Application of Boundary Layer Fences and Vortex Generators in Improving Performance of S-Duct Diffusers

2001 ◽  
Vol 124 (1) ◽  
pp. 136-142 ◽  
Author(s):  
R. K. Sullerey ◽  
Sourabh Mishra ◽  
A. M. Pradeep
Keyword(s):  
Boundary Layer ◽  
Total Pressure ◽  
Static Pressure ◽  
Transverse Velocity ◽  
Pressure Rise ◽  
Vortex Generator ◽  
Substantial Improvement ◽  
Vortex Generators ◽  
Flow Distortion ◽  
Flow Quality

An experimental investigation was undertaken to study the effect of various fences and vortex generator configurations in reducing the exit flow distortion and improving total pressure recovery in two-dimensional S-duct diffusers of different radius ratios. Detailed measurements including total pressure and velocity distribution, surface static pressure, skin friction, and boundary layer measurements were taken in a uniform inlet flow at a Reynolds number of 7.8×105. These measurements are presented here along with static pressure rise, distortion coefficient, and the transverse velocity vectors at the duct exit determined from the measured data. The results indicate that substantial improvement in static pressure rise and flow quality is possible with judicious deployment of fences and vortex generators.

Secondary Flows and Separation in S-Duct Diffusers: Their Detection and Control

2003 ◽  
Author(s):  
R. K. Sullerey ◽  
A. M. Pradeep
Keyword(s):  
Total Pressure ◽  
Static Pressure ◽  
Transverse Velocity ◽  
Pressure Rise ◽  
Vortex Generator ◽  
Substantial Improvement ◽  
Secondary Flows ◽  
Flow Quality ◽  
Vortex Generator Jets ◽  
And Control

An experimental investigation was undertaken to detect and control secondary flows and separation in two-dimensional Sduct diffusers. Active control by vortex generator jets was applied to control secondary flows. The experiments were carried out with and without inflow distortion. Detailed measurements including total pressure and velocity distribution, surface static pressure, skin friction and boundary layer measurements were taken at an inlet Reynolds number of 7.8 × 105. These measurements are presented here along with static pressure rise, distortion coefficient, total pressure loss coefficients and the transverse velocity vectors at the duct exit determined from the measured data. Substantial improvement in static pressure rise and flow quality was achieved by the use of vortex generator jets.

Effect of a New Vortex Generator on the Performance of an Axial Compressor Cascade at Design and Off-Design Conditions

2015 ◽  
Author(s):  
Ahmed M. Diaa ◽  
Mohammed F. El-Dosoky ◽  
Mahmoud A. Ahmed ◽  
Omar E. Abdelhafez
Keyword(s):  
Total Pressure ◽  
Static Pressure ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Vortex Generator ◽  
Secondary Flows ◽  
Vortex Generators ◽  
Compressor Cascade ◽  
Diffusion Factor ◽  
Compressor Performance

Secondary flows are noxious to axial compressor performance. To overcome and control those secondary flows, vortex generators are used as a passive control device. Controlling secondary flows will lead to a further improvements in the compressor performance. A new design of vortex generator is considered in this investigation in order to control secondary flows in axial compressor cascade at design and off-design conditions. Numerical simulations of a three-dimensional compressible turbulent flow have been performed to explore the effect of the vortex generators on the reduction of secondary flows. Six different incidence angles are used for the off-design operation investigations. Based on the simulation results, the pressure, velocity, and streamline are used to follow up the development of the secondary flows. Thence, total pressure loss coefficient, static pressure rise coefficient, difference in flow deflection angle, and diffusion factor are estimated. Results indicate that vortex generators have a significant effect on the development of secondary flows at off design operation as they cause a reduction in total pressure loss, they also affect the loading behavior of the cascade as they cause a slight change in the cascade deflection, and a slight decrease in the diffusion factor which causes unloading of the blade. Static pressure rise is significantly reduced at negative incidence angles while a slight reduction occurs at positive incidence angles. In a word, the new design of the vortex generator enhances the cascade aerodynamic performance and enlarges the operating range of the cascade towards the positive incidence region.

Sub boundary-layer vortex generators for the control of shock induced separation

2006 ◽  
Vol 110 (1106) ◽  
pp. 215-226 ◽  
Author(s):  
G. S. Cohen ◽  
F. Motallebi
Keyword(s):  
Boundary Layer ◽  
Total Pressure ◽  
Static Pressure ◽  
Pressure Rise ◽  
Boundary Layer Separation ◽  
Vortex Generators ◽  
Pressure Recovery ◽  
Flow Visualisation ◽  
Pressure Distributions ◽  
Pressure Profiles

Abstract The results of an investigation into the effects that sub-boundary layer vortex generators (SBVGs) have on reducing normal shock-induced turbulent boundary-layer separation are presented. The freestream Mach number and Reynolds number were M = 1·45 and 15·9 × 106/m, respectively. Total pressure profiles, static pressure distributions, surface total pressure distributions, oil flow visualisation and Schlieren photographs were used in the results analysis. The effects of SBVG height, lateral spacing and location upstream of the shock were investigated. A novel curved shape SBVG was also evaluated and comparisons against the conventional flat vane type were made. The results show that in all but two cases, separation was completely eliminated. As expected, the largest SBVGs with height, h = 55%δ, provided the greatest pressure recovery and maximum mixing. However, the shock pressure rise was highest for this case. The experiments showed that the mid height SBVG array with the largest spacing provided similar results to the SBVG array with the largest height. Reducing the distance to shock to 10δ upstream also showed some improvement over the SBVG position of 18δ upstream. It was suggested that total elimination of the separated region may not be required to achieve a balance of improved static pressure recovery whilst minimising the pressure rise through the shock. The effect of curving the SBVGs provided an improved near wall mixing with an improved static and surface total pressure recovery downstream of the separation line. The optimum SBVG for the current flow conditions was found to be the curved vanes of h = 40%δ, with the largest spacing, located at 18δ upstream of the shock. Overall, it was apparent from the results that in comparison to larger vortex generators with a height comparable to δ, for SBVGs the parameters involved become more important in order to obtain the highest degree of mixing from a given SBVG configuration.

Influence of the height of the vortex generators in the control of shock-induced separation of the boundary layers

2008 ◽  
Vol 112 (1133) ◽  
pp. 415-420
Author(s):  
G. S. Cohen ◽  
F. Motallebi
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Total Pressure ◽  
Static Pressure ◽  
Pressure Rise ◽  
Boundary Layer Separation ◽  
Vortex Generators ◽  
Flow Visualisation ◽  
Near Surface ◽  
Pressure Distributions

Abstract Experiments have been conducted to assess the effects that sub-boundary-layer vortex generators (SBVGs) have on reducing normal shock-induced turbulent boundary-layer separation. The freestream Mach number and Reynolds number were M = 1·45 and 15·9 × 106/m, respectively. Detailed measurements of a fully developed, flat plate turbulent boundary layer were used in order to assess the performance of ten different SBVG configurations. The SBVG performance was assessed by comparing total pressure profiles measured upstream of separation and downstream of reattachment. Static pressure distributions, near surface total pressure distributions, oil flow visualisation and Schlieren photographs were also used. The effect of SBVG height was investigated. The results show the largest SBVGs with height, h = 55%δ, provided the greatest static pressure recovery and maximum mixing. However, the shock pressure rise (wave drag) was highest for this case.

Secondary Flow Control Using Vortex Generator Jets

2004 ◽  
Vol 126 (4) ◽  
pp. 650-657 ◽  
Author(s):  
R. K. Sullerey ◽  
A. M. Pradeep
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Vortex Generator ◽  
Control Flow ◽  
Secondary Flows ◽  
Total Pressure Loss ◽  
Vortex Generators ◽  
Vortex Generator Jets ◽  
Inflow Conditions

In this paper, results are presented of an experimental investigation into the effectiveness of vortex generator jets in controlling secondary flows in two-dimensional S-duct diffusers. The experiments were performed in uniform and distorted inflow conditions and the performance evaluation of the diffuser was carried out in terms of static pressure recovery and quality of the exit flow. In the case with inflow distortion, tapered fin vortex generators were employed in addition to vortex generator jets to control flow separation that was detected on the wall with inflow distortion. Detailed measurements including total pressure, velocity distribution, surface static pressure, skin friction, and boundary layer measurements were taken at a Reynolds number of 7.8×105. These results are presented in terms of static pressure rise, distortion coefficient, and total pressure loss coefficient at the duct exit. For uniform inflow, the use of vortex generator jets resulted in more than a 30 percent decrease in total pressure loss and flow distortion coefficients. In combination with passive device (tapered fin vortex generators), the vortex generator jets reduce total pressure losses by about 25 percent for distorted inflow conditions. A potential application of this method may include control of secondary flows in turbo machinery.

scholarly journals Characterization of Aerodynamic Performance of Boundary-Layer-Ingesting Inlet Under Crosswind

2012 ◽  
Author(s):  
Meng-Sing Liou ◽  
Byung Joon Lee
Keyword(s):  
Boundary Layer ◽  
Total Pressure ◽  
Flow Characteristics ◽  
Vortex Generator ◽  
Propulsion System ◽  
Flow Distortion ◽  
Inlet System ◽  
Fuel Savings ◽  
Design Changes ◽  
And Performance

NASA has been studying future transport concepts, envisioned to be technically realizable in the timeframe of 2020–2030, to meet environmental and performance goals. One concept receiving considerable interest involves a propulsion system embedded into a hybrid wingbody aircraft. While offering significant advantages in fuel savings and noise reduction by this concept, there are several technical challenges that are not encountered in the current fleet and must be overcome so as to deliver target performance and operability. One of these challenges is associated with an inlet system that ingests a significantly thick boundary layer, developing along the wingbody surface, into a serpentine diffuser before the flow meeting fan blades. The flow is subject to considerable total pressure loss and distorted at the fan face, much more significantly than in the inlet system of conventional aircraft. In our previous studies [1, 2], we have shown that through innovative design changes on the airframe surface, it is possible to simultaneously increase total pressure recovery and decrease distortion in the flow, without resorting to conventional penalty-ridden flow control concepts, such as vortex generator or boundary layer bleeding/suction. In the current study, we are interested in understanding the following issues: how the embedded propulsion system performs under a crosswind condition by studying in detail the flow characteristics of two inlets, the baseline and another optimized previously under the cruise condition. With the insight, it is hoped that it can help in the follow-on study by devising effective strategies to minimize flow distortion arising from the integration of an embedded-engine system into an airframe to the level acceptable to the operation of engine fan.

Numerical investigations on the effect of volute casing treatment for performance augmentation in a centrifugal fan

2021 ◽  
pp. 095440622110341
Author(s):  
Manjunath L Nilugal ◽  
K Vasudeva Karanth ◽  
Madhwesh N
Keyword(s):  
Total Pressure ◽  
Static Pressure ◽  
Numerical Study ◽  
Pressure Coefficient ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Centrifugal Fan ◽  
Casing Treatment ◽  
Sliding Mesh ◽  
Optimum Configuration

This article presents the effect of volute chamfering on the performance of a forward swept centrifugal fan. The numerical analysis is performed to obtain the performance parameters such as static pressure rise coefficient and total pressure coefficient for various flow coefficients. The chamfer ratio for the volute is optimized parametrically by providing a chamfer on either side of the volute. The influence of the chamfer ratio on the three dimensional flow domain was investigated numerically. The simulation is carried out using Re-Normalisation Group (RNG) k-[Formula: see text] turbulence model. The transient simulation of the fan system is done using standard sliding mesh method available in Fluent. It is found from the analysis that, configuration with chamfer ratio of 4.4 is found be the optimum configuration in terms of better performance characteristics. On an average, this optimum configuration provides improvement of about 6.3% in static pressure rise coefficient when compared to the base model. This optimized chamfer configuration also gives a higher total pressure coefficient of about 3% validating the augmentation in static pressure rise coefficient with respect to the base model. Hence, this numerical study establishes the effectiveness of optimally providing volute chamfer on the overall performance improvement of forward bladed centrifugal fan.

Effects of Area Ratio and Mean Rise Angle on the Aerodynamics of Interturbine Ducts

2018 ◽  
Vol 140 (9) ◽  
Author(s):  
Yanfeng Zhang ◽  
Shuzhen Hu ◽  
Ali Mahallati ◽  
Xue-Feng Zhang ◽  
Edward Vlasic
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Static Pressure ◽  
Computational Study ◽  
Pressure Rise ◽  
Adverse Pressure Gradient ◽  
Boundary Layer Separation ◽  
Wake Flow ◽  
Height Ratio ◽  
Inlet Swirl

This work, a continuation of a series of investigations on the aerodynamics of aggressive interturbine ducts (ITD), is aimed at providing detailed understanding of the flow physics and loss mechanisms in four different ITD geometries. A systematic experimental and computational study was carried out by varying duct outlet-to-inlet area ratios (ARs) and mean rise angles while keeping the duct length-to-inlet height ratio, Reynolds number, and inlet swirl constant in all four geometries. The flow structures within the ITDs were found to be dominated by the boundary layer separation and counter-rotating vortices in both the casing and hub regions. The duct mean rise angle determined the severity of adverse pressure gradient in the casing's first bend, whereas the duct AR mainly governed the second bend's static pressure rise. The combination of upstream wake flow and the first bend's adverse pressure gradient caused the boundary layer to separate and intensify the strength of counter-rotating vortices. At high mean rise angle, the separation became stronger at the casing's first bend and moved farther upstream. At high ARs, a two-dimensional separation appeared on the casing and resulted in increased loss. Pressure loss penalties increased significantly with increasing duct mean rise angle and AR.

CFD Studies on the Performance of a Centrifugal Compressor With Single Wall Rotating Vaneless Diffusers at the Wall Extension Ratios of 1.1 and 1.15

2017 ◽  
Author(s):  
Srinivasa Rao Konakala ◽  
Mukka Govardhan
Keyword(s):  
Centrifugal Compressor ◽  
Total Pressure ◽  
Static Pressure ◽  
Substantial Improvement ◽  
Significant Loss ◽  
Vaneless Diffuser ◽  
Shear Forces ◽  
Overall Performance ◽  
Vaneless Diffusers ◽  
And Performance

Efficiency of the centrifugal compressor is affected by non-uniform flow at the exit of the impeller and the losses in the diffuser. This causes a significant loss of total pressure and drop in the performance of a centrifugal compressor. By rotating some portion of stationary vaneless diffuser walls with the speed of the impeller, the shear forces between the flow and diffuser walls are greatly reduced. Thereby improvement in the operating range and performance is achieved. This paper presents CFD studies on the effect of different single wall rotations i.e. hub rotation and shroud rotation of the vaneless diffusers on the overall performance at 10% and 15% extension of impeller walls. It is observed that the performance characteristics of compressors with all RVD models offer higher static pressure recovery and also higher rate of diffusion compared to the base compressor with SVD. It is clear that as extended radius increases from 10% to 15%, substantial improvement of efficiency and reduction of losses are observed for both type of models. Out of two single wall rotation models, SRVD model is able to better mix the jet-wake type of impeller exit flows and minimizes the losses therein and improve the performance of the centrifugal compressor.

scholarly journals Computational Modelling of Three Different Sub-Boundary Layer Vortex Generators on a Flat Plate

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3107 ◽  
Author(s):  
Ruben Gutierrez-Amo ◽  
Unai Fernandez-Gamiz ◽  
Iñigo Errasti ◽  
Ekaitz Zulueta
Keyword(s):  
Boundary Layer ◽  
Flat Plate ◽  
Flow Separation ◽  
Computational Modelling ◽  
Vortex Generator ◽  
Vortex Generators ◽  
Primary Vortex ◽  
Good Efficiency ◽  
Local Boundary ◽  
Passive Flow Control

Flow separation is the source of several problems in a wind turbine including load fluctuations, lift losses, and vibrations. Vortex generators (VGs) are passive flow control devices used to delay flow separation, but their implementation may produce overload drag at the blade section where they are placed. In the current work, a computational model of different geometries of vortex generators placed on a flat plate has been carried out throughout fully meshed computational simulations using Reynolds Averaged Navier-Stokes (RANS) equations performed at a Reynolds number of R e θ = 2600 based on local boundary layer (BL) momentum thickness θ = 2.4 mm. A flow characterization of the wake behind the vortex generator has been done with the aim of evaluating the performance of three vortex generator geometries, namely Rectangular VG, Triangular VG, and Symmetrical VG NACA0012. The location of the primary vortex has been evaluated by the vertical and lateral trajectories and it has been found that for all analyzed VG geometries the primary vortex is developed below the boundary layer thickness δ = 20 mm for a similar vorticity level ( w x m a x ). Two innovative parameters have been developed in the present work for evaluating the vortex size and the vortex strength: Half-Life Surface S 05 and Mean Positive Circulation Γ 05 + . As a result, an assessment of the VG performance has been carried out by all analyzed parameters and the symmetrical vortex generator NACA0012 has provided good efficiency in energy transfer compared with the Rectangular VG.

Sign in / Sign up

Export Citation Format

Share Document