25n27) ◽  
pp. 3890-3895 ◽  
Author(s):  
CHOON YEOL LEE ◽  
JOON WOO BAE ◽  
BYUNG SUN CHOI ◽  
YOUNG SUCK CHAI
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Fretting Wear ◽  
Symmetric Model ◽  
Two Dimensional ◽  
Element Analysis ◽  
Inconel 690 ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

The structural integrity of steam generators in nuclear power plants is very much dependent upon the fretting wear characteristics of Inconel 690 U-tubes. In this study, a finite element analysis was used to investigate fretting wear on the secondary side of the steam generator, which arises from flow-induced vibrations (FIV) between the U-tubes and supports or foreign objects. Two-dimensional and three-dimensional finite element analyses were adopted to investigate the fretting wear problems. The purpose of the two-dimensional analysis, which simulated the contact between a punch and a plate, was to demonstrate the validity of using finite element analysis to analyze fretting wear problems. This was achieved by controlling the value of the wear constant and the number of cycles. The two-dimensional solutions obtained from this study were in good agreement with previous results reported by Strömberg. In the three-dimensional finite element analysis, a quarterly symmetric model was used to simulate tubes contacting at right angles. The results of the analyses showed donut-shaped wear along the contacting boundary, which is a typical feature of fretting wear.

Sign in / Sign up

Export Citation Format

Share Document