Subsonic Elector Nozzle Limiting Flow Conditions

2003 ◽  
Vol 125 (3) ◽  
pp. 851-854 ◽  
Author(s):  
L. J. De Chant
Keyword(s):  
Design Space ◽  
Reverse Flow ◽  
Control Volume ◽  
Flow Conditions ◽  
Efficient Tool ◽  
One Dimensional ◽  
Choked Flow ◽  
Ejector Nozzle ◽  
Classical Control ◽  
Good Agreement

This paper describes an analytical method used to provide information concerning limiting flows for subsonic ejector nozzles. Three potential limiting flows have been identified and modeled using reduced control volume based analysis: (1) incipient reverse flow into the secondary inlet, (2) choked flow in the secondary inlet, and (3) choked flow in the exit mixing stream. Comparison of the methods developed here with the classical control volume portion of an ejector nozzle code have been performed and show good agreement. As such, it is concluded, that within the scope of one-dimensional control-volume based computations, that the methods developed here provide an efficient tool to help delimit the design space acceptable for ejector operation.

The Effect of Silencers of the Helmholtz-Resonator Type on Pressure Waves of Finite Amplitude: Single Pressure Pulses

1974 ◽  
Vol 16 (4) ◽  
pp. 268-275 ◽  
Author(s):  
G. H. Trengrouse
Keyword(s):  
Incident Wave ◽  
Helmholtz Resonator ◽  
Single Pulse ◽  
Finite Amplitude ◽  
Pressure Waves ◽  
Flow Conditions ◽  
Partial Reflection ◽  
One Dimensional ◽  
The Relationship ◽  
Good Agreement

The attenuation of large-amplitude waves effected by silencers of the so-called Helmholtz-resonator type is envisaged as being due to the finite efflux of gas through the holes of the silencer with resulting partial reflection, and hence reduced transmission, of the incident wave. Quasi-steady, one-dimensional flow arguments are used to predict the attenuation, the flow conditions being assumed reversible and adiabatic, that is, isentropic. This latter assumption is avoided in an alternative method by assuming a knowledge of the relationship between pipe Mach numbers and the pressure difference in the pipe across the holes. Indicator diagrams resulting from single pulse experiments are, in general, in good agreement with those predicted.

Sizing Safety Valve Vent Pipes for Saturated Steam

1982 ◽  
Vol 104 (1) ◽  
pp. 247-251
Author(s):  
H. E. Brandmaier
Keyword(s):  
Ideal Gas ◽  
Gas Analysis ◽  
Saturated Steam ◽  
Flow Conditions ◽  
Flow Properties ◽  
Pipe Length ◽  
One Dimensional ◽  
Choked Flow ◽  
Pipe Outlet ◽  
Orifice Valve

An earlier one-dimensional ideal gas analysis was changed to incorporate equilibrium properties of steam as given by the 1967 ASME steam tables. A generalized procedure based on pressure and entropy as independent variables is used to calculate choked flow conditions at the valve orifice, valve pipe outlet and vent pipe outlet. At the third location, the results are independent of whether flow in the vent pipe is supersonic or subsonic. An integral method is used to calculate the vent pipe length required to choke the flow. Computed data are compared with ideal gas data. The vent pipe size, to prevent blowback into the powerplant, is less conservative using real steam data. The flow properties, particularly specific volume, are significantly different.

scholarly journals Mechanisms and Countermeasures on Sediment and Wood Damage in Sediment Retarding Basins

Water ◽  
2021 ◽  
Vol 13 (22) ◽  
pp. 3283
Author(s):  
Norio Harada ◽  
Kana Nakatani ◽  
Ichiro Kimura ◽  
Yoshifumi Satofuka ◽  
Takahisa Mizuyama
Keyword(s):  
Debris Flow ◽  
Flood Damage ◽  
Bed Load ◽  
Dimensional Model ◽  
Flow Conditions ◽  
One Dimensional ◽  
Wood Debris ◽  
Debris Transport ◽  
Sediment Flow ◽  
Good Agreement

Improvements in sediment retarding basin design are required to mitigate flood damage caused by bed load and wood debris outflow in lower river reaches. We used a scaled sediment retarding basin model to optimize our basin design, with the goal of improving sediment and wood debris transport and capture. Changes to the structural dimensions and elements of the sediment retarding basin were assessed under experimental debris flow conditions. The results obtained from the experiments and simulations were in good agreement regarding sediment flow and containment. The proposed one-dimensional model is useful for showing the effects of flow conditions within a sediment retarding basin on sediment transport.

Effect of leakage and blockage on the acoustic behavior of particle filters

2019 ◽  
Vol 67 (6) ◽  
pp. 483-492
Author(s):  
Seonghyeon Baek ◽  
Iljae Lee
Keyword(s):  
Transfer Matrix ◽  
Particle Filters ◽  
Acoustic Analysis ◽  
Transmission Loss ◽  
One Dimensional ◽  
Filter System ◽  
The Difference ◽  
The One ◽  
Analytical Approaches ◽  
Good Agreement

The effects of leakage and blockage on the acoustic performance of particle filters have been examined by using one-dimensional acoustic analysis and experimental methods. First, the transfer matrix of a filter system connected to inlet and outlet pipes with conical sections is measured using a two-load method. Then, the transfer matrix of a particle filter only is extracted from the experiments by applying inverse matrices of the conical sections. In the analytical approaches, the one-dimensional acoustic model for the leakage between the filter and the housing is developed. The predicted transmission loss shows a good agreement with the experimental results. Compared to the baseline, the leakage between the filter and housing increases transmission loss at a certain frequency and its harmonics. In addition, the transmission loss for the system with a partially blocked filter is measured. The blockage of the filter also increases the transmission loss at higher frequencies. For the simplicity of experiments to identify the leakage and blockage, the reflection coefficients at the inlet of the filter system have been measured using two different downstream conditions: open pipe and highly absorptive terminations. The experiments show that with highly absorptive terminations, it is easier to see the difference between the baseline and the defects.

Modeling of mass transfer in biofilms in oscillatory flow conditions using k-ɛ turbulence model

2003 ◽  
Vol 3 (1-2) ◽  
pp. 201-207
Author(s):  
H. Nagaoka ◽  
T. Nakano ◽  
D. Akimoto
Keyword(s):  
Numerical Simulation ◽  
Mass Transfer ◽  
Turbulence Model ◽  
Uptake Rate ◽  
Oscillatory Flow ◽  
Substrate Uptake ◽  
Flow Conditions ◽  
Mass Transfer Mechanism ◽  
Substrate Uptake Rate ◽  
Good Agreement

The objective of this research is to investigate mass transfer mechanism in biofilms under oscillatory flow conditions. Numerical simulation of turbulence near a biofilm was conducted using the low Reynold’s number k-ɛ turbulence model. Substrate transfer in biofilms under oscillatory flow conditions was assumed to be carried out by turbulent diffusion caused by fluid movement and substrate concentration profile in biofilm was calculated. An experiment was carried out to measure velocity profile near a biofilm under oscillatory flow conditions and the influence of the turbulence on substrate uptake rate by the biofilm was also measured. Measured turbulence was in good agreement with the calculated one and the influence of the turbulence on the substrate uptake rate was well explained by the simulation.

PHOTOINDUCED NONLINEAR OCTUPOLAR POLARIZATION: TRANSIENT AND PERMANENT REGIMES

1996 ◽  
Vol 05 (04) ◽  
pp. 653-670 ◽  
Author(s):  
CÉLINE FIORINI ◽  
JEAN-MICHEL NUNZI ◽  
FABRICE CHARRA ◽  
IFOR D.W. SAMUEL ◽  
JOSEPH ZYSS
Keyword(s):  
Theoretical Analysis ◽  
Second Harmonic ◽  
Experimental Results ◽  
Polar Field ◽  
Rotational Spectrum ◽  
Dual Frequency ◽  
One Dimensional ◽  
Ethyl Violet ◽  
Disperse Red 1 ◽  
Good Agreement

An original poling method using purely optical means and based on a dual-frequency interference process is presented. We show that the coherent superposition of two beams at fundamental and second-harmonic frequencies results in a polar field with an irreducible rotational spectrum containing both a vector and an octupolar component. This enables the method to be applied even to molecules without a permanent dipole such as octupolar molecules. After a theoretical analysis of the process, we describe different experiments aiming at light-induced noncentrosymmetry performed respectively on one-dimensional Disperse Red 1 and octupolar Ethyl Violet molecules. Macroscopic octupolar patterning of the induced order is demonstrated in both transient and permanent regimes. Experimental results show good agreement with theory.

scholarly journals Optimization of the flow conditions in the spawning ground of the Chinese sturgeon (Acipenser sinensis) through Gezhouba Dam generating units

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Anyang Huang ◽  
Jinzhong Yao ◽  
Jiazhi Zhu ◽  
Xingchen Gao ◽  
Wei Jiang
Keyword(s):  
Spawning Ground ◽  
Chinese Sturgeon ◽  
Flow Conditions ◽  
Velocity Measurements ◽  
Acipenser Sinensis ◽  
Critically Endangered Species ◽  
Gezhouba Dam ◽  
Opening Mode ◽  
Suitable Area ◽  
Good Agreement

AbstractChinese sturgeon (Acipenser sinensis) is a critically endangered species, and waters downstream from Gezhouba Dam are the only known spawning ground. To optimize the velocity conditions in the spawning ground by controlling the opening mode of Gezhouba Dam generator units, a mathematical model of Chinese sturgeon spawning ground was established in FLOW-3D. The model was evaluated with velocity measurements, and the results were determined to be in good agreement. By inverting the 2016–2019 field monitoring results, the model shows that the preferred velocity range for Chinese sturgeon spawning is 0.6–1.5 m/s. Velocity fields of different opening modes of the generator units were simulated with identical discharge. The suitable-velocity area was maximal when all units of Dajiang Plant of Gezhouba Dam were open. For discharges below 12,000 m3/s, most of the area was suitable; for discharges above 12,000 m3/s, the suitable area rapidly decreased with increasing discharge. A comparison of suitable areas under high-flow showed that at discharges of 12,000–15,000 m3/s, opening 11–13 units on the left side was optimal. For discharges above 15,000 m3/s, all units should be open. We used these results to recommend a new operation scheme to support the conservation of Chinese sturgeon.

Diabatic Nozzle Flow with Constant Small Stage Efficiency

1960 ◽  
Vol 64 (598) ◽  
pp. 632-635 ◽  
Author(s):  
R. A. A. Bryant
Keyword(s):  
Gas Flow ◽  
Nozzle Flow ◽  
Flow Conditions ◽  
One Dimensional ◽  
Real Flow ◽  
Stage Efficiency ◽  
Frictional Effects

The concept of small stage efficiency is introduced when studying one-dimensional gas flow in nozzles in order to permit a closer approximation of real flow conditions than is possible from an isentropic analysis. It is more or less conventional to assume the flow conditions are adiabatic whenever the small stage efficiency is used. That is to say, small stage efficiency is generally considered in relation to flows contained within adiabatic boundaries, in which case it becomes a measure of the heat generated by internal frictional effects alone.

A Model for Predicting Temperature of Electrofusion Joints for Polyethylene Pipes

2009 ◽  
Vol 131 (6) ◽  
Author(s):  
Jianfeng Shi ◽  
Jinyang Zheng ◽  
Weican Guo ◽  
Ping Xu ◽  
Yongquan Qin ◽  
...  
Keyword(s):  
Thermal Contact ◽  
Power Input ◽  
Ultrasonic Test ◽  
Thermal Contact Conductance ◽  
Transfer Model ◽  
Contact Conductance ◽  
One Dimensional ◽  
Polyethylene Pipes ◽  
Heating Wire ◽  
Good Agreement

With the increasing application of electrofusion (EF) welding in connecting polyethylene (PE) pipes for gas distribution, more effort has been invested to ensure the safety of the pipeline systems. The objective of this paper is to investigate and understand the temperature distribution during EF welding. A one-dimensional transient heat-transfer model was proposed, taking the variation in the rate of power input, the phase transition of PE, and the thermal contact conductance between heating wire and PE into consideration. Then, experiments were designed to verify the power input and the temperature. The measured values of the power input were shown to be in good agreement with the analytical results. Based on ultrasonic test (UT), a new “Eigen-line” method was presented, which overcomes the difficulties found in the thermocouples’ temperature measurements. The results demonstrate good agreements between prediction and experiment. Finally, based on the presented model, a detailed parametric study was carried out to investigate the influences of the variation in the power input, the physical properties of PE, and the thermal contact conductance between heating wire and surrounding PE.

scholarly journals An approach to the modeling of a virtual thermal manikin

2014 ◽  
Vol 18 (4) ◽  
pp. 1413-1423 ◽  
Author(s):  
Dragan Ruzic ◽  
Sinisa Bikic
Keyword(s):  
Turbulence Models ◽  
Thermal Conditions ◽  
Heat Fluxes ◽  
Thermal Manikin ◽  
Flow Conditions ◽  
Body Segments ◽  
Nominal Size ◽  
Natural Flow ◽  
Good Agreement ◽  
Made In

The aim of the research described in this paper, is to make a virtual thermal manikin that would be simple, but also robust and reliable. The virtual thermal manikin was made in order to investigate thermal conditions inside vehicle cabins. The main parameters of the presented numerical model that were investigated in this paper are mesh characteristics and turbulence models. Heat fluxes on the manikin's body segments obtained from the simulations were compared with published results, from three different experiments done on physical thermal manikins. The presented virtual thermal manikin, meshed with surface elements of 0.035 m in nominal size (around 13,600 surface elements) and in conjunction with the two-layer RANS Realizable k-? turbulence model, had generally good agreement with experimental data in both forced and natural flow conditions.

Sign in / Sign up

Export Citation Format

Share Document