Effects of Air Bearing Stiffness on a Hard Disk Drive Subject to Shock and Vibration

2003 ◽  
Vol 125 (2) ◽  
pp. 343-349 ◽  
Author(s):  
Eric M. Jayson ◽  
J. Murphy ◽  
P. W. Smith ◽  
Frank E. Talke
Keyword(s):  
Finite Element ◽  
Hard Disk Drive ◽  
Hard Disk ◽  
Disk Drive ◽  
Element Model ◽  
Air Bearing ◽  
Head Disk Interface ◽  
Disk Interface ◽  
Wide Range ◽  
Bearing Stiffness

A finite element model of a hard disk drive (HDD) is developed to investigate the transient response of an operational HDD subject to shock and vibration. The air bearing stiffness of the head disk interface is determined from a finite element solution of the Reynolds equation and approximated with linear springs. The structural response is analyzed for several types of sliders with a wide range of air bearing stiffness. Results show the response of the head-disk interface subject to shock and the modes excited by vertical and lateral vibrations of the HDD.

Optimization of Air Bearing Contours for Shock Performance of a Hard Disk Drive

2003 ◽  
Author(s):  
Eric M. Jayson ◽  
Frank E. Talke
Keyword(s):  
Hard Disk Drive ◽  
Hard Disk Drives ◽  
Hard Disk ◽  
Disk Drive ◽  
Element Model ◽  
Time Dependent ◽  
Air Bearing ◽  
Disk Interface ◽  
Shock Response ◽  
Shock Event

Hard disk drives must be designed to withstand shock during operation. Large movements of the slider during shock impulse can cause reading and writing errors, track misregistration, or in extreme cases, damage to the magnetic material and loss of data. The design of the air bearing contour determines the steady state flying conditions of the slider as well as dynamic flying conditions, including shock response. In this paper a finite element model of the hard disk drive mechanical components was developed to determine the time dependent forces and moments applied to the slider during a shock event. The time dependent forces and moments are applied as external loads in a solution of the dynamic Reynolds equation to determine the slider response to a shock event. The genetic algorithm was then used to optimize the air bearing contour for optimum shock response while keeping the steady flying conditions constant. The results show substantial differences in the spacing modulation of the head/disk interface after a shock as a function of the design of the air bearing contour.

Optimization of Air Bearing Contours for Shock Performance of a Hard Disk Drive

2005 ◽  
Vol 127 (4) ◽  
pp. 878-883 ◽  
Author(s):  
Eric M. Jayson ◽  
Frank E. Talke
Keyword(s):  
Hard Disk Drive ◽  
Hard Disk Drives ◽  
Hard Disk ◽  
Disk Drive ◽  
Element Model ◽  
Time Dependent ◽  
Air Bearing ◽  
Disk Interface ◽  
Shock Response ◽  
Shock Event

Hard disk drives must be designed to withstand shock during operation. Large movements of the slider during a shock impulse can cause reading and writing errors, track misregistration, or in extreme cases, damage to the magnetic material and loss of data. The design of the air bearing contour determines the steady-state flying conditions of the slider as well as dynamic flying conditions, including shock response. In this paper a finite element model of the hard disk drive mechanical components was developed to determine the time dependent forces and moments applied to the slider during a shock event. The time-dependent forces and moments are applied as external loads in a solution of the dynamic Reynolds equation to determine the slider response to a shock event. The genetic algorithm was then used to optimize the air bearing contour for optimum shock response while keeping the steady flying conditions constant. The results show substantial differences in the spacing modulation of the head-disk interface after a shock as a function of the design of the air bearing contour.

SHOCK RESPONSE OF THE CLAMPED DISK IN SMALL FORM FACTOR HARD DISK DRIVE

2008 ◽  
Vol 22 (09n11) ◽  
pp. 1592-1597 ◽  
Author(s):  
BIN GU ◽  
DONGWEI SHU ◽  
BAOJUN SHI ◽  
GUOXING LU
Keyword(s):  
Finite Element ◽  
Form Factor ◽  
Hard Disk Drive ◽  
Hard Disk Drives ◽  
Hard Disk ◽  
Disk Drive ◽  
Element Model ◽  
Small Form ◽  
Shock Response ◽  
Small Form Factor

As small form factor (one-inch and smaller) hard disk drives are widely used in portable consumer appliances and gadgets, their mechanical robustness is of greater concern. In the previous work, it is found that when the disk is more tightly clamped, it helps to decrease the shock response of the disk and then avoid the head slap. In this paper, the real boundary condition of the disk for a small form factor hard disk drive from Seagate is investigated numerically. The disk is clamped between the clamp and the hub. The shock response of the disk under a half-sine acceleration pulse is simulated by using the finite element method. In the finite element model, both contact between disk and clamp and contact between disk and hub are considered. According to the simulation results, how to decrease the shock response of the disk is suggested.

Wear Analysis of Head-Disk Interface During Contact

2005 ◽  
Vol 127 (1) ◽  
pp. 171-179 ◽  
Author(s):  
Wei Peng ◽  
James Kiely ◽  
Yiao-Tee Hsia
Keyword(s):  
Hard Disk Drive ◽  
Wear Mechanism ◽  
Adhesive Wear ◽  
Contact Stiffness ◽  
Hard Disk ◽  
Disk Drive ◽  
Head Disk Interface ◽  
Wear Coefficient ◽  
Disk Interface ◽  
Fly Height

To achieve a higher storage density in a hard disk drive, the fly height of the air bearing slider, as part of the magnetic spacing, has to be minimized. At an ultralow fly height, the intermittent–continuous contact at the head–disk interface (HDI) is unavoidable and directly affects the mechanical and magnetic performance of the hard disk drive, and is of great interest. The HDI wear has a nonlinear and time-varying nature due to the change of contact force and roughness. To predict the HDI wear evolution, an iterative model of Coupled Head And Disk (CHAD) wear, is developed based on the contact mechanics. In this model, a composite transient wear coefficient is adopted and multiple phases of the wear evolution are established. A comprehensive contact stiffness is derived to characterize the contact at the HDI. The abrasive and adhesive wear is calculated based on the extended Archard’s wear law. The plastic and elastic contact areas are calculated with a three-dimensional (3D) sliding contact model. Based on the CHAD wear model, for the first time, the coupling between head and disk wear evolutions is thoroughly investigated. Accelerated wear tests have also been performed to verify the disk wear effect on the slider wear. A wear coefficient drop with time is observed during the tests and it is attributed to a wear mechanism shift from abrasive to adhesive wear. A shift in the type of contact from plastic to elastic accounts for the wear mechanism change.

Effect of Non-Operational Shock on Interaction Between Suspension Lift-Tab and Load/Unload Ramp

2005 ◽  
Author(s):  
Aravind N. Murthy ◽  
Eric M. Jayson ◽  
Frank E. Talke
Keyword(s):  
Hard Disk Drive ◽  
Failure Modes ◽  
Hard Disk Drives ◽  
Hard Disk ◽  
Areal Density ◽  
Disk Drive ◽  
Disk Drives ◽  
Head Disk Interface ◽  
Disk Interface ◽  
Operational Shock

Most hard disk drives manufactured in the last few years have Load/Unload (L/UL) technology. As opposed to the Contact Start/Stop (CSS) technology, L/UL technology has the advantage of improved areal density because of more disk space availability and better shock performance. The latter characteristic has significant benefits during the non-operational state of the hard disk drive since head/disk interactions are eliminated and the head is parked on a ramp adjacent to the disk. However, even if head/disk interactions are absent, other failure modes may occur such as lift-tab damage and dimple separation leading to flexure damage. A number of investigations have been made to study the response of the head disk interface with respect to shock when the head is parked on the disk ([1], [2]). In this paper, we address the effect of non-operational shock for L/UL disk drives.

Sign in / Sign up

Export Citation Format

Share Document