Physical Modeling of Pull-in Loads for Subsea Jumper Installation

2002 ◽  
Vol 124 (3) ◽  
pp. 113-119
Author(s):  
J. S. Damgaard ◽  
J. White ◽  
M. Worsley
Keyword(s):  
Physical Model ◽  
Physical Modeling ◽  
Model Testing ◽  
Model Tests ◽  
Physical Model Tests ◽  
Different Types ◽  
Relevant Field

Physical model tests have been performed with the aim of investigating the pull-in loads required to move a jumper assembly across the seabed. A total of 41 tests were completed with various assembly configurations, using two different types of sediment: sand and clay. It is shown that physical model testing is a viable procedure for studying prototype pull-in loads for relevant field situations.

Testing the Effectiveness of Scour Countermeasures by Physical Modeling

2000 ◽  
Vol 1696 (1) ◽  
pp. 251-257
Author(s):  
Norbert O. Eisenhauer ◽  
Bernd Rossbach
Keyword(s):  
Physical Model ◽  
Physical Modeling ◽  
Ad Hoc ◽  
Model Tests ◽  
Rhine River ◽  
Flood Events ◽  
Mean Flow ◽  
Negative Effects ◽  
Physical Model Tests ◽  
The Stability

The physical modeling of the scouring process at bridge piers is a proven method to obtain information about the size of the scour and the flow velocities that generate the scour. On the basis of this information, appropriate countermeasures can be designed. The advantage of the physical model is its application to all, even the most complex, pier geometries. Because approach flow is uniform in most cases, physical model tests can be carried out in a hydraulic flume, a method that gives fast and reliable results. The Federal Waterways and Engineering Institute (Bundesanstalt für Wasserbau) in Karlsruhe, Germany, conducted such model tests using piers of a new bridge over the Rhine River between the cities of Mannheim and Ludwigshafen. Shortly after sheet piles were driven into the riverbed as a formwork for the lower part of the pier, severe scouring of the riverbed occurred. Consequently, the stability of the sheet pile formwork was endangered. The ad hoc countermeasure of placing riprap into the scour did not stop local scouring. An additional cover layer of coarser stones was placed on top of the previous layer, stopping the erosion process at mean flow. Model tests were conducted to estimate the durability and stability of the ad hoc countermeasure for flood events. The tests proved that the riprap was stable, even at flood events, and that the scour had shifted away from the pier to the joint between the riprap and the original riverbed. A flood event with a peak of 3 days above the tested flood water level occurred in March 1999. No negative effects on the riprap have been observed until now.

scholarly journals PORT RESONANCE MITIGATION MODELED INTRODUCING ARJ-R STRUCTURES

2020 ◽  
pp. 38
Author(s):  
Jose A. GONZALEZ-ESCRIVA ◽  
Josep R. MEDINA ◽  
Joaquin M. GARRIDO
Keyword(s):  
Reflection Coefficient ◽  
Physical Model ◽  
Large Scale ◽  
Low Frequency ◽  
Model Tests ◽  
Wave Interference ◽  
Low Frequency Oscillations ◽  
Physical Model Tests ◽  
Similar Cost ◽  
Interference Mechanism

ARJ-R caissons are based on the "long-circuit" concept (Medina et al, 2016) that allows the extension of the destructive wave interference mechanism to mitigate low frequency oscillations without enlarging the width of the caisson. The performance of the ARJ-R caissons is referred to its reflection coefficient (Cr) which was obtained through large-scale physical model tests (Gonzalez-Escriva et al, 2018). In this paper, the effectiveness of Anti-Reflective Jarlan-type structures for Port Resonance mitigation (ARJ-R) has been assessed numerically for the port of Denia (Spain). ARJ-R structures are constructible, with similar dimensions as conventional vertical quay caissons and with a similar cost (15percent more than conventional vertical caisson).Recorded Presentation from the vICCE (YouTube Link): https://youtu.be/LomQEVpvjik

scholarly journals OPTIMIZATION OF THE WAVECAT WAVE ENERGY CONVERTER

2012 ◽  
Vol 1 (33) ◽  
pp. 5 ◽  
Author(s):  
Hernan Fernandez ◽  
Gregorio Iglesias ◽  
Rodrigo Carballo ◽  
Alberte Castro ◽  
Marcos Sánchez ◽  
...  
Keyword(s):  
Physical Model ◽  
Wave Energy ◽  
Model Tests ◽  
Irregular Waves ◽  
Intermediate Water ◽  
Plan View ◽  
Santiago De Compostela ◽  
Wave Energy Converters ◽  
Physical Model Tests ◽  
The Difference

The development of efficient, reliable Wave Energy Converters (WECs) is a prerequisite for wave energy to become a commercially viable energy source. Intensive research is currently under way on a number of WECs, among which WaveCat©—a new WEC recently patented by the University of Santiago de Compostela. In this sense, this paper describes the WaveCat concept and its ongoing development and optimization. WaveCat is a floating WEC intended for operation in intermediate water depths (50–100 m). Like a catamaran, it consists of two hulls—from which it derives its name. The difference with a conventional catamaran is that the hulls are not parallel but convergent; they are joined at the stern, forming a wedge in plan view. Physical model tests of a 1:30 model were conducted in a wave tank using both regular and irregular waves. In addition to the waves and overtopping rates, the model displacements were monitored using a non-intrusive system. The results of the physical model tests will be used to validate the 3D numerical model, which in turn will be used to optimize the design of WaveCat for best performance under a given set of wave conditions.

scholarly journals LARGE AND SMALL SCALE WAVE OVERTOPPING MEASUREMENTS FOR AFSLUITDIJK REHABILITATION PROJECT

2020 ◽  
pp. 15
Author(s):  
Wouter Ockeloen ◽  
Coen Kuiper ◽  
Sjoerd van den Steen
Keyword(s):  
Water Management ◽  
Physical Model ◽  
Large Scale ◽  
Wadden Sea ◽  
Model Tests ◽  
Small Scale ◽  
Water Safety ◽  
Wave Overtopping ◽  
Physical Model Tests ◽  
Large Scale Tests

The 'Afsluitdijk' is a 32 km enclosure dam which separates the Wadden sea and the Lake IJssel. The dam currently undergoes a major rehabilitation to meet the requirements with regard to water safety. The Dutch Ministry of infrastructure and Water Management (Rijkswaterstaat division) has commissioned Levvel, a consortium of BAM, Van Oord and Rebel, to prepare the design and carry out the reconstruction of the dam including sluices and highway. The project includes reinforcement of the armour layers and wave overtopping reduction. As part of the contract Rijkswaterstaat prescribed the contractor (Levvel) to verify the design with large scale physical model tests (min. 1:3 scale). These tests were carried out in the Delta Flume of Deltares. Prior to the large scale tests, smaller scale tests (1:20) have been carried out to optimize the design with regard to armour stability and wave overtopping. The research described here focuses on the wave overtopping.Recorded Presentation from the vICCE (YouTube Link): https://youtu.be/kPga0wVCCIE

scholarly journals Study on the Water-Physical Properties of the Cement-Plaster Bonded Rock-Like Materials

2021 ◽  
Vol 2021 ◽  
pp. 1-7
Author(s):  
Yong Zhang ◽  
Zhiguo Cao ◽  
Xiaomeng Shi
Keyword(s):  
Physical Properties ◽  
Physical Model ◽  
Coupling Model ◽  
Model Tests ◽  
Physical Parameters ◽  
Test Results ◽  
Physical Model Tests ◽  
Fluid Coupling ◽  
Softening Coefficient ◽  
Solid Fluid Coupling

The cement-plaster bonded rock-like material is one of the most commonly used materials to simulate different rocks in physical model tests. However, the applicability of this material in solid-fluid coupling model tests is not clear because there are few research studies on the water-physical properties of this material and its similarity to the actual rock is uncertain. This paper presents a systemic experimental study on the water-physical properties of the cement-plaster bonded rock-like materials. The parameters of rock-like materials, including water absorption, softening coefficient, and permeability coefficient, were compared with those of actual rocks to analyse the applicability of such material. Then, the influence of proportion on the water-physical properties of this material was discussed. By multiple regression analysis of the test results, empirical equations between the water-physical parameters and proportions were proposed. The equations can be used to estimate the water-physical properties of cement-plaster bonded rock-like materials with specific proportion and thus to select suitable materials in the solid-fluid coupling physical model tests.

scholarly journals PHYSICAL MODEL TESTS ON WAVE OVERTOPPING AND FLOW PROCESSES ON DIKE CRESTS INFLUENCED BY WAVE-CURRENT INTERACTION

2012 ◽  
Vol 1 (33) ◽  
pp. 34 ◽  
Author(s):  
Stefanie Lorke ◽  
Babette Scheres ◽  
Holger Schüttrumpf ◽  
Antje Bornschein ◽  
Reinhard Pohl
Keyword(s):  
Physical Model ◽  
Model Tests ◽  
Longshore Current ◽  
Wind Fields ◽  
Incoming Wave ◽  
Wave Overtopping ◽  
Improve Design ◽  
Physical Model Tests ◽  
Flow Processes ◽  
Run Up

Flow processes like flow depths and flow velocities give important information about erosion and infiltration processes, which can lead to an unstable dike structure and consequently to dike failure. Up to now several physical model tests on wave run-up and wave overtopping are available to adjust and improve design formula for different dike structures. This kind of physical model tests have been performed in the here presented project FlowDike. Its main purpose is to consider two new aspects that could influence the assessment of wave run-up and wave overtopping as well as the flow processes on dikes which have not been investigated yet: longshore current and wind. Especially in estuaries and along coasts, the effect of tidal and storm induced currents combined with local wind fields can influence the incoming wave parameters at the dike toe as well as the wave run-up height, the wave overtopping rate and the flow processes on dikes. This paper will focus on these flow processes on dike slopes and dike crests on an 1:6 sloped dike influenced by oblique wave attack and longshore current.

Sign in / Sign up

Export Citation Format

Share Document