The Effect of Working Fluid Inventory on the Performance of Revolving Helically Grooved Heat Pipes

2000 ◽  
Vol 123 (1) ◽  
pp. 120-129 ◽  
Author(s):  
R. Michael Castle ◽  
Scott K. Thomas ◽  
Kirk L. Yerkes
Keyword(s):  
Heat Pipe ◽  
Heat Pipes ◽  
Working Fluid ◽  
Maximum Heat ◽  
Limit Model ◽  
Filling Station ◽  
Capillary Limit ◽  
Helical Groove ◽  
Wick Structure ◽  
Evaporative Heat Transfer

The results of a recently completed experimental and analytical study showed that the capillary limit of a helically-grooved heat pipe (HGHP) was increased significantly when the transverse body force field was increased. This was due to the geometry of the helical groove wick structure. The objective of the present research was to experimentally determine the performance of revolving helically-grooved heat pipes when the working fluid inventory was varied. This report describes the measurement of the geometry of the heat pipe wick structure and the construction and testing of a heat pipe filling station. In addition, an extensive analysis of the uncertainty involved in the filling procedure and working fluid inventory has been outlined. Experimental measurements include the maximum heat transport, thermal resistance and evaporative heat transfer coefficient of the revolving helically grooved heat pipe for radial accelerations of |a⃗r|=0.0, 2.0, 4.0, 6.0, 8.0, and 10.0-g and working fluid fills of G=0.5, 1.0, and 1.5. An existing capillary limit model was updated and comparisons were made to the present experimental data.

Effect of Fluid Loading on the Performance of Wicked Heat Pipes

Volume 3 ◽  
2004 ◽  
Author(s):  
R. Kempers ◽  
A. Robinson ◽  
C. Ching ◽  
D. Ewing
Keyword(s):  
Heat Flux ◽  
Heat Pipe ◽  
Heat Transport ◽  
Heat Pipes ◽  
Working Fluid ◽  
Fluid Loading ◽  
Maximum Heat ◽  
Horizontal Orientation ◽  
Maximum Heat Flux ◽  
Dry Out

A study was performed to experimentally characterize the effect of fluid loading on the heat transport performance of wicked heat pipes. In particular, experiments were performed to characterize the performance of heat pipes with insufficient fluid to saturate the wick and excess fluid for a variety of orientations. It was found that excess working fluid in the heat pipe increased the thermal resistance of the heat pipe, but increased maximum heat flux through the pipe in a horizontal orientation. The thermal performance of the heat pipe was reduced when the amount of working fluid was less than required to saturate the wick, but the maximum heat flux through the heat pipe was significantly reduced at all orientations. It was also found in this case the performance of this heat pipe deteriorated once dry-out occurred.

Operational Limitations of Heat Pipes With Silver-Water Nanofluids

2013 ◽  
Vol 135 (11) ◽  
Author(s):  
Lazarus Godson Asirvatham ◽  
Rajesh Nimmagadda ◽  
Somchai Wongwises
Keyword(s):  
Silver Nanoparticles ◽  
Heat Pipe ◽  
Heat Load ◽  
Operating Temperature ◽  
Particle Diameter ◽  
Heat Pipes ◽  
Working Fluid ◽  
Limit Value ◽  
Capillary Limit ◽  
Nanoparticles Concentration

The paper presents the enhancement in the operational limits (boiling, entrainment, sonic, viscous and capillary limits) of heat pipes using silver nanoparticles dispersed in de-ionized (DI) water. The tested nanoparticles concentration ranged from 0.003 vol. % to 0.009 vol. % with particle diameter of <100 nm. The nanofluid as working fluid enhances the effective thermal conductivity of heat pipe by 40%, 58%, and 70%, respectively, for volume concentrations of 0.003%, 0.006%, and 0.009%. For an input heat load of 60 W, the adiabatic vapor temperatures of nanofluid based heat pipes are reduced by 9 °C, 18 °C, and 20 °C, when compared with DI water. This reduction in the operating temperature enhances the thermophysical properties of working fluid and gives a change in the various operational limits of heat pipes. The use of silver nanoparticles with 0.009 vol. % concentration increases the capillary limit value of heat pipe by 54% when compared with DI water. This in turn improves the performance and operating range of the heat pipe.

scholarly journals Thermal analysis of heat pipe using self rewetting fluids

2011 ◽  
Vol 15 (3) ◽  
pp. 879-888 ◽  
Author(s):  
Rathinasamy Senthilkumar ◽  
Subaiah Vaidyanathan ◽  
Sivaramanb Balasubramanian
Keyword(s):  
Surface Tension ◽  
Heat Pipe ◽  
Heat Transport ◽  
Pure Water ◽  
Heat Pipes ◽  
The Self ◽  
Working Fluid ◽  
Surface Tension Gradient ◽  
Condenser Section ◽  
Maximum Heat

This paper discuses the use of self rewetting fluids in the heat pipe. In conventional heat pipes, the working fluid used has a negative surface-tension gradient with temperature. It is an unfavourable one and it decreases the heat transport between the evaporator section and the condenser section. Self rewetting fluids are dilute aqueous alcoholic solutions which have the number of carbon atoms more than four. Unlike other common liquids, self-rewetting fluids have the property that the surface tension increases with temperature up to a certain limit. The experiments are conducted to improve the heat-transport capability and thermal efficiency of capillary assisted heat pipes with the self rewetting fluids like aqueous solutions of n-Butanol and n-Pentanol and its performance is compared with that of pure water. The n-Butanol and n-Pentanol are added to the pure water at a concentration of 0.001moles/lit to prepare the self rewetting fluids. The heat pipes are made up of copper container with a two-layered stainless steel wick consisting of mesh wrapped screen. The experimental results show that the maximum heat transport of the heat pipe is enhanced and the thermal resistances are considerably decreased than the traditional heat pipes filled with water. The fluids used exhibit an anomalous increase in the surface tension with increasing temperature.

Experimental Model to Optimize the Design of Cylindrical Heat Pipes for Solar Collector Application

2013 ◽  
Vol 393 ◽  
pp. 735-740
Author(s):  
Fairosidi Idrus ◽  
Nazri Mohamad ◽  
Ramlan Zailani ◽  
Wisnoe Wirachman ◽  
Mohd Zulkifly Abdullah
Keyword(s):  
Heat Pipe ◽  
Thermal Performance ◽  
Heat Pipes ◽  
Design Parameters ◽  
Working Fluid ◽  
Pipe Material ◽  
Efficient Design ◽  
Wick Structure ◽  
To Come ◽  
Transfer Device

A heat pipe is a heat-transfer device that use the principles of thermal conductivity and phase change to transfer heat between two ends at almost constant temperature. The thermal peformance of cylindrical heat pipes depends on design parameters such as dimensions of the heat pipe, material, wick structure and the working fluid. An experimental strategy was designed to study the effect of these parameters on the thermal performance of cylindrical heat pipes. The experimental design was conceived by employing the Taguchi method. The final aim of the experiments is to come up with design parameters that will yield optimum thermal performance. This paper presents an efficient design of experiment and the associated experimental setup and procedures to be carried out in order to optimize the design of cylindrical heat pipes.

An Experimental Investigation on Micro Heat Pipe with a Trapezium-Grooved Wick Structure

2010 ◽  
Vol 29-32 ◽  
pp. 1695-1700
Author(s):  
Shi Gang Wang ◽  
Xi Bing Li ◽  
Bai Rui Tao ◽  
Hong Xia Zhang
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Heat Pipe ◽  
Optimum Design ◽  
Heat Pipes ◽  
Micro Heat Pipe ◽  
Capillary Limit ◽  
Heat Transfer Capacity ◽  
Wick Structure ◽  
Micro Heat Pipes

Through combination of experimental investigation with theoretical optimum design, this paper determined the crucial factors in affecting the heat transfer capacity in micro heat pipes with a trapezium-grooved wick structure are capillary limit and entrainment limit, and verified the validity of the heat transfer models thus built.

Impact of Micropillar Density Distribution on the Capillary Limit of Heat Pipes

2020 ◽  
Author(s):  
Doriane Ibtissam Hassaine Daoudji ◽  
Quentin Struss ◽  
Amrid Amnache ◽  
Étienne Léveillé ◽  
Mahmood Reza Salim Shirazy ◽  
...  
Keyword(s):  
Density Distribution ◽  
Heat Pipe ◽  
Pressure Loss ◽  
Performance Enhancement ◽  
Heat Pipes ◽  
Theoretical Models ◽  
Capillary Limit ◽  
Pillar Density ◽  
Wick Structure ◽  
Viscous Pressure

Abstract This paper shows the performance enhancement of heat pipes by tailoring the density distribution of micropillar wicks to minimize viscous pressure loss while maintaining sufficient capillary pumping. In a heat pipe, capillarity and permeability are linked, since small pores create higher capillary pumping while unfortunately inducing more pressure drop along the heat pipe. This pressure loss accumulates along the heat pipe, leading to a non-uniform pressure difference between the liquid and vapor. Therefore, we do not need a uniform capillary pressure to withstand this difference. This provides the opportunity to spatially tailor the wick structure, aiming for a high capillarity to pump the liquid, but a low permeability to induce less pressure loss. Our study offers a compromise between capillarity and permeability by designing the density distribution of the pillar wick structure. This density distribution, which was not studied before, will be shown to enhance the heat pipe performance. The theoretical models show that a tailored density distribution can enhance the heat pipe performance by a factor of 1.5. To support this result, ‘rate of rise’ measurements along a pillar array demonstrate that the liquid pressure loss in a tailored density array are less compared to a constant pillar density.

A Titanium Based Flat Heat Pipe

2008 ◽  
Author(s):  
Changsong Ding ◽  
Gaurav Soni ◽  
Payam Bozorgi ◽  
Brian Piorek ◽  
Carl D. Meinhart ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Aspect Ratio ◽  
Heat Pipe ◽  
Carrying Capacity ◽  
High Aspect Ratio ◽  
Capillary Flow ◽  
Titanium Substrate ◽  
Heat Pipes ◽  
Working Fluid ◽  
Wick Structure

We are developing innovative heat pipes based on Nano-Structured Titania (NST) with a potential for high heat carrying capacity and high thermal conductivity. These heat pipes have a flat geometry as opposed to a cylindrical geometry found in conventional heat pipes. The flatness will enable a good contact with microprocessor chips and thus reduce the thermal contact resistance. We refer to it as a Thermal Ground Plane (TGP) because of its flat and thin geometry. It will provide the ability to cool the future generations of power intensive microprocessor chips and circuit boards in an efficient way. It also brings the potential to function in high temperature (&gt;150°C) fields because of its high yield strength and compatibility [1]. The TGP is fabricated with Titanium. It adopts the recently developed high aspect ratio Ti processing techniques [2] and laser packaging techniques. The three main components of the TGP are 1) a fine wick structure based on arrays of high aspect ratio Ti pillars and hair like structures of Nano-Structured Titania (NST), 2) A shallow Ti cavity welded onto the wick structure and 3) the working fluid, water, sealed between the cavity and the wick. The heat carrying capacity and the thermal conductivity of a heat pipe are generally determined by the speed of capillary flow of the working fluid through its wick. The TGP wick has the potential to generate high flow rates and to meet the growing challenges faced by electronics cooling community. The TGP wick structure, developed by etching high aspect ratio pillars in a titanium substrate and growing nano scale hairs on the surface of the pillars, is super hydrophilic and capable of wicking water at velocities ∼ 10−2 m/s over distances of several centimeters. The thermal conductivity of the current TGP device was measured to be k = 350 W/m·K. The completed TGP device has the potential of attaining a higher conductivity by improving the wicking material and of carrying higher power density. Washburn equation [3] for dynamics of capillary flow has been employed to explain the results of our experiments. The experiment shows a good agreement with Washburn equation.

Steady State Modeling of a Rotating Heat Pipe With a Composite Wick Structure

Volume 3 ◽  
2004 ◽  
Author(s):  
T. A. Jankowski ◽  
J. A. Waynert ◽  
F. C. Prenger ◽  
A. Razani
Keyword(s):  
Steady State ◽  
Heat Pipe ◽  
Heat Pipes ◽  
Working Fluid ◽  
Round Cross Section ◽  
State Heat ◽  
Pipe Model ◽  
Axis Of Rotation ◽  
Wick Structure ◽  
Steady State Heat

A steady state heat pipe model, capable of calculating temperature and pressure distributions in the working fluid of a rotating heat pipe, is described here. The model can predict the performance of rotating heat pipes with a round cross-section, containing an annular gap composite wick structure. In addition to straight heat pipes, with a longitudinal axis that may or may not coincide with the axis of rotation, the model also allows for simulation of bent heat pipes. Using this model, results are generated for a bent heat pipe proposed for use in cooling rotating machinery. For the bent heat pipe, the condenser and adiabatic sections coincide with the axis of rotation, while the evaporator consists of an off-axis eccentrically rotating component, and a bend that allows for portion of the evaporator to be nearly perpendicular to the axis of rotation. The presence of the composite wick allows for heat pipe operation in both the rotating and stationary operating modes. Model results for the stationary operating mode compare favorably to the steady state heat pipe analysis code HTPIPE [1]. These comparisons for the stationary operating limit are significant, since HTPIPE has been benchmarked against experimental heat pipe data for nearly 30 years. As the rotational speed is increased, the rotation induced forces are used to drive the liquid flow to the evaporator. At high rotation rates, the liquid recedes from the wick, and forms a thin layer against the inside wall of the heat pipe. The results show that when a stable liquid layer is formed against the wall of the pipe, the shear stress opposes the rotation induced forces acting on the liquid, and limits the magnitude of the pressure and temperature rises in the working fluid (from the values predicted using a hydrostatic approximation).

scholarly journals Experimental investigations and optimization of process parameters of meshed-wick heat pipe

2020 ◽  
Vol 184 ◽  
pp. 01026 ◽  
Author(s):  
B.Ch Nookaraju ◽  
B. Hemanth Sai ◽  
K.V.N.S Himakar ◽  
N. Limba Reddy ◽  
N Sateesh
Keyword(s):  
Heat Transfer ◽  
Thermal Analysis ◽  
Heat Pipe ◽  
Heat Pipes ◽  
Working Fluid ◽  
Outer Diameter ◽  
Cylindrical Shape ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Screen Mesh

Heat pipes are used to transfer heat, which are hollow cylindrical shape device filled with small amount of working fluid, which can change its phase. The rate of heat transfer in heat pipes compared to normal heat exchanging devices is more. Depending on the applications of heat transfer various heat pipes are being designed. Methanol fluid is used with 50% fill ratio. It is made of copper with outer diameter of 15.88mm and inner diameter of 14.88mm. It consists of a screen mesh made of copper powder inside it with thickness of 0.5mm. Due to heat input methanol changes its phase from liquid to vapor. The vapor loses its heat and changes its phase back to liquid in the condenser. At the condenser section the vapour gives up it heat and changes its phase from vapour to liquid. The screen mesh assists the flow of condensed working fluid through capillary action. Optimized the results by “Taguchi method” using “Minitab software”. The Thermal analysis was done with the optimum conditions, which were obtained as a result from the optimization method by Ansys Fluent software. Then finally compared the thermal parameters obtained from experiments with the Thermal analysis result. It is found the maximum heat transfer rate is optimized using meshed wick heat pipe conditions.

Investigation of Heat Pipe Drilling Application

2004 ◽  
Author(s):  
Tien-Chien Jen ◽  
Yau Min Chen ◽  
Fern Tuchowski
Keyword(s):  
Heat Pipe ◽  
Experimental Studies ◽  
Heat Pipes ◽  
Cutting Fluid ◽  
Working Fluid ◽  
Federal State ◽  
Hole Making ◽  
Wick Structure ◽  
The Operating Mechanism ◽  
State And Local

It’s widely known that hole making is, by a significant margin, the most frequently performed process among metalworking operations. It’s also among the most difficult operations to control from a thermal perspective. The most common cooling method is the use of cutting fluids flooding through the cutting zone. However, disposal of the used fluids is subject to federal, state and local laws and regulations. More stringent regulations in environmental pollution are expected in the future, we can expect the cost associated with coolants to continue to rise. Experimental studies implementing the use of a heat pipe to cool the drill and thus reduce the amount of cutting fluid required have been recently conducted. The heat pipe works with no moving parts or electronics and it also offers an effective alternative to removing heat without significant increases in operating temperatures. The operating mechanism of heat pipes have been extensively studied, however, rotating heat pipes with a wick structure has not received adequate attention in the past. In this study, a numerical analysis has been conducted to model the flow in an axially rotating heat pipe. The result shows the transport capacity is strongly affected by changes in the thermal physical properties of the working fluid with the temperature. The rotating speeds have strong effect in the vapor core but this effect is weak in the liquid flow of the wick structure.

Sign in / Sign up

Export Citation Format

Share Document