Measurements of Resistance of Individual Square-Mesh Screens to Oscillating Flow at Low and Intermediate Reynolds Numbers

2003 ◽  
Vol 125 (5) ◽  
pp. 851-862 ◽  
Author(s):  
Ray Scott Wakeland ◽  
Robert M. Keolian
Keyword(s):  
Reynolds Number ◽  
Friction Factor ◽  
Steady Flow ◽  
Oscillation Amplitude ◽  
Low Frequency ◽  
Reynolds Numbers ◽  
Oscillating Flow ◽  
Pressure Losses ◽  
Approach Velocity ◽  
Flow Resistances

Measurements are reported of pressure losses across single screens subjected to low-frequency oscillating flow for 0.002≲Red≲400, where Red is Reynolds number based on wire diameter and peak approach velocity. Several correlation methods are examined. Extensive comparisons are made between present oscillating-flow results and previous reports of the resistance of screens to steady flow. Defining oscillating results in terms of peak amplitudes, the oscillating and steady-flow resistances are found to be the same, including behavior in the intermediate Reynolds number region that departs from correlations of the form ARe−1+B. The friction factor is also found to depend on Reynolds number, but not independently on oscillation amplitude, over the range of conditions measured.

Local Pressure Measurement of Gaseous Flow Through Microchannels

1999 ◽  
Author(s):  
Stephen E. Turner ◽  
Hongwei Sun ◽  
Mohammad Faghri ◽  
Otto J. Gregory
Keyword(s):  
Reynolds Number ◽  
Pressure Distribution ◽  
Friction Factor ◽  
Knudsen Number ◽  
Flow Region ◽  
Reynolds Numbers ◽  
Helium Flow ◽  
Local Pressure ◽  
Pressure Losses ◽  
Flow Through

Abstract This paper presents an experimental investigation on nitrogen and helium flow in microchannels etched in silicon with hydraulic diameters of 9.7, 19.6, and 46.6 μm, and Reynolds numbers ranging from 0. 2 to 1000. The objectives of this research are (1) to measure the pressure distribution along the length of a microchannel; and (2) to determine the friction factor within the fully developed region of the microchannel. The pressure distribution is presented as absolute local pressure plotted against the distance from the microchannel inlet. The friction factor results are presented as the product of friction factor and Reynolds number plotted against Reynolds number with the outlet Knudsen number, Kn, as a curve parameter. The following conclusions have been reached in the present investigation: (1) Pressure losses at the microchannel entrance can be significant; (2) the product, f*Re, when measured sufficiently far away from the entrance and exit is a constant in the laminar flow region; and (3) the friction factor decreases as the Knudsen number increases.

Flow Characteristics of Oscillating Flow in a Channel Obstructed by an Array of Circular Cylinders

2000 ◽  
Author(s):  
Ken-ichi Sawada ◽  
Hiroyuki Murata ◽  
Michiyuki Kobayashi
Keyword(s):  
Reynolds Number ◽  
Steady Flow ◽  
Strouhal Number ◽  
Oscillation Amplitude ◽  
Flow Characteristics ◽  
Circular Cylinders ◽  
Oscillating Flow ◽  
Mean Velocity ◽  
Cross Sectional ◽  
Flow Experiments

Abstract Flow visualization experiments on oscillating flow in a channel obstructed by an array of circular cylinders were performed. First of all, steady flow experiments without oscillation were carried out. The Karman vortices began to shed in a range of the Reynolds number: 53<Re<68. The Strouhal number showed a tendency to decrease with an increase of the Reynolds number. Oscillating flow experiments were carried out secondly. When the oscillation amplitude was small, Karman vortices shed periodically and its Strouhal number agreed with that in the steady flow. But, when the oscillation amplitude was large, shedding of Karman vortex was well controlled by the oscillating flow. The vortex shedding frequency became large with an increase of the cross-sectional mean velocity. On the other hand, the amplitude of velocity fluctuation in the wake was small in the accelerating phase and large in the decelerating phase.

scholarly journals Turbulence model performance for ventilation components pressure losses

2021 ◽  
Author(s):  
Karsten Tawackolian ◽  
Martin Kriegel
Keyword(s):  
Reynolds Number ◽  
Turbulence Model ◽  
Pressure Loss ◽  
Low Reynolds Number ◽  
Turbulence Models ◽  
Reynolds Numbers ◽  
Test Case ◽  
Pressure Losses ◽  
Loss Coefficients ◽  
Near Wall

AbstractThis study looks to find a suitable turbulence model for calculating pressure losses of ventilation components. In building ventilation, the most relevant Reynolds number range is between 3×104 and 6×105, depending on the duct dimensions and airflow rates. Pressure loss coefficients can increase considerably for some components at Reynolds numbers below 2×105. An initial survey of popular turbulence models was conducted for a selected test case of a bend with such a strong Reynolds number dependence. Most of the turbulence models failed in reproducing this dependence and predicted curve progressions that were too flat and only applicable for higher Reynolds numbers. Viscous effects near walls played an important role in the present simulations. In turbulence modelling, near-wall damping functions are used to account for this influence. A model that implements near-wall modelling is the lag elliptic blending k-ε model. This model gave reasonable predictions for pressure loss coefficients at lower Reynolds numbers. Another example is the low Reynolds number k-ε turbulence model of Wilcox (LRN). The modification uses damping functions and was initially developed for simulating profiles such as aircraft wings. It has not been widely used for internal flows such as air duct flows. Based on selected reference cases, the three closure coefficients of the LRN model were adapted in this work to simulate ventilation components. Improved predictions were obtained with new coefficients (LRNM model). This underlined that low Reynolds number effects are relevant in ventilation ductworks and give first insights for suitable turbulence models for this application. Both the lag elliptic blending model and the modified LRNM model predicted the pressure losses relatively well for the test case where the other tested models failed.

Numerical and Experimental Analysis of Turbulent Flow in Corrugated Pipes

2010 ◽  
Vol 132 (7) ◽  
Author(s):  
Henrique Stel ◽  
Rigoberto E. M. Morales ◽  
Admilson T. Franco ◽  
Silvio L. M. Junqueira ◽  
Raul H. Erthal ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Pressure Drop ◽  
Turbulent Flow ◽  
Friction Factor ◽  
Turbulence Models ◽  
Reynolds Numbers ◽  
Velocity Magnitude ◽  
Geometric Configurations ◽  
Corrugated Surfaces ◽  
Friction Factors

This article describes a numerical and experimental investigation of turbulent flow in pipes with periodic “d-type” corrugations. Four geometric configurations of d-type corrugated surfaces with different groove heights and lengths are evaluated, and calculations for Reynolds numbers ranging from 5000 to 100,000 are performed. The numerical analysis is carried out using computational fluid dynamics, and two turbulence models are considered: the two-equation, low-Reynolds-number Chen–Kim k-ε turbulence model, for which several flow properties such as friction factor, Reynolds stress, and turbulence kinetic energy are computed, and the algebraic LVEL model, used only to compute the friction factors and a velocity magnitude profile for comparison. An experimental loop is designed to perform pressure-drop measurements of turbulent water flow in corrugated pipes for the different geometric configurations. Pressure-drop values are correlated with the friction factor to validate the numerical results. These show that, in general, the magnitudes of all the flow quantities analyzed increase near the corrugated wall and that this increase tends to be more significant for higher Reynolds numbers as well as for larger grooves. According to previous studies, these results may be related to enhanced momentum transfer between the groove and core flow as the Reynolds number and groove length increase. Numerical friction factors for both the Chen–Kim k-ε and LVEL turbulence models show good agreement with the experimental measurements.

Heat Transfer And Pressure Drop Of An Angled Discrete Turbulator At Elevated Reynolds Numbers Up To 900,000

2021 ◽  
pp. 1-29
Author(s):  
Sam Ghazi-Hesami ◽  
Dylan Wise ◽  
Keith Taylor ◽  
Peter Ireland ◽  
Étienne Robert
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Friction Factor ◽  
Rectangular Channel ◽  
Reynolds Numbers ◽  
Enhance Heat Transfer ◽  
Near Surface ◽  
Number Range ◽  
Smooth Channel

Abstract Turbulators are a promising avenue to enhance heat transfer in a wide variety of applications. An experimental and numerical investigation of heat transfer and pressure drop of a broken V (chevron) turbulator is presented at Reynolds numbers ranging from approximately 300,000 to 900,000 in a rectangular channel with an aspect ratio (width/height) of 1.29. The rib height is 3% of the channel hydraulic diameter while the rib spacing to rib height ratio is fixed at 10. Heat transfer measurements are performed on the flat surface between ribs using transient liquid crystal thermography. The experimental results reveal a significant increase of the heat transfer and friction factor of the ribbed surface compared to a smooth channel. Both parameters increase with Reynolds number, with a heat transfer enhancement ratio of up to 2.15 (relative to a smooth channel) and a friction factor ratio of up to 6.32 over the investigated Reynolds number range. Complementary CFD RANS (Reynolds-Averaged Navier-Stokes) simulations are performed with the κ-ω SST turbulence model in ANSYS Fluent® 17.1, and the numerical estimates are compared against the experimental data. The results reveal that the discrepancy between the experimentally measured area averaged Nusselt number and the numerical estimates increases from approximately 3% to 13% with increasing Reynolds number from 339,000 to 917,000. The numerical estimates indicate turbulators enhance heat transfer by interrupting the boundary layer as well as increasing near surface turbulent kinetic energy and mixing.

Effect of Surface Roughness on Gaseous Flow Through Microchannels

2000 ◽  
Author(s):  
Stephen E. Turner ◽  
Hongwei Sun ◽  
Mohammad Faghri ◽  
Otto J. Gregory
Keyword(s):  
Surface Roughness ◽  
Reynolds Number ◽  
Friction Factor ◽  
Reynolds Numbers ◽  
Helium Flow ◽  
Local Pressure ◽  
Aspect Ratios ◽  
Corrugated Surfaces ◽  
Flow Through ◽  
Effect Of Surface

Abstract This paper presents an experimental investigation on nitrogen and helium flow through microchannels etched in silicon with hydraulic diameters between 10 and 40 microns, and Reynolds numbers ranging from 0.3 to 600. The objectives of this research are (1) to fabricate microchannels with uniform surface roughness and local pressure measurement; (2) to determine the friction factor within the locally fully developed region of the microchannel; and (3) to evaluate the effect of surface roughness on momentum transfer by comparison with smooth microchannels. The friction factor results are presented as the product of friction factor and Reynolds number plotted against Reynolds number. The following conclusions have been reached in the present investigation: (1) microchannels with uniform corrugated surfaces can be fabricated using standard photolithographic processes; and (2) surface features with low aspect ratios of height to width have little effect on the friction factor for laminar flow in microchannels.

Friction Factor Behavior From Flat-Plate Tests of 12.15 mm Diameter Hole-Pattern Roughened Surfaces

2011 ◽  
Author(s):  
Thanesh Deva Asirvatham ◽  
Dara W. Childs ◽  
Stephen Phillips
Keyword(s):  
Reynolds Number ◽  
Flat Plate ◽  
Friction Factor ◽  
Dynamic Pressure ◽  
Reynolds Numbers ◽  
Stagnation Temperature ◽  
Flat Plates ◽  
Number Range ◽  
Current Test ◽  
Rough Plate

A flat-plate tester is used to measure the friction-factor behavior for a hole-pattern-roughened surface facing a smooth surface with compressed air as the medium. Measurements of mass flow rate, static pressure drop and stagnation temperature are carried out and used to find a combined (stator + rotor) Fanning friction factor value. In addition, dynamic pressure measurements are made at four axial locations at the bottom of individual holes of the rough plate and at facing locations in the smooth plate. The description of the test rig and instrumentation, and the procedure of testing and calculation are explained in detail in Kheireddin in 2009 and Childs et al. in 2010. Three hole-pattern flat-plates with a hole-pattern diameter of 12.15 mm were tested having depths of 0.9, 1.9, and 2.9 mm. Tests were done with clearances at 0.254, 0.381, and 0.653 mm, and inlet pressures of 56, 70 and 84 bar for a range of pressure ratios, yielding a Reynolds-number range of 100,000 to 800,000. The effects of Reynolds number, clearance, inlet pressure, and hole depth on friction factor are studied. The data are compared to friction factor values of three hole-pattern flat-plates with 3.175 mm diameter holes with hole depths of 1.9, 2.6, and 3.302 mm tested in the same rig described by Kheireddin in 2009. The test program was initiated mainly to investigate a “friction-factor jump” phenomenon cited by Ha et al. in 1992 in test results from a flat-plate tester using facing hole-pattern plates where, at elevated values of Reynolds numbers, the friction factor began to increase steadily with increasing Reynolds numbers. Friction-factor jump was not observed in any of the current test cases.

Unsteady flow about a sphere at low to moderate Reynolds number. Part 1. Oscillatory motion

1994 ◽  
Vol 277 ◽  
pp. 347-379 ◽  
Author(s):  
Eugene J. Chang ◽  
Martin R. Maxey
Keyword(s):  
Reynolds Number ◽  
Unsteady Flow ◽  
Steady Flow ◽  
Oscillatory Flow ◽  
Reynolds Numbers ◽  
Oscillatory Motion ◽  
Rigid Sphere ◽  
Flow Conditions ◽  
Steady Streaming ◽  
Moderate Reynolds Number

A direct numerical simulation, based on spectral methods, has been used to compute the time-dependent, axisymmetric viscous flow past a rigid sphere. An investigation has been made for oscillatory flow about a zero mean for different Reynolds numbers and frequencies. The simulation has been verified for steady flow conditions, and for unsteady flow there is excellent agreement with Stokes flow theory at very low Reynolds numbers. At moderate Reynolds numbers, around 20, there is good general agreement with available experimental data for oscillatory motion. Under steady flow conditions no separation occurs at Reynolds number below 20; however in an oscillatory flow a separation bubble forms on the decelerating portion of each cycle at Reynolds numbers well below this. As the flow accelerates again the bubble detaches and decays, while the formation of a new bubble is inhibited till the flow again decelerates. Steady streaming, observed for high frequencies, is also observed at low frequencies due to the flow separation. The contribution of the pressure to the resultant force on the sphere includes a component that is well described by the usual added-mass term even when there is separation. In a companion paper the flow characteristics for constant acceleration or deceleration are reported.

Analyses of Liquid Flow in Micro-Conduits

2004 ◽  
Author(s):  
Junemo Koo ◽  
Clement Kleinstreuer
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Friction Factor ◽  
Viscous Dissipation ◽  
Wall Slip ◽  
Reynolds Numbers ◽  
Darcy Number ◽  
Low Reynolds Numbers ◽  
Dissipation Effect ◽  
Liquid Flows

Experimental observations of liquid microchannel flow are reviewed and results of computer experiments concerning channel entrance, wall slip, non-Newtonian fluid, surface roughness, viscous dissipation and flow instability effects on the friction factor are discussed Specifically, based on numerical friction factor analyses, the entrance effect should be taken into account for any microfluidic system. It is a function of channel length, aspect ratio and the Reynolds number. Non-Newtonian fluid flow effects are expected to be important for polymeric liquids and dense particle suspension flows. The wall-slip effect is negligible for liquid flows. For relatively low Reynolds numbers, i.e., Re > 1,200, onset to instabilities may have to be considered because of possible geometric non-uniformities, including a contraction and/or bend at the microchannel inlet as well as substantial surface roughness. Significant roughness effects, described with a new porous medium layer (PML) model, are a function of the Darcy number, the Reynolds number and cross-sectional configurations. This model was applied to micro-scale liquid flows in straight channels, tubes and rotating cylinders, and validated with experimental data sets. In contrast to published models, PML model simulations yield both an increase and decrease of the friction factor depending on the Darcy number. Viscous dissipation in microchannels is a strong function of the channel aspect ratio, Reynolds number, Eckert number, Prandtl number, and conduit hydraulic diameter. Specifically, viscous dissipation effects are quite important for fluids with low specific heat capacities and high viscosities, even for very low Reynolds numbers, i.e., ReD < 1. The viscous dissipation effect was found to decrease as the fluid temperature increases. As the aspect ratio deviates from unity, the viscous dissipation effect increases. It was found that ignoring the viscous dissipation effect could ultimately affect friction factor measurements for flows in micro-conduits. This could imply a significant amount of viscous heat generation and, for example, may diminish a projected micro-heat-exchanger performance.

Sign in / Sign up

Export Citation Format

Share Document