Kinematic Analysis and Design of Kinematically Redundant Parallel Mechanisms

2004 ◽  
Vol 126 (1) ◽  
pp. 109-118 ◽  
Author(s):  
Jing Wang ◽  
Cle´ment M. Gosselin
Keyword(s):  
Kinematic Analysis ◽  
Main Idea ◽  
Parallel Manipulators ◽  
Singularity Analysis ◽  
Degree Of Freedom ◽  
Redundant Manipulators ◽  
Parallel Mechanisms ◽  
Jacobian Matrices ◽  
Kinematic Chains ◽  
Analysis And Design

This paper addresses the singularity analysis and the design of three new types of kinematically redundant parallel mechanisms, i.e., the four-degree-of-freedom planar and spherical parallel mechanisms and the seven-degree-of-freedom spatial Stewart platform. The main idea in the design of these parallel manipulators is the addition of one redundant degree of freedom in one of the kinematic chains of the nonredundant manipulator. Such manipulators can be used to avoid the singularities inside the workspace of nonredundant manipulators. After describing the geometry of the manipulators, the velocity equations are derived and the expressions for the Jacobian matrices are obtained. Then, the singularity conditions are discussed. Finally, the expressions of the singularity loci of the kinematically redundant mechanisms are obtained and the singularity loci of the nonredundant and redundant manipulators are compared. It is shown here that the conditions for the singularity of the redundant manipulators are reduced drastically relative to the nonredundant ones. As a result, the proposed kinematically redundant parallel manipulators may be of great interest in several applications.

A Novel Method on Singularity Analysis in Parallel Manipulators

2006 ◽  
Author(s):  
Hodjat Pendar ◽  
Maryam Mahnama ◽  
Hassan Zohoor
Keyword(s):  
Closed Loop ◽  
Parallel Manipulators ◽  
Singularity Analysis ◽  
Parallel Mechanisms ◽  
Kinematic Chains ◽  
Working Space ◽  
Novel Approach ◽  
Main Technique ◽  
Novel Method ◽  
Constraint Plane

A parallel manipulator is a closed loop mechanism in which a moving platform is connected to the base by at least two serial kinematic chains. The main problem engaged in these mechanisms, is their restricted working space as a result of singularities. In order to tackle these problems, many methods have been introduced by scholars. However, most of the mentioned methods are too much time consuming and need a great amount of computations. They also in most cases do not provide a good insight to the existence of singularity for the designer. In this paper a novel approach is introduced and utilized to identify singularities in parallel manipulators. By applying the new method, one could get a better understanding of geometrical interpretation of singularities in parallel mechanisms. Here we have introduced the Constraint Plane Method (CPM) and some of its applications in parallel mechanisms. The main technique used here, is based on Ceva Theorem.

scholarly journals Kinematic Analysis Of Tricept Parallel Manipulator

2012 ◽  
Vol 12 (5) ◽  
Author(s):  
Mir Amin Hosseini ◽  
Hamid-Reza Mohammadi Daniali
Keyword(s):  
Kinematic Analysis ◽  
Parallel Manipulator ◽  
Parallel Manipulators ◽  
Degree Of Freedom ◽  
Geometric Constraints ◽  
Design Parameters ◽  
Forward Kinematics ◽  
Jacobian Matrices ◽  
Moving Platforms ◽  
Workspace Optimization

Parallel manipulators consist of fixed and moving platforms connected to each other with some actuated links. They have some significant advantages over their serial counterparts. While, they suffer from relatively small workspaces, complex kinematics relations and highly singular points within their workspaces. In this paper, forward kinematics of Tricept parallel manipulator is solved analytically and its workspace optimization is performed. This parallel manipulator has a complex degree of freedom, therefore leads to dimensional in-homogeneous Jacobian matrices. Thus, we divide some entries of the Jacobian by units of length, thereby producing a new Jacobian that is dimensionally homogeneous. Moreover, its workspace is parameterized using some design parameters. Then, using GA method, the workspace is optimized subjects to some geometric constraints. Finally, dexterity of the design is evaluated. Keywords- Kinematic, Workspace, Singularity, TriceptABSTRAK - Manipulator selari terdiri daripada platform tetap dan bergerak yang bersambung antara satu sama lain dengan beberapa pautan bergerak. Manipulator selari mempunyai beberapa kebaikan tertentu dibandingkan dengan yang bersamaan dengannya. Walaupun ia mempunyai ruang kerja yang sempit, hubungan kinematik kompleks dan titik tunggal tinggi dalam linkungan ruang kerjanya. Dalam kajian ini, kinematik ke hadapan manipulator selari Tricept diselesaikan secara analisa dan pengoptimuman ruang kerja dijalankan. Manipulator selari ini mempunyai darjah kebebasan yang kompleks, yang menyebabkan ia mendorong kepada kehomogenan dimensi matriks Jacobian. Catatan Jacobian dibahagikan kepada unit panjang, dimana ia menghasilkan Jacobian baru yang homogen dimensinya. Tambahan, ruang kerjanya diparameterkan dengan menggunakan beberapa parameter reka bentuk. Kemudian, dengan kaedah GA, ruang kerja mengoptimakan subjek kepada beberapa kekangan geometrik. Akhirnya, kecakatan reka bentuk dinilaikan.Keywords- Kinematic, Workspace, Singularity, Tricept

scholarly journals Kinematic analysis of the X4 translational–rotational parallel robot

2018 ◽  
Vol 15 (5) ◽  
pp. 172988141880384 ◽  
Author(s):  
Stefan Staicu ◽  
Zhufeng Shao ◽  
Zhaokun Zhang ◽  
Xiaoqiang Tang ◽  
Liping Wang
Keyword(s):  
High Speed ◽  
Parallel Manipulators ◽  
Parallel Robot ◽  
Degree Of Freedom ◽  
Parallel Mechanisms ◽  
Kinematic Chains ◽  
Revolute Joints ◽  
Commercial Applications ◽  
Recursive Matrix ◽  
Singularity Locus

High-speed pick-and-place parallel manipulators have attracted considerable academic and industrial attention because of their numerous commercial applications. The X4 parallel robot was recently presented at Tsinghua University. This robot is a four-degree-of-freedom spatial parallel manipulator that consists of high-speed closed kinematic chains. Each of its limbs comprises an active pendulum and a passive parallelogram, which are connected to the end effector with other revolute joints. Kinematic issues of the X4 parallel robot, such as degree of freedom analysis, inverse kinematics, and singularity locus, are investigated in this study. Recursive matrix relations of kinematics are established, and expressions that determine the position, velocity, and acceleration of each robot element are developed. Finally, kinematic simulations of actuators and passive joints are conducted. The analysis and modeling methods illustrated in this study can be further applied to the kinematics research of other parallel mechanisms.

Design and Singularity Analysis of a 3-Translational-DOF In-Parallel Manipulator*

2002 ◽  
Vol 124 (3) ◽  
pp. 419-426 ◽  
Author(s):  
L. Romdhane ◽  
Z. Affi ◽  
M. Fayet
Keyword(s):  
Kinematic Analysis ◽  
Parallel Manipulator ◽  
Parallel Manipulators ◽  
Singularity Analysis ◽  
Orientation Error ◽  
Kinematic Chains ◽  
Prismatic Joints ◽  
Forward Kinematic ◽  
3D Solid ◽  
Novel Design

In this work, we shall present a novel design of a 3-translational-DOF in-parallel manipulator having 3 linear actuators. Three variable length legs constitute the actuators of this manipulator, whereas two other kinematic chains with passive joints are used to eliminate the three rotations of the platform with respect to the base. This design presents several advantages compared to other designs of similar 3-translational-dof parallel manipulators. First, the proposed design uses only revolute or spherical joints as passive joints and hence, it avoids problems that are inherent to the nature of prismatic joints when loaded in arbitrary way. Second, the actuators are chosen to be linear and to be located in the three legs since this design presents higher rigidity than other. In the second part of this paper, we addressed the problem of kinematic analysis of the proposed in-parallel manipulator. A mixed geometric and vector formulation is used to show that two solutions exist for the forward kinematic analysis. The problem of singularities is also investigated using the same method. In this work, we investigated the singularities of the active legs and the two types of singularity were identified: architectural singularities and configurational singularities. The singularity of the passive chains, used to restrict the motion of the platform to only three translations, is also investigated. In the last part of this paper, we built a 3D solid model of the platform and the amplitude of rotation due to the deformation of the different links under some realistic load was determined. This allowed us to estimate the “orientation error” of the platform due to external moments. Moreover, this analysis allowed us to compare the proposed design (over constrained) with a modified one (not over constrained). This comparison confirmed the conclusion that the over constraint design has a better rigidity.

Kinematic Analysis and Singularity Loci of Spatial Four-Degree-of-Freedom Parallel Manipulators Using a Vector Formulation

1998 ◽  
Vol 120 (4) ◽  
pp. 555-558 ◽  
Author(s):  
J. Wang ◽  
C. M. Gosselin
Keyword(s):  
Kinematic Analysis ◽  
Parallel Manipulators ◽  
Degree Of Freedom ◽  
New Method ◽  
Numerical Determination ◽  
Jacobian Matrices ◽  
Flight Simulators ◽  
Important Design ◽  
Robotic Applications

The kinematic analysis and the determination of the singularity loci of spatial four-degree-of-freedom parallel manipulators with prismatic or revolute actuators are discussed in this article. A new method for the derivation of the velocity equations and the corresponding Jacobian matrices is presented. The numerical determination of the workspace boundaries is then briefly discussed. Finally, the determination of the singularity loci is performed using the velocity equations and examples are given to illustrate the results obtained. Spatial four-degree-of-freedom parallel manipulators can be used in several robotic applications as well as in flight simulators. The determination of their singularity loci is a very important design issue.

Kinematic and Workspace Modelling of a 6-PUS Parallel Mechanism

2018 ◽  
Author(s):  
Jérôme Landuré ◽  
Clément Gosselin
Keyword(s):  
Kinematic Analysis ◽  
Parallel Mechanism ◽  
Inverse Kinematic ◽  
Degree Of Freedom ◽  
Accurate Description ◽  
Transmission Ratio ◽  
Inverse Kinematic Problem ◽  
Jacobian Matrices ◽  
Six Degree Of Freedom

This article presents the kinematic analysis of a six-degree-of-freedom six-legged parallel mechanism of the 6-PUS architecture. The inverse kinematic problem is recalled and the Jacobian matrices are derived. Then, an algorithm for the geometric determination of the workspace is presented, which yields a very fast and accurate description of the workspace of the mechanism. Singular boundaries and a transmission ratio index are then introduced and studied for a set of architectural parameters. The proposed analysis yields conceptual architectures whose properties can be adjusted to fit given applications.

Forward/Reverse Velocity and Acceleration Analysis for a Class of Lower-Mobility Parallel Mechanisms

2006 ◽  
Vol 129 (4) ◽  
pp. 390-396 ◽  
Author(s):  
Si J. Zhu ◽  
Zhen Huang ◽  
Hua F. Ding
Keyword(s):  
Kinematic Analysis ◽  
Jacobian Matrix ◽  
Hessian Matrix ◽  
Degree Of Freedom ◽  
Parallel Mechanisms ◽  
Analysis Method ◽  
Rear Part ◽  
Lower Mobility ◽  
Acceleration Analysis

This paper proposes a novel kinematic analysis method for a class of lower-mobility mechanisms whose degree-of-freedom (DoF) equal the number of single-DoF kinematic pairs in each kinematic limb if all multi-DoF kinematic pairs are substituted by the single one. For such an N-DoF (N<6) mechanism, this method can build a square (N×N) Jacobian matrix and cubic (N×N×N) Hessian matrix. The formulas in this method for different parallel mechanisms have unified forms and consequently the method is convenient for programming. The more complicated the mechanism is (for instance, the mechanism has more kinematic limbs or pairs), the more effective the method is. In the rear part of the paper, mechanisms 5-DoF 3-R(CRR) and 5-DoF 3-(RRR)(RR) are analyzed as examples.

Synthesis of 2T1R Decoupled Parallel Manipulators

2011 ◽  
Vol 308-310 ◽  
pp. 2025-2030 ◽  
Author(s):  
Wen Juan Lu ◽  
Li Jie Zhang ◽  
Da Xing Zeng ◽  
Ruo Song Wang
Keyword(s):  
Screw Theory ◽  
Control Design ◽  
Parallel Manipulators ◽  
Parallel Mechanisms ◽  
Type Synthesis ◽  
Precision Control ◽  
Kinematic Chains ◽  
Step Procedure ◽  
Nonlinear Relation ◽  
Three Degree Of Freedom

For the general parallel mechanisms(PMS), since the coupling between kinematic chains, the nonlinear relation between the input and output is presented, which have led to difficulty in the trajectory planning and precision control. Design of motion decoupled parallel mechanisms(DPMS) has become a good new topic in this area and has captured researcher's attention. In this work, the approach to a synthesis of three degree-of-freedom(3-DOF) DPMS is considered based on screw theory and motion synthesis ideas. Criterions for type synthesis of the branches for DPMS is established according to the twist screw system of the limbs, which assures the decoupling in each limb. Then a six-step procedure is presented for the type synthesis of 2T1R decoupled mechanisms.

Design and Mobility Analysis of Large Deployable Mechanisms Based on Plane-Symmetric Bricard Linkage

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
Xiaozhi Qi ◽  
Hailin Huang ◽  
Zhihuai Miao ◽  
Bing Li ◽  
Zongquan Deng
Keyword(s):  
Computer Aided Design ◽  
Closed Loop ◽  
Singularity Analysis ◽  
Degree Of Freedom ◽  
Plane Symmetric ◽  
Analysis And Design ◽  
Geometric Conditions ◽  
Deployable Mechanism ◽  
Vertical Bars ◽  
Aided Design

In this paper, a class of large deployable mechanisms constructed by plane-symmetric Bricard linkages is presented. The plane-symmetric Bricard linkage is a closed-loop overconstrained spatial mechanism composed of six hinge-jointed bars, which has one plane of symmetry during its deployment process. The kinematic analysis of the linkage is presented from the perspectives of geometric conditions, closure equations, and degree-of-freedom. The results illustrate that the linkage has one degree-of-freedom and can be deployed from the folded configuration to one rectangle plane. Therefore, the plane-symmetric Bricard linkage can be used as a basic deployable unit to construct larger deployable mechanisms. Four plane-symmetric Bricard linkages can be assembled into a quadrangular module by sharing the vertical bars of the adjacent units. The module is a multiloop deployable mechanism and has one degree-of-freedom. The singularity analysis of the module is developed, and two methods to avoid singularity are presented. A large deployable mast, deployable plane truss, and deployable ring are built with several plane-symmetric Bricard linkages. The deployment properties of the large deployable mechanisms are analyzed, and computer-aided design models for typical examples are built to illustrate their feasibility and validate the analysis and design methods.

Static Balancing of Spatial and Planar Parallel Manipulators With Prismatic Actuators

1998 ◽  
Author(s):  
Marc Leblond ◽  
Clément M. Gosselin
Keyword(s):  
Parallel Manipulators ◽  
Geometric Interpretation ◽  
Degree Of Freedom ◽  
Parallel Mechanisms ◽  
Static Balancing ◽  
Inertial Parameters ◽  
Dimensional Parameters ◽  
Balancing Conditions ◽  
Static Conditions ◽  
Planar Parallel Manipulators

Abstract In this paper, the static balancing of existing spatial and planar parallel manipulators by the addition of balancing elements is addressed. Static balancing is defined here as the set of conditions on manipulator dimensional and inertial parameters which, when satisfied, ensure that the weight of the links does not produce any force (or torque) at the actuators for any configuration of the manipulator, under static conditions. These conditions are derived here for spatial six-degree-of-freedom parallel manipulators and it is shown that planar three-degree-of-freedom parallel manipulators can be treated as a particular case of the spatial 6-dof mechanisms. The static balancing conditions associated with planar mechanisms can therefore easily be found, but are not given here because of space limitations. A brief geometric interpretation of the balancing conditions which are associated with statically balanced spatial mechanisms is then carried out. It is shown that balancing is generally possible even when the dimensional parameters are imposed, which is a useful property since dimensional parameters are usually obtained from kinematic design or optimization. Finally, examples of balanced planar and spatial parallel manipulators are given. Static balancing leads to considerable reduction in the actuator forces (or torques), which in turn leads to less powerful actuators and more efficient designs. Moreover, the possibility of balancing existing systems by introducing additional elements, as demonstrated here, is of interest for retrofitting existing parallel mechanisms.

Sign in / Sign up

Export Citation Format

Share Document