Acoustic Resonances of an Industrial Gas Turbine Combustion System

2000 ◽  
Vol 123 (4) ◽  
pp. 766-773 ◽  
Author(s):  
S. Hubbard ◽  
A. P. Dowling
Keyword(s):  
Gas Turbine ◽  
Acoustic Waves ◽  
Low Frequency ◽  
Helmholtz Resonator ◽  
Nonlinear Effects ◽  
Operating Conditions ◽  
Resonant Frequencies ◽  
Bulk Mode ◽  
Acoustic Resonances ◽  
Industrial Gas Turbine

A theory is developed to describe low-frequency acoustic waves in the complicated diffuser/combustor geometry of a typical industrial gas turbine. This is applied to the RB211-DLE geometry to give predictions for the frequencies of the acoustic resonances at a range of operating conditions. The main resonant frequencies are to be found around 605 Hz (associated with the plenum) and around 461 Hz and 823 Hz (associated with the combustion chamber), as well as one at around 22 Hz (a bulk mode associated with the system as a whole). The stabilizing effects of a Helmholtz resonator, which models damping through nonlinear effects, are included, together with effects of coupled pressure waves in the fuel supply system.

Acoustic Resonances of an Industrial Gas Turbine Combustion System

2000 ◽  
Author(s):  
S. Hubbard ◽  
A. P. Dowling
Keyword(s):  
Combustion Chamber ◽  
Gas Turbine ◽  
Acoustic Waves ◽  
Low Frequency ◽  
Operating Conditions ◽  
Combustion System ◽  
Resonant Frequencies ◽  
Bulk Mode ◽  
Acoustic Resonances ◽  
Industrial Gas Turbine

A theory is developed to describe low frequency acoustic waves in the complicated diffuser/combustor geometry of a typical industrial gas turbine. This is applied to the RB211-DLE geometry to give predictions for the frequencies of the acoustic resonances at a range of operating conditions. The main resonant frequencies are to be found around 605 Hz (associated with the plenum) and around 461 Hz and 823 Hz (associated with the combustion chamber), as well as one at around 22 Hz (a bulk mode associated with the system as a whole).

Predicting Thermoacoustic Instability in an Industrial Gas Turbine Combustor: Combining a Low Order Network Model With Flame LES

2017 ◽  
Author(s):  
Y. Xia ◽  
A. S. Morgans ◽  
W. P. Jones ◽  
J. Rogerson ◽  
G. Bulat ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Acoustic Waves ◽  
Gas Turbine Combustor ◽  
Network Modelling ◽  
Weakly Nonlinear ◽  
Thermoacoustic Instability ◽  
Reduced Chemistry ◽  
Flame Describing Function ◽  
Industrial Gas Turbine ◽  
Low Order

The thermoacoustic modes of a full scale industrial gas turbine combustor have been predicted numerically. The predictive approach combines low order network modelling of the acoustic waves in a simplified geometry, with a weakly nonlinear flame describing function, obtained from incompressible large eddy simulations of the flame region under upstream forced velocity perturbations, incorporating reduced chemistry mechanisms. Two incompressible solvers, each employing different numbers of reduced chemistry mechanism steps, are used to simulate the turbulent reacting flowfield to predict the flame describing functions. The predictions differ slightly between reduced chemistry approximations, indicating the need for more involved chemistry. These are then incorporated into a low order thermoacoustic solver to predict thermoacoustic modes. For the combustor operating at two different pressures, most thermoacoustic modes are predicted to be stable, in agreement with the experiments. The predicted modal frequencies are in good agreement with the measurements, although some mismatches in the predicted modal growth rates and hence modal stabilities are observed. Overall, these findings lend confidence in this coupled approach for real industrial gas turbine combustors.

scholarly journals The Design and Evaluation of a 14 Stage, 16:1 Pressure Ratio Compressor for an Industrial Gas Turbine

1996 ◽  
Author(s):  
Mohammad R. Saadatmand
Keyword(s):  
Experimental Data ◽  
Gas Turbine ◽  
Rotor Blade ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Suction Surface ◽  
Design Intent ◽  
Flow Through ◽  
Industrial Gas Turbine

The aerodynamic design process leading to the production configuration of a 14 stage, 16:1 pressure ratio compressor for the Taurus 70 gas turbine is described. The performance of the compressor is measured and compared to the design intent. Overall compressor performance at the design condition was found to be close to design intent. Flow profiles measured by vane mounted instrumentation are presented and discussed. The flow through the first rotor blade has been modeled at different operating conditions using the Dawes (1987) three-dimensional viscous code and the results are compared to the experimental data. The CFD prediction agreed well with the experimental data across the blade span, including the pile up of the boundary layer on the corner of the hub and the suction surface. The rotor blade was also analyzed with different grid refinement and the results were compared with the test data.

Experimental Assessment of the Emissions Benefits of a Ceramic Gas Turbine Combustor

1996 ◽  
Author(s):  
K. O. Smith ◽  
A. Fahme
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Flow Distribution ◽  
Operating Conditions ◽  
Nox Emissions ◽  
Fuel Injector ◽  
Gas Turbine Combustor ◽  
Experimental Assessment ◽  
Industrial Gas Turbine ◽  
Combustor Liner

Three subscale, cylindrical combustors were rig tested on natural gas at typical industrial gas turbine operating conditions. The intent of the testing was to determine the effect of combustor liner cooling on NOx and CO emissions. In order of decreasing liner cooling, a metal louvre-cooled combustor, a metal effusion-cooled combustor, and a backside-cooled ceramic (CFCC) combustor were evaluated. The three combustors were tested using the same lean-premixed fuel injector. Testing showed that reduced liner cooling produced lower CO emissions as reaction quenching near the liner wall was reduced. A reduction in CO emissions allows a reoptimization of the combustor air flow distribution to yield lower NOx emissions.

Numerical and Experimental Evaluation of a Dual-Fuel Dry-Low-NOx Micromix Combustor for Industrial Gas Turbine Applications

2018 ◽  
Vol 11 (1) ◽  
Author(s):  
Harald H. W. Funke ◽  
Nils Beckmann ◽  
Jan Keinz ◽  
Sylvester Abanteriba
Keyword(s):  
Gas Turbine ◽  
Combustion Process ◽  
Experimental Studies ◽  
Research Process ◽  
Operating Conditions ◽  
Experimental Investigations ◽  
Dual Fuel ◽  
Pure Hydrogen ◽  
Ongoing Research ◽  
Industrial Gas Turbine

Abstract The dry-low-NOx (DLN) micromix combustion technology has been developed originally as a low emission alternative for industrial gas turbine combustors fueled with hydrogen. Currently, the ongoing research process targets flexible fuel operation with hydrogen and syngas fuel. The nonpremixed combustion process features jet-in-crossflow-mixing of fuel and oxidizer and combustion through multiple miniaturized flames. The miniaturization of the flames leads to a significant reduction of NOx emissions due to the very short residence time of reactants in the flame. The paper presents the results of a numerical and experimental combustor test campaign. It is conducted as part of an integration study for a dual-fuel (H2 and H2/CO 90/10 vol %) micromix (MMX) combustion chamber prototype for application under full scale, pressurized gas turbine conditions in the auxiliary power unit Honeywell Garrett GTCP 36-300. In the presented experimental studies, the integration-optimized dual-fuel MMX combustor geometry is tested at atmospheric pressure over a range of gas turbine operating conditions with hydrogen and syngas fuel. The experimental investigations are supported by numerical combustion and flow simulations. For validation, the results of experimental exhaust gas analyses are applied. Despite the significantly differing fuel characteristics between pure hydrogen and hydrogen-rich syngas, the evaluated dual-fuel MMX prototype shows a significant low NOx performance and high combustion efficiency. The combustor features an increased energy density that benefits manufacturing complexity and costs.

Numerical Investigations of NOx Emissions of a Partially Premixed Burner for Natural Gas Operations in Industrial Gas Turbine

2014 ◽  
Author(s):  
Alessandro Innocenti ◽  
Antonio Andreini ◽  
Andrea Giusti ◽  
Bruno Facchini ◽  
Matteo Cerutti ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Turbulent Combustion ◽  
Fuel Injection ◽  
Formation Rate ◽  
Operating Conditions ◽  
Combustion Model ◽  
Nox Emissions ◽  
Air Concentration ◽  
Partially Premixed ◽  
Industrial Gas Turbine

In the present paper a numerical analysis of a low NOx partially premixed burner for industrial gas turbine applications is presented. The first part of the work is focused on the study of the premixing process inside the burner. Standard RANS CFD approach was used: k–ε turbulence model was modified and calibrated in order to find a configuration able to fit available experimental profiles of fuel/air concentration at the exit of the burner. The resulting profiles at different test points have been used to perform reactive simulations of an experimental test rig, where exhaust NOx emissions were measured. An assessment of the turbulent combustion model was carried out with a critical investigation of the expected turbulent combustion regimes in the system and taking into account the partially premixed nature of the flame due to the presence of diffusion type pilot flames. A reliable numerical setup was discovered by comparing predicted and measured NOx emissions at different operating conditions and at different split ratio between main and pilot fuel. In the investigated range, the influence of the premixer in the NOx formation rate was found to be marginal if compared with the pilot flame one. The calibrated numerical setup was then employed to explore possible modifications to fuel injection criteria and fuel split, with the aim of minimizing exhaust NOx emissions. This preliminary numerical screening of alternative fuel injection strategies allowed to define a set of advanced configurations to be investigated in future experimental tests.

Casing Vibration and Gas Turbine Operating Conditions

1989 ◽  
Author(s):  
K. Mathioudakis ◽  
E. Loukis ◽  
K. D. Papailiou
Keyword(s):  
Gas Turbine ◽  
Transfer Functions ◽  
Parametric Identification ◽  
Fast Response ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Unsteady Pressure ◽  
Signal Features ◽  
Surface Vibrations ◽  
Industrial Gas Turbine

The results from an experimental investigation of the compressor casing vibration of an industrial Gas Turbine are presented. It is demonstrated that statistical properties of acceleration signals can be linked with engine operating conditions. The power content of such signals is dominated by contributions originating from the stages of the compressor, while the contribution of the shaft excitation is secondary. Using non-parametric identification methods, accelerometer outputs are correlated to unsteady pressure measurements taken by fast response transducers at the inner surface of the compressor casing. The transfer functions allow reconstruction of unsteady pressure signal features from the accelerometer readings. A possibility is thus provided, for “seeing” the unsteady pressure field of the rotor blades without actually penetrating through the casing, but by simply observing its external surface vibrations.

Performance and Numerical Flow Investigations of an Industrial Gas Turbine Intake System Under Different Operating Conditions

2006 ◽  
Author(s):  
Friederike C. Mund ◽  
Pericles Pilidis
Keyword(s):  
Gas Turbine ◽  
Operating Conditions ◽  
Relative Reduction ◽  
Maximum Deviation ◽  
Heavy Duty ◽  
Flow Distortion ◽  
Local Flow ◽  
Intake System ◽  
Heavy Duty Gas Turbine ◽  
Industrial Gas Turbine

An important loss in an industrial gas turbine is caused by the intake system. Even though these losses have a direct effect on the performance of the engine, the design of the intake system is dominated by local space restriction. Consequently, intake losses are site specific parameters. They correlate with the airflow velocity and therefore operating conditions of the engine affect the intake performance. But due to the high experimental effort necessary to investigate intake losses, only sparse information about this effect is available. For the present study a typical vertical industrial intake duct was investigated numerically for different operating scenarios. The performance simulation of a single shaft heavy duty gas turbine provided boundary conditions for the CFD (Computational Fluid Dynamics) study of the intake duct. For all operating conditions a large scale vortex developed in the intake plenum and entered the compressor. Bearing support struts caused local flow distortion at the compressor inlet. Even for extreme operating scenarios the relative changes of pressure recovery compared to the design point value were small (0.1%). However, the resulting power change was generally in excess of the intake loss deviation. Applied to a heavy duty gas turbine, the maximum deviation of 0.2% of power was equivalent to about 0.4 MW. In most cases lower pressure losses were predicted which benefited the overall engine performance. For the cold scenario the intake performance deteriorated and resulted in a relative reduction of power of nearly 0.5 MW.

scholarly journals Dynamic Modeling of Single-Shaft Industrial Gas Turbine

1996 ◽  
Author(s):  
R. Bettocchi ◽  
P. R. Spina ◽  
F. Fabbri
Keyword(s):  
Steady State ◽  
Gas Turbine ◽  
Dynamic Modeling ◽  
Operating Conditions ◽  
Steady State Condition ◽  
On Line ◽  
Working Parameters ◽  
Industrial Gas Turbine ◽  
And Control ◽  
Measurement And Control

In the paper the dynamic non-linear model of single shaft industrial gas turbine was developed as the first stage of a methodology aimed at the diagnosis of measurement and control sensors and gas turbine operating conditions. The model was calibrated by means of reference steady-state condition data of a real industrial gas turbine and was used to simulate various machine transients. The model is modular in structure and was carried out in simplified form, but not so as to compromise its accuracy, to reduce the calculation time and thus make it more suitable for on-line simulation. The comparison between values of working parameters obtained by the simulations and measurements during some transients on the gas turbine in operation provided encouraging results.

Extension of Fuel Flexibility by Combining Intelligent Control Methods for Siemens SGT-400 Dry Low Emission Combustion System

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
Kexin Liu ◽  
Phill Hubbard ◽  
Suresh Sadasivuni ◽  
Ghenadie Bulat
Keyword(s):  
Gas Turbine ◽  
Operating Conditions ◽  
Combustion System ◽  
Combustion Dynamics ◽  
Heating Value ◽  
Fuel Flexibility ◽  
Wide Range ◽  
Wobbe Index ◽  
Industrial Gas Turbine ◽  
The Impact

Extension of gas fuel flexibility of a current production SGT-400 industrial gas turbine combustor system is reported in this paper. A SGT-400 engine with hybrid combustion system configuration to meet a customer's specific requirements was string tested. This engine was tested with the gas turbine package driver unit and the gas compressor-driven unit to operate on and switch between three different fuels with temperature-corrected Wobbe index (TCWI) varying between 45 MJ/m3, 38 MJ/m3, and 30 MJ/m3. The alteration of fuel heating value was achieved by injection or withdrawal of N2 into or from the fuel system. The results show that the engine can maintain stable operation on and switching between these three different fuels with fast changeover rate of the heating value greater than 10% per minute without shutdown or change in load condition. High-pressure rig tests were carried out to demonstrate the capabilities of the combustion system at engine operating conditions across a wide range of ambient conditions. Variations of the fuel heating value, with Wobbe index (WI) of 30 MJ/Sm3, 33 MJ/Sm3, 35 MJ/Sm3, and 45 MJ/Sm3 (natural gas, NG) at standard conditions, were achieved by blending NG with CO2 as diluent. Emissions, combustion dynamics, fuel pressure, and flashback monitoring via measurement of burner metal temperatures, were the main parameters used to evaluate the impact of fuel flexibility on combustor performance. Test results show that NOx emissions decrease as the fuel heating value is reduced. Also note that a decreasing fuel heating value leads to a requirement to increase the fuel supply pressure. Effect of fuel heating value on combustion was investigated, and the reduction in adiabatic flame temperature and laminar flame speed was observed for lower heating value fuels. The successful development program has increased the capability of the SGT-400 standard production dry low emissions (DLE) burner configuration to operate with a range of fuels covering a WI corrected to the normal conditions from 30 MJ/N·m3 to 49 MJ/N·m3. The tests results obtained on the Siemens SGT-400 combustion system provide significant experience for industrial gas turbine burner design for fuel flexibility.

Sign in / Sign up

Export Citation Format

Share Document