Rolls Royce/Allison 501-K Gas Turbine Antifouling Compressor Coatings Evaluation

2003 ◽  
Vol 125 (3) ◽  
pp. 482-488 ◽  
Author(s):  
Daniel E. Caguiat
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
Gas Turbines ◽  
Performance Degradation ◽  
Specific Fuel Consumption ◽  
Inlet Temperature ◽  
Test Results ◽  
Turbine Inlet ◽  
Compressor Performance ◽  
Compressor Efficiency

The Naval Surface Warfare Center, Carderock Division (NSWCCD) Gas Turbine Emerging Technologies Code 9334 was tasked by NSWCCD Shipboard Energy Office Code 859 to research and evaluate fouling resistant compressor coatings for Rolls Royce Allison 501-K Series gas turbines. The objective of these tests was to investigate the feasibility of reducing the rate of compressor fouling degradation and associated rate of specific fuel consumption (SFC) increase through the application of anti-fouling coatings. Code 9334 conducted a market investigation and selected coatings that best fit the test objective. The coatings selected were Sermalon for compressor stages 1 and 2 and Sermaflow S4000 for the inlet guide vanes and remaining 12 compressor stages. Both coatings are manufactured by Sermatech International, are intended to substantially decrease blade surface roughness, have inert top layers, and contain an anti-corrosive aluminum-ceramic base coat. Sermalon contains a Polytetrafluoroethylene (PTFE) topcoat, a substance similar to Teflon, for added fouling resistance. Tests were conducted at the Philadelphia Land Based Engineering Site (LBES). Testing was first performed on the existing LBES 501-K17 gas turbine, which had an uncoated compressor. The compressor was then replaced by a coated compressor and the test was repeated. The test plan consisted of injecting a known amount of salt solution into the gas turbine inlet while gathering compressor performance degradation and fuel economy data for 0, 500, 1000, and 1250 KW generator load levels. This method facilitated a direct comparison of compressor degradation trends for the coated and uncoated compressors operating with the same turbine section, thereby reducing the number of variables involved. The collected data for turbine inlet, temperature, compressor efficiency, and fuel consumption were plotted as a percentage of the baseline conditions for each compressor. The results of each plot show a decrease in the rates of compressor degradation and SFC increase for the coated compressor compared to the uncoated compressor. Overall test results show that it is feasible to utilize antifouling compressor coatings to reduce the rate of specific fuel consumption increase associated with compressor performance degradation.

Rolls Royce/Allison 501-K Gas Turbine Anti-Fouling Compressor Coatings Evaluation

2002 ◽  
Author(s):  
Daniel E. Caguiat
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
Gas Turbines ◽  
Performance Degradation ◽  
Specific Fuel Consumption ◽  
Inlet Temperature ◽  
Test Results ◽  
Turbine Inlet ◽  
Compressor Performance ◽  
Compressor Efficiency

The Naval Surface Warfare Center, Carderock Division (NSWCCD) Gas Turbine Emerging Technologies Code 9334 was tasked by NSWCCD Shipboard Energy Office Code 859 to research and evaluate fouling resistant compressor coatings for Rolls Royce Allison 501-K Series gas turbines. The objective of these tests was to investigate the feasibility of reducing the rate of compressor fouling degradation and associated rate of specific fuel consumption (SFC) increase through the application of anti-fouling coatings. Code 9334 conducted a market investigation and selected coatings that best fit the test objective. The coatings selected were Sermalon for compressor stages 1 and 2 and Sermaflow S4000 for the remaining 12 compressor stages. Both coatings are manufactured by Sermatech International, are intended to substantially decrease blade surface roughness, have inert top layers, and contain an anti-corrosive aluminum-ceramic base coat. Sermalon contains a Polytetrafluoroethylene (PTFE) topcoat, a substance similar to Teflon, for added fouling resistance. Tests were conducted at the Philadelphia Land Based Engineering Site (LBES). Testing was first performed on the existing LBES 501-K17 gas turbine, which had a non-coated compressor. The compressor was then replaced by a coated compressor and the test was repeated. The test plan consisted of injecting a known amount of salt solution into the gas turbine inlet while gathering compressor performance degradation and fuel economy data for 0, 500, 1000, and 1250 KW generator load levels. This method facilitated a direct comparison of compressor degradation trends for the coated and non-coated compressors operating with the same turbine section, thereby reducing the number of variables involved. The collected data for turbine inlet, temperature, compressor efficiency, and fuel consumption were plotted as a percentage of the baseline conditions for each compressor. The results of each plot show a decrease in the rates of compressor degradation and SFC increase for the coated compressor compared to the non-coated compressor. Overall test results show that it is feasible to utilize anti-fouling compressor coatings to reduce the rate of specific fuel consumption increase associated with compressor performance degradation.

scholarly journals High-Temperature Turbine Technology Readiness

1982 ◽  
Author(s):  
M. W. Horner ◽  
A. Caruvana
Keyword(s):  
High Temperature ◽  
Gas Turbine ◽  
Phase Ii ◽  
Combined Cycle ◽  
Technology Readiness ◽  
Inlet Temperature ◽  
Test Results ◽  
Turbine Inlet ◽  
Combined Cycle Plant ◽  
Gas Fuel

Final component and technology verification tests have been completed for application to a 2600°F rotor inlet temperature gas turbine. These tests have proven the capability of combustor, turbine hot section, and IGCC fuel systems and controls to operate in a combined cycle plant burning a coal-derived gas fuel at elevated gas turbine inlet temperatures (2600–3000°F). This paper presents recent test results and summarizes the overall progress made during the DOE-HTTT Phase II program.

scholarly journals Cooling and Sealing Air System in Industrial Gas Turbine Engines

1996 ◽  
Author(s):  
A. W. Reichert ◽  
M. Janssen
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Gas Turbines ◽  
State Of The Art ◽  
Cooling System ◽  
Inlet Temperature ◽  
Turbine Inlet ◽  
Air System ◽  
Calculation System ◽  
Cooling Air

Siemens heavy duty Gas Turbines have been well known for their high power output combined with high efficiency and reliability for more than 3 decades. Offering state of the art technology at all times, the requirements concerning the cooling and sealing air system have increased with technological development over the years. In particular the increase of the turbine inlet temperature and reduced NOx requirements demand a highly efficient cooling and sealing air system. The new Vx4.3A family of Siemens gas turbines with ISO turbine inlet temperatures of 1190°C in the power range of 70 to 240 MW uses an effective film cooling technique for the turbine stages 1 and 2 to ensure the minimum cooling air requirement possible. In addition, the application of film cooling enables the cooling system to be simplified. For example, in the new gas turbine family no intercooler and no cooling air booster for the first turbine vane are needed. This paper deals with the internal air system of Siemens gas turbines which supplies cooling and sealing air. A general overview is given and some problems and their technical solutions are discussed. Furthermore a state of the art calculation system for the prediction of the thermodynamic states of the cooling and sealing air is introduced. The calculation system is based on the flow calculation package Flowmaster (Flowmaster International Ltd.), which has been modified for the requirements of the internal air system. The comparison of computational results with measurements give a good impression of the high accuracy of the calculation method used.

Expanding Fuel Flexibility in MHPS’ Dry Low NOx Combustor

2018 ◽  
Author(s):  
Katsuyoshi Tada ◽  
Kei Inoue ◽  
Tomo Kawakami ◽  
Keijiro Saitoh ◽  
Satoshi Tanimura
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Environmental Conservation ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Social Perspectives ◽  
Turbine Inlet ◽  
Fuel Flexibility

Gas-turbine combined-cycle (GTCC) power generation is clean and efficient, and its demand will increase in the future from economic and social perspectives. Raising turbine inlet temperature is an effective way to increase combined cycle efficiency and contributes to global environmental conservation by reducing CO2 emissions and preventing global warming. However, increasing turbine inlet temperature can lead to the increase of NOx emissions, depletion of the ozone layer and generation of photochemical smog. To deal with this issue, MHPS (MITSUBISHI HITACHI POWER SYSTEMS) and MHI (MITSUBISHI HEAVY INDUSTRIES) have developed Dry Low NOx (DLN) combustion techniques for high temperature gas turbines. In addition, fuel flexibility is one of the most important features for DLN combustors to meet the requirement of the gas turbine market. MHPS and MHI have demonstrated DLN combustor fuel flexibility with natural gas (NG) fuels that have a large Wobbe Index variation, a Hydrogen-NG mixture, and crude oils.

Off-design performance improvement of twin-shaft gas turbine by variable geometry turbine and compressor besides fuel control

2019 ◽  
Vol 234 (7) ◽  
pp. 957-980
Author(s):  
Sepehr Sanaye ◽  
Salahadin Hosseini
Keyword(s):  
Life Cycle ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Guide Vane ◽  
Design Parameters ◽  
Inlet Guide Vane ◽  
Inlet Temperature ◽  
Gas Generator ◽  
Turbine Inlet ◽  
Exit Temperature

A novel procedure for finding the optimum values of design parameters of industrial twin-shaft gas turbines at various ambient temperatures is presented here. This paper focuses on being off design due to various ambient temperatures. The gas turbine modeling is performed by applying compressor and turbine characteristic maps and using thermodynamic matching method. The gas turbine power output is selected as an objective function in optimization procedure with genetic algorithm. Design parameters are compressor inlet guide vane angle, turbine exit temperature, and power turbine inlet nozzle guide vane angle. The novel constrains in optimization are compressor surge margin and turbine blade life cycle. A trained neural network is used for life cycle estimation of high pressure (gas generator) turbine blades. Results for optimum values for nozzle guide vane/inlet guide vane (23°/27°–27°/6°) in ambient temperature range of 25–45 ℃ provided higher net power output (3–4.3%) and more secured compressor surge margin in comparison with that for gas turbines control by turbine exit temperature. Gas turbines thermal efficiency also increased from 0.09 to 0.34% (while the gas generator turbine first rotor blade creep life cycle was kept almost constant about 40,000 h). Meanwhile, the averaged values for turbine exit temperature/turbine inlet temperature changed from 831.2/1475 to 823/1471°K, respectively, which shows about 1% decrease in turbine exit temperature and 0.3% decrease in turbine inlet temperature.

Analyses and Optimization of a Propulsion Cycle for Unmixed High Bypass Turbofan

2008 ◽  
Author(s):  
Adel Ghenaiet
Keyword(s):  
Fuel Consumption ◽  
Pressure Ratio ◽  
Specific Fuel Consumption ◽  
Design Parameters ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
High Pressure Ratio ◽  
Turbine Inlet ◽  
Design Variables ◽  
Bypass Ratio

This paper deals with a parametric study and an optimization for the design variables of a high bypass unmixed turbofan equipping commercial aircrafts. The objective of the first part of this study is to highlight the effects of the principal design parameters (bypass ratio, compression ratios, turbine inlet temperature etc..) on the uninstalled performance, in terms of specific thrust and specific fuel consumption. The second part concerns the optimization, aiming at finding the optimum design parameters concurrently minimizing the specific fuel consumption at cruise, and meeting the thrust requirement at takeoff. The cycle analyzer (on-design and off-design) as coupled to the optimization algorithm MMFD by adopting a random multi-starts search strategy is shown to be stable and converging. The predefined requirements and constraints have dictated utilizing an engine with a high-bypass ratio, high-pressure ratio and a moderate turbine inlet temperature. In general, the obtained results compare fairly well with typical data available for an equivalent ‘reference’ engine. This elaborated methodology is shown to be consistent with the conceptual design requirements and accuracy, because, it does not use components’ characteristics, and operates on simplifying assumptions. This present methodology can be readily adapted for other configurations of aero-engines as well, and easily integrated in a multi-disciplinary design approach.

Recent Advances of Internal Cooling Techniques for Gas Turbine Airfoils

2013 ◽  
Vol 5 (2) ◽  
Author(s):  
Minking K. Chyu ◽  
Sin Chien Siw
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Energy Demand ◽  
Major Elements ◽  
Inlet Temperature ◽  
Internal Cooling ◽  
Performance Goal ◽  
Turbine Inlet Temperature ◽  
Air Breathing ◽  
Turbine Inlet

The performance goal of modern gas turbine engines, both land-base and air-breathing engines, can be achieved by increasing the turbine inlet temperature (TIT). The level of TIT in the near future can reach as high as 1700 °C for utility turbines and over 1900 °C for advanced military engines. Advanced and innovative cooling techniques become one of the crucial major elements supporting the development of modern gas turbines, both land-based and air-breathing engines with continual increment of turbine inlet temperature (TIT) in order to meet higher energy demand and efficiency. This paper discusses state-of-the-art airfoil cooling techniques that are mainly applicable in the mainbody and trailing edge section of turbine airfoil. Potential internal cooling designs for near-term applications based on current manufacturing capabilities are identified. A literature survey focusing primarily on the past four to five years has also been performed.

Intercooled/Recuperated Shipboard Generator Drive Engine

1986 ◽  
Author(s):  
R. G. Mills ◽  
K. W. Karstensen
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
Gas Turbines ◽  
Electrical Power ◽  
Specific Fuel Consumption ◽  
Fire Control ◽  
Load Range ◽  
Light Load ◽  
Power Turbine ◽  
Variable Power

Adverse consequences of losing electrical power to complex electronic and fire control equipment, or of the sudden variations of shore power, cause naval combatants to operate two generators most of the time, each at light load where specific fuel consumption of simple-cycle gas turbines is particularly high. The recuperated gas turbine with variable power-turbine nozzles has a much better specific fuel consumption, especially at part load. Herein described is a compact recuperated gas turbine with variable power-turbine nozzles designed for marine and industrial use, suitable with or without intercooling. These features yield a specific fuel consumption that is comparable to marine diesels used for generator drive, and essentially flat across the entire usable load range.

Status of the Automotive Ceramic Gas Turbine Development Progrem: Year Four Progress

1995 ◽  
Author(s):  
Tsubura Nishiyama ◽  
Masumi Iwai ◽  
Norio Nakazawa ◽  
Masafumi Sasaki ◽  
Haruo Katagiri ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Inlet Temperature ◽  
Rotor Speed ◽  
Turbine Inlet Temperature ◽  
Turbine Engine ◽  
Turbine Inlet ◽  
Basic Engine ◽  
Energy Center ◽  
Engine Components

The seven-year program, designated “Research & Development of Automotive Ceramic Gas Turbine Engine (CGT Program)”, was started in 1990 with the object of demonstrating the advantageous potentials of ceramic gas turbines for automotive use. This CGT Program is conducted by Petroleum Energy Center. The basic engine is a 100kW, single-shaft regenerative engine having turbine inlet temperature of 1350°C and rotor speed of 110000rpm. In the forth year of the program, the engine components were experimentally evaluated and improved in the various test rigs, and the first assembly test including rotating and stationary components, was performed this year under the condition of turbine inlet temperature of 1200°C.

scholarly journals Exergy Efficiency Optimization for Gas Turbine Based Cogeneration Systems

2013 ◽  
Author(s):  
Ana C. Ferreira ◽  
Senhorinha F. Teixeira ◽  
José C. Teixeira ◽  
Manuel L. Nunes ◽  
Luís B. Martins
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Exergy Analysis ◽  
Exergy Efficiency ◽  
Plant Performance ◽  
System Component ◽  
Inlet Temperature ◽  
Exergy Destruction ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet

Energy degradation can be calculated by the quantification of entropy and loss of work and is a common approach in power plant performance analysis. Information about the location, amount and sources of system deficiencies are determined by the exergy analysis, which quantifies the exergy destruction. Micro-gas turbines are prime movers that are ideally suited for cogeneration applications due to their flexibility in providing stable and reliable power. This paper presents an exergy analysis by means of a numerical simulation of a regenerative micro-gas turbine for cogeneration applications. The main objective is to study the best configuration of each system component, considering the minimization of the system irreversibilities. Each component of the system was evaluated considering the quantitative exergy balance. Subsequently the optimization procedure was applied to the mathematical model that describes the full system. The rate of irreversibility, efficiency and flaws are highlighted for each system component and for the whole system. The effect of turbine inlet temperature change on plant exergy destruction was also evaluated. The results disclose that considerable exergy destruction occurs in the combustion chamber. Also, it was revealed that the exergy efficiency is expressively dependent on the changes of the turbine inlet temperature and increases with the latter.

Sign in / Sign up

Export Citation Format

Share Document