Aerodynamic Blade Row Interactions in an Axial Compressor—Part II: Unsteady Profile Pressure Distribution and Blade Forces

2004 ◽  
Vol 126 (1) ◽  
pp. 45-51 ◽  
Author(s):  
Ronald Mailach ◽  
Konrad Vogeler
Keyword(s):  
Boundary Layer ◽  
Pressure Distribution ◽  
Pressure Sensors ◽  
Stability Limit ◽  
Leading Edge ◽  
Side Surface ◽  
Suction Side ◽  
Experimental Investigations ◽  
Unsteady Pressure ◽  
Blade Row

This two-part paper presents experimental investigations of unsteady aerodynamic blade row interactions in the first stage of the four-stage low-speed research compressor of Dresden. Both the unsteady boundary layer development and the unsteady pressure distribution of the stator blades are investigated for several operating points. The measurements were carried out on pressure side and suction side at midspan. In Part II of the paper the investigations of the unsteady pressure distribution on the stator blades are presented. The experiments were carried out using piezoresistive miniature pressure sensors, which are embedded into the pressure and suction side surface of a single blade. The unsteady pressure distribution on the blade is analyzed for the design point and an operating point near the stability limit. The investigations show that it is strongly influenced by both the incoming wakes and the potential flow field of the downstream rotor blade row. If a disturbance arrives the leading edge or the trailing edge of the blade the pressure changes nearly simultaneously along the blade chord. Thus the unsteady profile pressure distribution is independent of the wake propagation within the blade passage. A phase shift of the reaction on pressure and suction side is observed. The unsteady response of the boundary layer and the profile pressure distribution is compared. Based on the unsteady pressure distribution the unsteady pressure forces of the blades are calculated and discussed.

Aerodynamic Blade Row Interactions in an Axial Compressor: Part II — Unsteady Profile Pressure Distribution and Blade Forces

2003 ◽  
Author(s):  
Ronald Mailach ◽  
Konrad Vogeler
Keyword(s):  
Boundary Layer ◽  
Pressure Distribution ◽  
Pressure Sensors ◽  
Stability Limit ◽  
Leading Edge ◽  
Side Surface ◽  
Suction Side ◽  
Experimental Investigations ◽  
Unsteady Pressure ◽  
Blade Row

This two-part paper presents experimental investigations of unsteady aerodynamic blade row interactions in the first stage of the four-stage Low-Speed Research Compressor of Dresden. Both the unsteady boundary layer development and the unsteady pressure distribution of the stator blades are investigated for several operating points. The measurements were carried out on pressure side and suction side at midspan. In part II of the paper the investigations of the unsteady pressure distribution on the stator blades are presented. The experiments were carried out using piezoresistive miniature pressure sensors, which are embedded into the pressure and suction side surface of a single blade. The unsteady pressure distribution on the blade is analysed for the design point and an operating point near the stability limit. The investigations show that it is strongly influenced by both the incoming wakes and the potential flow field of the downstream rotor blade row. If a disturbance arrives the leading edge or the trailing edge of the blade the pressure changes nearly simultaneously along the blade chord. Thus the unsteady profile pressure distribution is independent of the wake propagation within the blade passage. A phase shift of the reaction on pressure and suction side is observed. The unsteady response of the boundary layer and the profile pressure distribution is compared. Based on the unsteady pressure distribution the unsteady pressure forces of the blades are calculated and discussed.

Rotor-Stator Interactions in a Four-Stage Low-Speed Axial Compressor—Part I: Unsteady Profile Pressures and the Effect of Clocking

2004 ◽  
Vol 126 (4) ◽  
pp. 507-518 ◽  
Author(s):  
Ronald Mailach ◽  
Konrad Vogeler
Keyword(s):  
Pressure Distribution ◽  
Axial Compressor ◽  
Leading Edge ◽  
Suction Side ◽  
Experimental Investigations ◽  
Low Speed ◽  
Unsteady Aerodynamic ◽  
Pressure Distributions ◽  
Blade Row ◽  
Pressure Changes

This two-part paper presents detailed experimental investigations of unsteady aerodynamic blade row interactions in the four-stage Low-Speed Research Compressor of Dresden. In part I of the paper the unsteady profile pressure distributions for the nominal setup of the compressor are discussed. Furthermore, the effect of blade row clocking on the unsteady profile pressures is investigated. Part II deals with the unsteady aerodynamic blade forces, which are calculated from the measured profile pressure distributions. The unsteady pressure distributions were analyzed in the first, a middle and the last compressor stage both on the rotor and stator blades. The measurements were carried out on pressure side and suction side at midspan. Several operating points were investigated. A complex behavior of the unsteady profile pressures can be observed, resulting from the superimposed influences of the wakes and the potential effects of several up- and downstream blade rows of the four-stage compressor. The profile pressure changes nearly simultaneously along the blade chord if a disturbance arrives at the leading edge or the trailing edge of the blade. Thus the unsteady profile pressure distribution is nearly independent of the convective wake propagation within the blade passage. A phase shift of the reaction of the blade to the disturbance on the pressure and suction side is observed. In addition, clocking investigations were carried out to distinguish between the different periodic influences from the surrounding blade rows. For this reason the unsteady profile pressure distribution on rotor 3 was measured, while stators 1–4 were separately traversed stepwise in the circumferential direction. Thus the wake and potential effects of the up- and downstream blade rows on the unsteady profile pressure could clearly be distinguished and quantified.

Rotor-Stator Interactions in a Four-Stage Low-Speed Axial Compressor: Part I — Unsteady Profile Pressures and the Effect of Clocking

2004 ◽  
Author(s):  
Ronald Mailach ◽  
Konrad Vogeler
Keyword(s):  
Pressure Distribution ◽  
Axial Compressor ◽  
Leading Edge ◽  
Suction Side ◽  
Experimental Investigations ◽  
Complex Behaviour ◽  
Low Speed ◽  
Unsteady Aerodynamic ◽  
Pressure Distributions ◽  
Blade Row

This two-part paper presents detailed experimental investigations of unsteady aerodynamic blade row interactions in the four-stage Low-Speed Research Compressor of Dresden. In part I of the paper the unsteady profile pressure distributions for the nominal setup of the compressor are discussed. Furthermore the effect of blade row clocking on the unsteady profile pressures is investigated. Part II deals with the unsteady aerodynamic blade forces, which are calculated from the measured profile pressure distributions. The unsteady pressure distributions were analysed in the first, a middle and the last compressor stage both on the rotor and stator blades. The measurements were carried out on pressure side and suction side at midspan. Several operating points were investigated. A complex behaviour of the unsteady profile pressures can be observed, resulting from the superimposed influences of the wakes and the potential effects of several up- and downstream blade rows of the four-stage compressor. The profile pressure changes nearly simultaneously along the blade chord if a disturbance arrives at the leading edge or the trailing edge of the blade. Thus the unsteady profile pressure distribution is nearly independent of the convective wake propagation within the blade passage. A phase shift of the reaction of the blade to the disturbance on the pressure and suction side is observed. In addition clocking investigations were carried out to distinguish between the different periodic influences from the surrounding blade rows. For this reason the unsteady profile pressure distribution on rotor 3 was measured, while stator 1–4 were separately traversed stepwise in the circumferential direction. Thus the wake and potential effects of the up- and downstream blade rows on the unsteady profile pressure could clearly be distinguished and quantified.

Periodical Unsteady Flow Within a Rotor Blade Row of an Axial Compressor: Part I — Flow Field at Midspan

2007 ◽  
Author(s):  
Ronald Mailach ◽  
Ingolf Lehmann ◽  
Konrad Vogeler
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Pressure Distribution ◽  
Rotor Blade ◽  
Laser Doppler Anemometry ◽  
Pressure Sensors ◽  
Stability Limit ◽  
Rotor Blades ◽  
Experimental Investigations ◽  
Blade Row

In this two-part paper results of the periodical unsteady flow field within the third rotor blade row of the four-stage Dresden Low-Speed Research Compressor are presented. The main part of the experimental investigations was performed using Laser-Doppler-Anemometry. Results of the flow field at several spanwise positions between midspan and rotor blade tip will be discussed. In addition time-resolving pressure sensors at midspan of the rotor blades provide information about the unsteady profile pressure distribution. In part I of the paper the flow field at midspan of the rotor blade row will be discussed. Different aspects of the blade row interaction process are considered for the design point and an operating point near the stability limit. The periodical unsteady blade-to-blade velocity field is dominated by the incoming stator wakes, while the potential effect of the stator blades is of minor influence. The inherent vortex structures and the negative jet effect, which is coupled to the wake appearance, are clearly resolved. Furthermore the time-resolved profile pressure distribution of the rotor blades is discussed. Although the negative jet effect within the rotor blade passage is very pronounced the rotor blade pressure distribution is nearly independent from the convectively propagating chopped stator wakes.

Stall inception mechanisms in a contra-rotating fan operating at different speed combinations

2019 ◽  
Vol 234 (8) ◽  
pp. 1041-1052 ◽  
Author(s):  
MP Manas ◽  
AM Pradeep
Keyword(s):  
Pressure Ratio ◽  
Pressure Sensors ◽  
Stability Limit ◽  
Leading Edge ◽  
Axial Direction ◽  
Tip Leakage Flow ◽  
Stall Inception ◽  
Unsteady Pressure ◽  
Stall Cells ◽  
The Stability

Contra-rotating fan is a concept that can possibly replace the present-day conventional fans due to its several aerodynamic advantages. It has the potential to improve the stability limit and can achieve a higher pressure ratio per stage. One of the advantages of a contra-rotating fan is its capability to operate both the rotors at different speeds. In the present study, experiments are carried out at different speed combinations of the rotors and the stall inception phenomenon is captured using high-response unsteady pressure sensors placed on the casing upstream of the leading edge of rotor-1. The unsteady pressure data are investigated using wavelet and Fourier analysis techniques. It is observed that the mechanism of stall inception is different for different speed combinations. The pre-stall disturbances fall in different frequency ranges for different speed combinations. For the range of speed combinations investigated, the frequency of appearance of stall cells of rotor-1 does not depend on the speed of rotor-2. A higher speed of rotation of rotor-1 leads to a higher frequency of appearance of stall cells and a lower speed of rotation of rotor-1 leads to a lower frequency of appearance of stall cells. For all the speed combinations, there is a range of frequency where no disturbance is observed and this range is termed as the ‘no-disturbance zone’. Disturbances are observed at lower frequencies and at frequencies close to the blade passing frequency. In order to understand the flow physics in detail, computational analysis is carried out for different speed combinations of the rotors. For a higher speed of rotor-2, it is observed that the suction effect of rotor-2 is significant enough to pull the tip-leakage flow towards the axial direction. Thus, the suction effect of rotor-2 plays a significant role in determining the stall of the stage.

Experimental Investigation of the Clocking Effect in a 1.5-Stage Axial Turbine—Part II: Unsteady Results and Boundary Layer Behavior

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
Sven König ◽  
Bernd Stoffel ◽  
M. Taher Schobeiri
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Measurement Techniques ◽  
Leading Edge ◽  
Suction Side ◽  
Experimental Investigations ◽  
Stress Signal ◽  
Upstream Direction ◽  
Loss Parameter ◽  
Lp Turbine

Comprehensive experimental investigations were conducted to get deeper insight into the physics of stator clocking in turbomachines. Different measurement techniques were used to investigate the influence of varying clocking positions on the highly unsteady flow field in a 1.5-stage axial low-pressure (LP) turbine. A Reynolds number typical for LP turbines as well as a two-dimensional blade design were chosen. Stator 2 was developed as a high-lift profile with a separation bubble on the suction side. This paper presents the results that were obtained by means of unsteady x-wire measurements upstream and downstream of Stator 2 and surface mounted hot-film measurements on the Stator 2 suction side. It was found that for the case when the Stator 1 wakes impinge close to the leading edge of Stator 2 the interaction between the Stator 1 and the rotor vortical structures takes place in proximity of the Stator 2 boundary layer, which leads to a shift of the transition point in the upstream direction. The major loss parameter concerning the Stator 2 aerodynamic performance could be attributed to the strength of the periodic fluctuations within the Stator 2 suction side boundary layer. A phase shift in the quasiwall shear stress signal in the front region of the Stator 2 vane was observed for different clocking positions.

Numerical Predictions of Turbine Cascade Secondary Flows and Heat Transfer With Inflow Turbulence

2020 ◽  
Author(s):  
Yousef Kanani ◽  
Sumanta Acharya ◽  
Forrest Ames
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Leading Edge ◽  
Suction Side ◽  
Lateral Spreading ◽  
Secondary Flows ◽  
Pressure Side ◽  
Initial Flow ◽  
Numerical Predictions ◽  
Inflow Turbulence

Abstract Turbine passage secondary flows are studied for a large rounded leading edge airfoil geometry considered in the experimental investigation of Varty et al. (J. Turbomach. 140(2):021010) using high resolution Large Eddy Simulation (LES). The complex nature of secondary flow formation and evolution are affected by the approach boundary layer characteristics, components of pressure gradients tangent and normal to the passage flow, surface curvature, and inflow turbulence. This paper presents a detailed description of the secondary flows and heat transfer in a linear vane cascade at exit chord Reynolds number of 5 × 105 at low and high inflow turbulence. Initial flow turning at the leading edge of the inlet boundary layer leads to a pair of counter-rotating flow circulation in each half of the cross-plane that drive the evolution of the pressure-side and suction side of the near-wall vortices such as the horseshoe and leading edge corner vortex. The passage vortex for the current large leading-edge vane is formed by the amplification of the initially formed circulation closer to the pressure side (PPC) which strengthens and merges with other vortex systems while moving toward the suction side. The predicted suction surface heat transfer shows good agreement with the measurements and properly captures the augmented heat transfer due to the formation and lateral spreading of the secondary flows towards the vane midspan downstream of the vane passage. Effects of various components of the secondary flows on the endwall and vane heat transfer are discussed in detail.

Computation and Simulation of Wake-Generated Unsteady Pressure and Boundary Layers in Cascades: Part 1 — Description of the Approach and Validation

1994 ◽  
Author(s):  
S. Fan ◽  
B. Lakshminarayana
Keyword(s):  
Boundary Layer ◽  
Unsteady Flow ◽  
Flat Plate ◽  
Boundary Layers ◽  
Guide Vane ◽  
Numerical Procedure ◽  
Computational Domain ◽  
Unsteady Pressure ◽  
Blade Row ◽  
Euler Solver

The unsteady pressure and boundary layers on a turbomachinery blade row arising from periodic wakes due to upstream blade rows are investigated in this paper. A time accurate Euler solver has been developed using an explicit four-stage Runge-Kutta scheme. Two dimensional unsteady non-reflecting boundary conditions are used at the inlet and the outlet of the computational domain. The unsteady Euler solver captures the wake propagation and the resulting unsteady pressure field, which is then used as the input for a 2-D unsteady boundary layer procedure to predict the unsteady response of blade boundary layers. The boundary layer code includes an advanced k-ε model developed for unsteady turbulent boundary layers. The present computational procedure has been validated against analytic solutions and experimental measurements. The validation cases include unsteady inviscid flows in a flat plate cascade and a compressor exit guide vane (EGV) cascade, unsteady turbulent boundary layer on a flat plate subject to a traveling wave, unsteady transitional boundary layer due to wake passing and unsteady flow at the mid-span section of an axial compressor stator. The present numerical procedure is both efficient and accurate in predicting the unsteady flow physics resulting from wake/blade-row interaction, including wake induced unsteady transition of blade boundary layers.

Periodical Unsteady Flow Within a Rotor Blade Row of an Axial Compressor: Part II — Wake–Tip Clearance Vortex Interaction

2007 ◽  
Author(s):  
Ronald Mailach ◽  
Ingolf Lehmann ◽  
Konrad Vogeler
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Rotor Blade ◽  
Pressure Sensors ◽  
Tip Clearance ◽  
Experimental Investigations ◽  
Lower Velocity ◽  
Blade Row ◽  
Blade Tip ◽  
Tip Clearance Vortex

In this two-part paper results of the periodical unsteady flow field within the third rotor blade row of the four-stage Dresden Low-Speed Research Compressor are presented. The main part of the experimental investigations was performed using Laser-Doppler-Anemometry. Results of the flow field at several spanwise positions between midspan and rotor blade tip will be discussed. In addition time-resolving pressure sensors at midspan of the rotor blades provide information about the unsteady profile pressure distribution. In part II of the paper the flow field in the rotor blade tip region will be discussed. The experimental results reveal a strong periodical interaction of the incoming stator wakes and the rotor blade tip clearance vortices. Consequently, in the rotor frame of reference the tip clearance vortices are periodical with the stator blade passing frequency. Due to the wakes the tip clearance vortices are separated into different segments. Along the mean vortex trajectory these parts can be characterised by alternating patches of higher and lower velocity and flow turning or subsequent counterrotating vortex pairs. These flow patterns move downstream along the tip clearance vortex path in time. As a result of the wake influence the orientation and extension of the tip clearance vortices as well as the flow blockage periodically vary in time.

Leading-edge receptivity of a hypersonic boundary layer on a flat plate

2001 ◽  
Vol 426 ◽  
pp. 73-94 ◽  
Author(s):  
A. A. MASLOV ◽  
A. N. SHIPLYUK ◽  
A. A. SIDORENKO ◽  
D. ARNAL
Keyword(s):  
Boundary Layer ◽  
Acoustic Waves ◽  
Free Stream ◽  
Three Dimensional ◽  
Leading Edge ◽  
Experimental Investigations ◽  
Two Dimensional ◽  
Inclination Angles ◽  
Tollmien Schlichting ◽  
Radiation Conditions

Experimental investigations of the boundary layer receptivity, on the sharp leading edge of a at plate, to acoustic waves induced by two-dimensional and three- dimensional perturbers, have been performed for a free-stream Mach number M∞ = 5.92. The fields of controlled free-stream disturbances were studied. It was shown that two-dimensional and three-dimensional perturbers radiate acoustic waves and that these perturbers present a set of harmonic motionless sources and moving sources with constant amplitude. The disturbances excited in the boundary layer were measured. It was found that acoustic waves impinging on the leading edge generate Tollmien–Schlichting waves in the boundary layer. The receptivity coefficients were obtained for several radiation conditions and intensities. It was shown that there is a dependence of receptivity coefficients on the wave inclination angles.

Sign in / Sign up

Export Citation Format

Share Document