Integrated Dynamic Thermo-Mechanical Modeling of High Speed Spindles, Part 2: Solution Procedure and Validations

2004 ◽  
Vol 126 (1) ◽  
pp. 159-168 ◽  
Author(s):  
Hongqi Li ◽  
Yung C. Shin
Keyword(s):  
High Speed ◽  
Solution Procedure ◽  
Operating Conditions ◽  
Test Results ◽  
Mechanical Modeling ◽  
Spindle Bearing ◽  
Wide Range ◽  
Bearing Stiffness ◽  
Models Validation ◽  
Validation Tests

This paper presents a new solution procedure for an integrated thermo-dynamic spindle model and validation results. Based on the model presented in Part 1 of this paper, a computer program has been developed to generate comprehensive solutions for high speed spindle-bearing systems, such as bearing stiffness, contact load and temperature, spindle dynamic characteristics and response, temperature distributions, and thermal expansions. The model and the solution procedure are modular such that solutions for different spindle set-ups can be easily generated by combining a given spindle model with different toolholder models. Validation test results for thermal and dynamic predictions are presented for four different spindle systems, including the thermal and dynamic validation tests on a specially constructed spindle testbed. The validation results show the model has accurate predictive capabilities for a wide range of operating conditions and various spindle designs.

Characteristics of air entrainment during dynamic wetting failure along a planar substrate

2014 ◽  
Vol 747 ◽  
pp. 119-140 ◽  
Author(s):  
E. Vandre ◽  
M. S. Carvalho ◽  
S. Kumar
Keyword(s):  
High Speed ◽  
Water Solution ◽  
Air Entrainment ◽  
Dynamic Contact ◽  
Operating Conditions ◽  
Dynamic Wetting ◽  
Glycerol Water ◽  
Planar Substrate ◽  
Wide Range ◽  
Stationary Plate

AbstractCharacteristic substrate speeds and meniscus shapes associated with the onset of air entrainment are studied during dynamic wetting failure along a planar substrate. Using high-speed video, the behaviour of the dynamic contact line (DCL) is recorded as a tape substrate is drawn through a bath of a glycerol/water solution. Air entrainment is identified by triangular air films that elongate from the DCL above some critical substrate speed. Meniscus confinement within a narrow gap between the substrate and a stationary plate is shown to delay air entrainment to higher speeds for a wide range of liquid viscosities, expanding upon the findings of Vandre, Carvalho & Kumar (J. Fluid Mech., vol. 707, 2012, pp. 496–520). A pressurized liquid reservoir controls the meniscus position within the confinement gap. It is found that liquid pressurization further postpones air entrainment when the meniscus is located near a sharp corner along the stationary plate. Meniscus shapes recorded near the DCL demonstrate that operating conditions influence the size of entrained air films, with smaller films appearing in the more viscous solutions. Regardless of size, air films become unstable to thickness perturbations and ultimately rupture, leading to the entrainment of air bubbles. Recorded critical speeds and air-film sizes compare well to predictions from a hydrodynamic model for dynamic wetting failure, suggesting that strong air stresses near the DCL trigger the onset of air entrainment.

Subsynchronous Vibration Patterns Under Reduced Oil Supply Flow Rates

2017 ◽  
Author(s):  
B. R. Nichols ◽  
R. L. Fittro ◽  
C. P. Goyne
Keyword(s):  
Flow Rate ◽  
High Speed ◽  
Operating Conditions ◽  
System Stability ◽  
Supporting Evidence ◽  
Test Rig ◽  
Flow Rates ◽  
Oil Supply ◽  
Bending Mode ◽  
Wide Range

Many high-speed, rotating machines across a wide range of industrial applications depend on fluid film bearings to provide both static support of the rotor and to introduce stabilizing damping forces into the system through a developed hydrodynamic film wedge. Reduced oil supply flow rate to the bearings can cause cavitation, or a lack of a fully developed film layer, at the leading edge of the bearing pads. Reducing oil flow has the well-documented effects of higher bearing operating temperatures and decreased power losses due to shear forces. While machine efficiency may be improved with reduced lubricant flow, little experimental data on its effects on system stability and performance can be found in the literature. This study looks at overall system performance of a test rig operating under reduced oil supply flow rates by observing steady-state bearing performance indicators and baseline vibrational response of the shaft. The test rig used in this study was designed to be dynamically similar to a high-speed industrial compressor. It consists of a 1.55 m long, flexible rotor supported by two tilting pad bearings with a nominal diameter of 70 mm and a span of 1.2 m. The first bending mode is located at approximately 5,000 rpm. The tiling-pad bearings consist of five pads in a vintage, flooded bearing housing with a length to diameter ratio of 0.75, preload of 0.3, and a load-between-pad configuration. Tests were conducted over a number of operating speeds, ranging from 8,000 to 12,000 rpm, and bearing loads, while systematically reducing the oil supply flow rates provided to the bearings under each condition. For nearly all operating conditions, a low amplitude, broadband subsynchronous vibration pattern was observed in the frequency domain from approximately 0–75 Hz. When the test rig was operated at running speeds above its first bending mode, a distinctive subsynchronous peak emerged from the broadband pattern at approximately half of the running speed and at the first bending mode of the shaft. This vibration signature is often considered a classic sign of rotordynamic instability attributed to oil whip and shaft whirl phenomena. For low and moderate load conditions, the amplitude of this 0.5x subsynchronous peak increased with decreasing oil supply flow rate at all operating speeds. Under the high load condition, the subsynchronous peak was largely attenuated. A discussion on the possible sources of this subsynchronous vibration including self-excited instability and pad flutter forced vibration is provided with supporting evidence from thermoelastohydrodynamic (TEHD) bearing modeling results. Implications of reduced oil supply flow rate on system stability and operational limits are also discussed.

Dynamics of Machine Tool Spindle/Bearing Systems Under Thermal Growth

1997 ◽  
Vol 119 (4) ◽  
pp. 875-882 ◽  
Author(s):  
Bert R. Jorgensen ◽  
Yung C. Shin
Keyword(s):  
Thermal Expansion ◽  
Dynamic Response ◽  
Heat Generation ◽  
High Speed ◽  
Transfer Model ◽  
Good Prediction ◽  
High Speeds ◽  
Spindle Bearing ◽  
Thermal Growth ◽  
Bearing Stiffness

Increased use of high-speed machining creates the need to predict spindle/bearing performance at high speeds. Spindle dynamic response is a function of the nonlinear bearing stiffness. At high speeds, thermal expansion can play an important role in bearing stiffness. A complete bearing load-deflection analysis including thermal expansion is derived and is coupled with an analysis of spindle dynamic response. Steady-state temperature distribution is found from heat generation at the contact point and from a quasi three-dimensional heat transfer model. Numerical solutions give a good prediction of thermal growth and heat generation in the bearing. Predicted high-speed spindle frequencies show good agreement with experimentation. The effects of loading condition and bearing material type on bearing stiffness are also shown.

Assessment of engine combustion network recommendations for measurement of ignition and lift-off length

2020 ◽  
pp. 146808742092264
Author(s):  
Boni F Yraguen ◽  
Farzad Poursadegh ◽  
Caroline L Genzale
Keyword(s):  
Ignition Delay ◽  
High Speed ◽  
Operating Conditions ◽  
Bias Error ◽  
Ambient Conditions ◽  
Intensity Histogram ◽  
Wide Range ◽  
Engine Combustion ◽  
Length Measurements ◽  
Lift Off

The engine combustion network recommends two different imaging-based diagnostics for the measurement of diesel spray ignition delay and lift-off length, respectively. To measure ignition delay, high-speed imaging of broadband luminosity, spectrally filtered to limit collected wavelengths below 600 nm, is recommended. This diagnostic is often referred to as broadband natural luminosity. For lift-off length measurements, the engine combustion network recommends imaging of OH* chemiluminescence. This diagnostic requires using an image-intensified camera to detect narrowly filtered light around 310 nm. Alternatively, it has been shown that the lift-off length can be measured using broadband natural luminosity, avoiding the need for an intensifier and ultraviolet-transmitting optics. However, care is needed in the collection and processing of this diagnostic to accurately isolate the chemiluminescence signal. Particularly, standard intensity thresholding techniques are not sufficient for isolating the chemiluminescence signal in broadband natural luminosity images. Thus, an intensity-histogram-based thresholding method is introduced. This article assesses the feasibility and practicality of measuring lift-off length using broadband natural luminosity using a detailed comparison to OH* chemiluminescence measurements. It is shown that lift-off length measurements using broadband natural luminosity are prone to user bias error in the optical setup and data processing, especially under moderate- to high-sooting conditions. We conclude that while OH* imaging provides the most reliable and accurate measurement of lift-off length at a wide range of ambient conditions, an intensity-histogram analysis can help discriminate the high-temperature chemiluminescence signal from others in a broadband natural luminosity image at higher-sooting operating conditions than demonstrated in current literature.

Experimental Validation of a Wide-Range Centrifugal Compressor Stage for Supercritical CO2 Power Cycles

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Timothy C. Allison ◽  
Natalie R. Smith ◽  
Robert Pelton ◽  
Jason C. Wilkes ◽  
Sewoong Jung
Keyword(s):  
Centrifugal Compressor ◽  
Operating Conditions ◽  
Successful Implementation ◽  
Compressor Stage ◽  
Test Results ◽  
Power Cycles ◽  
Casing Treatment ◽  
Centrifugal Compressor Stage ◽  
Operating Range ◽  
Wide Range

Successful implementation of sCO2 power cycles requires high compressor efficiency at both the design-point and over a wide operating range in order to maximize cycle power output and maintain stable operation over a wide range of transient and part-load operating conditions. This requirement is particularly true for air-cooled cycles where compressor inlet density is a strong function of inlet temperature that is subject to daily and seasonal variations as well as transient events. In order to meet these requirements, a novel centrifugal compressor stage design was developed that incorporates multiple novel range extension features, including a passive recirculating casing treatment and semi-open impeller design. This design, presented and analyzed for CO2 operation in a previous paper, was fabricated via direct metal laser sintering and tested in an open-loop test rig in order to validate simulation results and the effectiveness of the casing treatment configuration. Predicted performance curves in air and CO2 conditions are compared, resulting in a reduced diffuser width requirement for the air test in order to match design velocities and demonstrate the casing treatment. Test results show that the casing treatment performance generally matched computational fluid dynamics (CFD) predictions, demonstrating an operating range of 69% and efficiency above air predictions across the entire map. The casing treatment configuration demonstrated improvements over the solid wall configuration in stage performance and flow characteristics at low flows, resulting in an effective 14% increase in operating range with a 0.5-point efficiency penalty. The test results are also compared to a traditional fully shrouded impeller with the same flow coefficient and similar head coefficient, showing a 42% range improvement over traditional designs.

scholarly journals Cyclic NO2:NOx ratio from a diesel engine undergoing transient load steps

2019 ◽  
Vol 22 (1) ◽  
pp. 284-294 ◽  
Author(s):  
FCP Leach ◽  
MH Davy ◽  
MS Peckham
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Formation Mechanisms ◽  
Exhaust Gas ◽  
Work Cycle ◽  
Wide Range ◽  
Gas Recirculation ◽  
Aftertreatment Systems

As the control of real driving emissions continues to increase in importance, the importance of understanding emission formation mechanisms during engine transients similarly increases. Knowledge of the NO2/NOx ratio emitted from a diesel engine is necessary, particularly for ensuring optimum performance of NOx aftertreatment systems. In this work, cycle-to-cycle NO and NOx emissions have been measured using a Cambustion CLD500, and the cyclic NO2/NOx ratio calculated as a high-speed light-duty diesel engine undergoes transient steps in load, while all other engine parameters are held constant across a wide range of operating conditions with and without exhaust gas recirculation. The results show that changes in NO and NOx, and hence NO2/NOx ratio, are instantaneous upon a step change in engine load. NO2/NOx ratios have been observed in line with previously reported results, although at the lightest engine loads and at high levels of exhaust gas recirculation, higher levels of NO2 than have been previously reported in the literature are observed.

The Non-Uniform Preloading Effect on Stiffness Behaviour of Angular Contact Ball Bearings

2012 ◽  
Author(s):  
Wenwu Wu ◽  
Jun Hong ◽  
Xiaohu Li ◽  
Yang Li ◽  
Baotong Li
Keyword(s):  
High Speed ◽  
Ball Bearing ◽  
Operating Conditions ◽  
Structural Performance ◽  
Angular Contact Ball Bearing ◽  
Actual Operating ◽  
Bearing Life ◽  
Bearing Stiffness ◽  
Increasing Demand ◽  
Bearing System

With the increasing demand of higher operating speed for bearing system, more challenges have been exposed on the maintaining of the bearing performance. Preloading is an effective method to handle these challenges. Traditionally, the preloading of bearing system has been applied by uniform approaches such as rigid preload and constant preload. However, this treatment may hardly deal with the optimization of preloading problem due to the non-uniformity of the bearing stiffness becomes more apparent under high-speed operating conditions. A novel and practical approach is therefore presented in this paper to incorporate the non-uniformity effect to improve the structural performance of bearing under actual operating conditions. Firstly, the critical relationship between the stiffness behaviour and the non-uniform preload is evaluated for bearing system. The stiffness problem of angular contact ball bearing system is then formulated analytically by Jones’ model. With this approach, boundary conditions are achieved to solve the local contact deformation and predict the bearing life under non-uniform preload. Finally, both the uniform preload and the non-uniform preload cases for bearing system are simulated under various operating conditions. Comparing with traditional methods, the proposed method can provide a better solution in both stiffness and life that will enable a designer to obtain a deep insight on the optimization of bearing system.

Influence of Stator Blade Geometry on Torque Converter Cavitation

2017 ◽  
Vol 140 (4) ◽  
Author(s):  
Cheng Liu ◽  
Wei Wei ◽  
Qingdong Yan ◽  
Brian K. Weaver ◽  
Houston G. Wood
Keyword(s):  
High Speed ◽  
Torque Converter ◽  
Operating Conditions ◽  
Hydrodynamic Performance ◽  
Speed Ratio ◽  
Capacity Loss ◽  
Wide Range ◽  
Stator Blade ◽  
Torque Converters ◽  
Blade Geometry

Cavitation in torque converters may cause degradation in hydrodynamic performance, severe noise, or even blade damage. Researches have highlighted that the stator is most susceptible to the occurrence of cavitation due to the combination of high flow velocities and high incidence angles. The objective of this study is to therefore investigate the effects of cavitation on hydrodynamic performance as well as the influence of stator blade geometry on cavitation. A steady-state homogeneous computational fluid dynamics (CFD) model was developed and validated against test data. It was found that cavitation brought severe capacity constant degradation under low-speed ratio (SR) operating conditions and vanished in high-speed ratio operating conditions. A design of experiments (DOE) study was performed to investigate the influence of stator design variables on cavitation over various operating conditions, and it was found that stator blade geometry had a significant effect on cavitation behavior. The results show that stator blade count and leaning angle are important variables in terms of capacity constant loss, torque ratio (TR) variance, and duration of cavitation. Large leaning angles are recommended due to their ability to increase the cavitation number in torque converters over a wide range of SRs, leading to less stall capacity loss as well as a shorter duration of cavitation. A reduced stator blade count is also suggested due to a reduced TR loss and capacity loss at stall.

Evaluation of a Cyclone-Based Particulate Filtration System for High-Speed Diesel Engines

1994 ◽  
Vol 208 (4) ◽  
pp. 269-279 ◽  
Author(s):  
C Arcoumanis ◽  
L N Barbaris ◽  
R I Crane ◽  
P Wisby
Keyword(s):  
Diesel Engines ◽  
High Speed ◽  
Direct Injection ◽  
Operating Conditions ◽  
Exhaust Pipe ◽  
Filtration System ◽  
High Speed Diesel ◽  
Wide Range ◽  
Mass Flowrate ◽  
Particulate Filtration

A cyclone-based filtration system has been developed and its potential for reduction of exhaust particulates in high-speed direct injection diesel engines is evaluated; the filtration efficiency of the four cyclones has been enhanced by means of particulate agglomeration induced by cooling in a heat exchanger. With this system installed in the exhaust pipe of a 2.5 litre direct injection engine, tests covering a wide range of speed, load and exhaust gas recirculation (EGR) fraction resulted in reductions of up to 77 per cent in emitted particulate mass flowrate. The dependence of the system's performance on engine operating conditions, EGR configuration and cyclone geometry is presented and discussed.

Ball Bearing Response to Cage Unbalance

1986 ◽  
Vol 108 (3) ◽  
pp. 462-466 ◽  
Author(s):  
P. K. Gupta ◽  
J. F. Dill ◽  
J. W. Artuso ◽  
N. H. Forster
Keyword(s):  
Entire Range ◽  
High Speed ◽  
Ball Bearing ◽  
Operating Conditions ◽  
Angular Contact Ball Bearing ◽  
Turbine Engine ◽  
Wide Range ◽  
Inner Race ◽  
Good Agreement ◽  
Engine Bearing

Motion of the cage in a high-speed angular contact ball bearing is experimentally investigated as a function of prescribed unbalance, up to operating speeds corresponding to three million DN. The predictions of cage motion made by the recently developed computer model, ADORE, are validated in the light of the experimental data. It is shown the cage whirl velocity is essentially equal to its angular velocity at all levels of unbalance and over a wide range of operating conditions. For the inner race guided turbine engine bearing, the cage/race interaction takes place directly opposite to the location of the unbalance and the severity of the interaction increases with the level of unbalance and the operating speed. ADORE predictions, over the entire range of unbalance and bearing operating conditions, are in very good agreement with the experimental observations.

Sign in / Sign up

Export Citation Format

Share Document