Liquefier Dynamics in Fused Deposition

2004 ◽  
Vol 126 (2) ◽  
pp. 237-246 ◽  
Author(s):  
Anna Bellini ◽  
Selc¸uk Gu¨c¸eri ◽  
Maurizio Bertoldi
Keyword(s):  
Rapid Prototyping ◽  
Flow Control ◽  
Fused Deposition Modeling ◽  
Control Strategies ◽  
Building Blocks ◽  
Layered Manufacturing ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Deposition Modeling

Layered manufacturing (LM) is an evolution of rapid prototyping (RP) technology whereby a part is built in layers. Fused deposition modeling (FDM) is a particular LM technique in which each section is fabricated through vector style deposition of building blocks, called roads, which are then stacked layer by layer to fabricate the final object. The latest improvements in this technology brought about the possibility of fabricating not only a model but even the finished product. This paper presents the analysis of the liquefier dynamics towards establishing control strategies for flow control during the extrusion phase, which is necessary to achieve the mentioned objective.

Influence of Built Orientation on Mechanical Properties in Fused Deposition Modeling

2014 ◽  
Vol 592-594 ◽  
pp. 400-404 ◽  
Author(s):  
Sandeep V. Raut ◽  
Vijaykumar S. Jatti ◽  
T.P. Singh
Keyword(s):  
Mechanical Properties ◽  
Rapid Prototyping ◽  
Fused Deposition Modeling ◽  
Polymer Materials ◽  
Manufacturing Cost ◽  
Layer By Layer ◽  
Total Cost ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Main Material

Fused deposition modeling (FDM) is one of the thirty techniques of rapid prototyping methods that produce prototypes from polymer materials (natural or with different grades). Acrylonitrile butadiene styrene (ABS) is one of the good material among all polymer materials. It is used in the layer by layer manufacturing of the prototype which is in the semi-molten plastic filament form and built up on the platform from bottom to top. In FDM, one of the critical factor is to select the built up orientation of the model since it affects the different areas of the model like main material, support material, built up time, total cost per part and most important the mechanical properties of the part. In view of this, objective of the present study was to investigate the effect of the built-up orientation on the mechanical properties and total cost of the FDM parts. Experiments were carried out on STRATASYS FDM type rapid prototyping machine coupled with CATALYST software and ABS as main material. Tensile and Impact specimens were prepared as per the ASTM standard with different built-up orientation and in three geometrical axes. It can be concluded from the experimental analysis that built orientation has significant affect on the tensile, impact and total cost of the FDM parts. These conclusions will help the design engineers to decide on proper build orientation, so that FDM parts can be fabricated with good mechanical properties at minimum manufacturing cost.

3D CAD, CAM and Rapid Prototyping Applied for Cam Fabrication

2014 ◽  
Vol 658 ◽  
pp. 553-556
Author(s):  
Daniel Besnea ◽  
Georgeta Ionascu ◽  
Mihai Avram ◽  
Lucian Bogatu ◽  
Alina Spanu
Keyword(s):  
Rapid Prototyping ◽  
Fused Deposition Modeling ◽  
Product Configuration ◽  
Layer By Layer ◽  
3D Cad ◽  
Fused Deposition ◽  
Modeling Process ◽  
Cad Cam ◽  
Deposition Modeling ◽  
Development Area

In this paper, a comparison between CNC manufacturing and Rapid Prototyping technology (FDM – Fused Deposition Modeling process), applied for a cam fabrication, is presented. In the products development area, a substantial support is offered by models, as intermediate between product configuration and technology design. The CAD/CAM/CNC technology is a widely used technique for creating prototypes, as well as production parts, using a subtractive type material-removal procedure from a semi-manufactured article. The rapid prototyping (RP) technologies are additive processes, where the part is built up layer by layer until done, directly from the 3D CAD model, within the precision limits of the chosen process. Similarities and differences between these two coexisting computer driven prototyping processes, the subtractive CNC 3 – axes milled part production and the additive RP/ FDM technique, are pointed out for a disk cam manufacturing as sample part.

An Update on the Use of Alginate in Additive Biofabrication Techniques

2019 ◽  
Vol 25 (11) ◽  
pp. 1249-1264 ◽  
Author(s):  
Amoljit Singh Gill ◽  
Parneet Kaur Deol ◽  
Indu Pal Kaur
Keyword(s):  
Fused Deposition Modeling ◽  
Low Cost ◽  
Selective Laser Sintering ◽  
Layer By Layer ◽  
Three Dimension ◽  
Anionic Polymer ◽  
Fused Deposition ◽  
The Status ◽  
Deposition Modeling ◽  
Extrusion Printing

Background: Solid free forming (SFF) technique also called additive manufacturing process is immensely popular for biofabrication owing to its high accuracy, precision and reproducibility. Method: SFF techniques like stereolithography, selective laser sintering, fused deposition modeling, extrusion printing, and inkjet printing create three dimension (3D) structures by layer by layer processing of the material. To achieve desirable results, selection of the appropriate technique is an important aspect and it is based on the nature of biomaterial or bioink to be processed. Result & Conclusion: Alginate is a commonly employed bioink in biofabrication process, attributable to its nontoxic, biodegradable and biocompatible nature; low cost; and tendency to form hydrogel under mild conditions. Furthermore, control on its rheological properties like viscosity and shear thinning, makes this natural anionic polymer an appropriate candidate for many of the SFF techniques. It is endeavoured in the present review to highlight the status of alginate as bioink in various SFF techniques.

Carbon Nanotube Reinforced Fused Deposition Modeling Using Microwave Irradiation

2016 ◽  
Author(s):  
Meng Zhang ◽  
Xiaoxu Song ◽  
Weston Grove ◽  
Emmett Hull ◽  
Z. J. Pei ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Additive Manufacturing ◽  
Microwave Irradiation ◽  
Computer Aided Design ◽  
Fused Deposition Modeling ◽  
Layer By Layer ◽  
Sem Images ◽  
Fused Deposition ◽  
Deposition Modeling

Additive manufacturing (AM) is a class of manufacturing processes where material is deposited in a layer-by-layer fashion to fabricate a three-dimensional part directly from a computer-aided design model. With a current market share of 44%, thermoplastic-based additive manufacturing such as fused deposition modeling (FDM) is a prevailing technology. A key challenge for AM parts (especially for parts made by FDM) in engineering applications is the weak inter-layer adhesion. The lack of bonding between filaments usually results in delamination and mechanical failure. To address this challenge, this study embedded carbon nanotubes into acrylonitrile butadiene styrene (ABS) thermoplastics via a filament extrusion process. The vigorous response of carbon nanotubes to microwave irradiation, leading to the release of a large amount of heat, is used to melt the ABS thermoplastic matrix adjacent to carbon nanotubes within a very short time period. This treatment is found to enhance the inter-layer adhesion without bulk heating to deform the 3D printed parts. Tensile and flexural tests were performed to evaluation the effects of microwave irradiation on mechanical properties of the specimens made by FDM. Scanning electron microscopic (SEM) images were taken to characterize the fracture surfaces of tensile test specimens. The actual carbon nanotube contents in the filaments were measured by conducting thermogravimetric analysis (TGA). The effects of microwave irradiation on the electrical resistivity of the filament were also reported.

scholarly journals Desain dan Pembuatan Prototype Piston Honda MEGAPRO FI Menggunakan 3D Printing

2020 ◽  
Vol 1 (2) ◽  
pp. 81-91
Author(s):  
Frince Marbun ◽  
Richard A.M. Napitupulu
Keyword(s):  
3D Printing ◽  
Computer Aided Design ◽  
Fused Deposition Modeling ◽  
Layer By Layer ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Manufacturing Technologies ◽  
Aided Design

3D printing technology has great potential in today's manufacturing world, one of its uses is in making miniatures or prototypes of a product such as a piston. One of the most famous and inexpensive 3D printing (additive manufacturing) technologies is Fused Deposition Modeling (FDM), the principle FDM works by thermoplastic extrusion through a hot nozzle at melting temperature then the product is made layer by layer. The two most commonly used materials are ABS and PLA so it is very important to know the accuracy of product dimensions. FDM 3D Printing Technology is able to make duplicate products accurately using PLA material. FDM machines work by printing parts that have been designed by computer-aided design (CAD) and then exported in the form of STL or .stl files and uploaded to the slicer program to govern the printing press according to the design. Using Anet A8 brand 3D printing tools that are available to the public, Slicing of general CAD geometry files such as autocad and solidwork is the basis for making this object. This software is very important to facilitate the design process to be printed. Some examples of software that can be downloaded and used free of charge such as Repetier-Host and Cura. by changing the parameters in the slicer software is very influential in the 3D printing manufacturing process.

Rapid Prototyping of Lower-Pair, Geared-Pair and Cam Mechanisms

2000 ◽  
Author(s):  
Thierry Laliberté ◽  
Clément M. Gosselin ◽  
Gabriel Côté
Keyword(s):  
Rapid Prototyping ◽  
Experimental Validation ◽  
Fused Deposition Modeling ◽  
3D Visualization ◽  
Fused Deposition ◽  
Lower Pair ◽  
Deposition Modeling ◽  
Kinematic Properties

Abstract In this paper, a framework for the rapid prototyping of lower-pair, geared-pair and cam mechanisms using a commercially available CAD package and a Fused Deposition Modeling (FDM) rapid prototyping machine is presented. A database of lower kinematic pairs (joints) is developed experimentally. Geared-pair and cam mechanisms are also developed. These mechanisms are then used in the design of the prototypes. Examples are presented in order to demonstrate the potential of this technique. Physical prototypes can be of great help in the design of mechanisms by allowing the 3D visualization of the mechanism as well as providing an experimental validation of the geometric and kinematic properties.

Sophisticated Production from Organic PLA Materials Processed Horizontally by Fused Deposition Modeling Method

2017 ◽  
Vol 756 ◽  
pp. 88-95
Author(s):  
Ema Nováková-Marcinčinová ◽  
Anton Panda ◽  
Ľudmila Nováková-Marcinčinová
Keyword(s):  
Mechanical Properties ◽  
Rapid Prototyping ◽  
Main Part ◽  
Fused Deposition Modeling ◽  
Experimental Testing ◽  
Fused Deposition ◽  
Two Samples ◽  
Static Tensile ◽  
Deposition Modeling

The article focuses on the samples production of organic material PLA-PolyLacticAcid – bioplastic. The main part describes the experimental testing of PolyLacticAcid plastic and sample production by Fused Deposition Modeling, Rapid Prototyping technology. The article presents selected carried out tests of mechanical properties focused mainly on the determination of ultimate tensile strength of two PLA-BIO plastic extruded horizontally along the width produced by FDM method, Rapid Prototyping. The authors of this article present their results of test materials in the form of measurement protocols recorded in software, the measured values in a static tensile test, recorded in tables and shown in work graphs. Based on the results of the two samples produced from PLA biomaterials and compared to determine which PLA – bioplastic is stronger.

Improving the Design of Peripheral IV Therapy by Employing Product Development Approach and Rapid Prototyping Technology

2014 ◽  
Vol 548-549 ◽  
pp. 1901-1904
Author(s):  
Yusoff Way ◽  
M. Azrai ◽  
A. Hadi Mohamad
Keyword(s):  
Product Development ◽  
Rapid Prototyping ◽  
Product Design ◽  
Fused Deposition Modeling ◽  
User Requirements ◽  
Concept Generation ◽  
Design And Development ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Development Approach

The aims of this research is to improve the design of IV cannula stopper or also known as heparin cap by utilizing the application of product design and development approach and employing Fused Deposition Modeling (FDM) machine. For this reason, the user requirements to identified target specifications and concept generation were proposed and the IV cannula stopper prototypes were fabricated using Rapid Prototyping technology (RP). This research would give an improvement over existing standard of IV cannula. The generated design from this research will improve the handling of IV cannula as well as ensuring its safety during the operation of IV cannula.

Sign in / Sign up

Export Citation Format

Share Document