Numerical Study of a Rotary Lip Seal With a Quasi-Random Sealing Surface

2000 ◽  
Vol 123 (3) ◽  
pp. 517-524 ◽  
Author(s):  
Fanghui Shi ◽  
Richard F. Salant
Keyword(s):  
Friction Coefficient ◽  
Physical Mechanism ◽  
Periodic Structures ◽  
Numerical Study ◽  
Thickness Distribution ◽  
Operating Characteristics ◽  
Pumping Rate ◽  
Lip Seal ◽  
Pressure Distributions ◽  
Reverse Pumping

In all previous numerical simulations of the rotary lip seal, the sealing surface was modeled by regular periodic structures. In the present study, a more realistic quasirandom surface is used. A mixed elastohydrodynamic analysis is used to generate predictions of such seal operating characteristics as friction coefficient, reverse pumping rate, film thickness distribution, hydrodynamic and contact pressure distributions, contact area, and cavitation area. The results are in qualitative agreement with previous experimental observations. In the course of the simulations, a new physical mechanism of reverse pumping has been identified.

Soft Elastohydrodynamic Analysis of Radial Lip Seals With Deterministic Microasperities on the Shaft

2007 ◽  
Vol 129 (4) ◽  
pp. 851-859 ◽  
Author(s):  
Philip C. Hadinata ◽  
Lyndon Scott Stephens
Keyword(s):  
Friction Coefficient ◽  
Load Capacity ◽  
Asperity Height ◽  
Pumping Rate ◽  
Simultaneous Reduction ◽  
Lip Seal ◽  
Lip Seals ◽  
Lubrication Characteristics ◽  
Triangular Design ◽  
Reverse Pumping

A numerical analysis is conducted to investigate the elastohydrodynamic effect of deterministic microasperities on the shaft of a lip seal. Various geometries of microasperities (triangular, square, hexagonal, and circular) are put into a 100×100μm2 unit cell and are investigated using Reynolds equation. For each shape, the area fraction of the microasperity is varied between 0.2 and 0.8, and the asperity height is varied between 0.3μm and 5μm. The calculation for load capacity and friction coefficient indicates that there are values for asperity height, where the load capacity and friction coefficient are optimized. These optimum heights were reached at 1–3μm. Although the lip seal surface is considered to be smooth, reverse pumping can still be obtained using an oriented triangular design. The Couette flow rate for this asperity showed lubricant is reverted back toward the seal side 2.6 times more than using a conventional lip seal. The addition of microasperities to the shaft surface shows significant improvement in lubrication characteristics for the lip seal in the form of a simultaneous reduction in friction coefficient and increase in the reverse pumping rate.

Elastohydrodynamic Analysis of Reverse Pumping in Rotary Lip Seals With Microundulations

1994 ◽  
Vol 116 (1) ◽  
pp. 56-62 ◽  
Author(s):  
R. F. Salant ◽  
A. L. Flaherty
Keyword(s):  
Fluid Mechanics ◽  
High Pressures ◽  
Elastic Behavior ◽  
Pumping Rate ◽  
Dynamic Conditions ◽  
Lip Seal ◽  
Lubricating Film ◽  
Lip Seals ◽  
Reverse Pumping

An elastohydrodynamic analysis of a rotary lip seal containing microundulations, incorporating both the fluid mechanics of the lubricating film and the elastic behavior of the lip, has been performed numerically. The results indicate that, under dynamic conditions, the undulation pattern deforms such that it produces reverse pumping. The reverse pumping rate is substantial, and overwhelms the natural leakage induced by the sealed pressure, thereby preventing leakage through the seal. The results also show that the undulations hydrodynamically generate sufficiently high pressures, within the film, to provide load support and maintain the integrity of the film.

Thermal Elastohydrodynamic Model of a Radial Lip Seal—Part I: Analysis and Base Results

1999 ◽  
Vol 121 (1) ◽  
pp. 1-10 ◽  
Author(s):  
Kevin Day ◽  
Richard F. Salant
Keyword(s):  
Cross Sections ◽  
Thickness Distribution ◽  
Temperature Dependent ◽  
Pumping Rate ◽  
Lip Seal ◽  
Lubricating Film ◽  
Model Predictions ◽  
Dependent Model ◽  
Temperature Dependent Model ◽  
Shaft Surface

A numerical thermal elastohydrodynamic model of a radial lip seal, with a flooded air side, has been constructed. The shaft surface is modeled as perfectly smooth, while the lip microgeometry is modeled as a uniform distribution of asperities with initially circular cross-sections. The asperities can deform circumferentially as the bulk lip material shears. Both the viscosity of the fluid and the elastic modulus of the lip are temperature dependent. Model predictions include the pressure distribution in the lubricating film under the lip, the film thickness distribution, the cavitation distribution, the pumping rate, and the lip temperature distribution.

scholarly journals A numerical study of glacier advance over deforming till

2010 ◽  
Vol 4 (3) ◽  
pp. 359-372 ◽  
Author(s):  
G. J.-M. C. Leysinger Vieli ◽  
G. H. Gudmundsson
Keyword(s):  
Effective Viscosity ◽  
Numerical Study ◽  
Thickness Distribution ◽  
Plug Flow ◽  
Linear Wave ◽  
Sediment Layer ◽  
Mixed Flow ◽  
Model Experiments ◽  
Non Linear ◽  
Glacier Advance

Abstract. The advance of a glacier over a deforming sediment layer is analysed numerically. We treat this problem as a contact problem involving two slowly-deforming viscous bodies. The surface evolution of the two bodies, and of the contact interface between them, is followed through time. Using various different non-linear till rheologies, we show how the mode of advance depends on the relative effective viscosities of ice and till. Three modes of advances are observed: (1) overriding, where the glacier advances through ice deformation only and without deforming the sediment; (2) plug-flow, where the sediment is strongly deformed, the ice moves forward as a block and a bulge is built in front of the glacier; and (3) mixed-flow, where the glacier advances through both ice and sediment deformation. For the cases of both overriding and mixed-flow, an inverse depth-age relationship within the ice is obtained. A series of model experiments show the contrast in effective viscosity between ice and till to be the single most important model parameter defining the mode of advance and the resulting thickness distribution of the till. Our model experiments indicate that the thickness of the deforming till layer is greatest close to the glacier front. Measurements of till thickness taken in such locations may not be representative of deforming till thickness elsewhere. Given sufficiently large contrast in effective viscosity between ice and till, a sediment bulge is formed in front of the glacier. During glacier advance, the bulge quickly reaches a steady state form strongly resembling single-crested push moraines. Inspection of particle paths within the sediment bulge, shows that particles within the till travel at a different speed from the bulge itself, and the push moraine to advance as a form-conserving non-linear wave.

PRELIMINARY STUDY ON NOVEL BEAM-TO-COLUMN CONNECTION BASED ON SMA PLATE

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Michael CH Yam ◽  
Ke Ke ◽  
Ping Zhang ◽  
Qingyang Zhao
Keyword(s):  
Friction Coefficient ◽  
Energy Dissipation ◽  
Numerical Study ◽  
Numerical Models ◽  
Numerical Technique ◽  
The Self ◽  
Hysteretic Behavior ◽  
The Novel ◽  
Energy Dissipation Capacity ◽  
Preliminary Study

A novel beam-to-column connection equipped with shape memory alloy (SMA) plates has been proposed to realize resilient performance under low-to-medium seismic actions. In this conference paper, the detailed 3D numerical technique calibrated by the previous paper is adopted to examine the hysteretic behavior of the novel connection. A parametric study covering a reasonable range of parameters including the thickness of the SMA plate, friction coefficient between SMA plate and beam flange and pre-load of the bolt was carried out and the influence of the parameters was characterized. In addition, the effect of the SMA Belleville washer on the connection performance was also studied. The results of the numerical study showed that the initial connection stiffness and the energy-dissipation capacity of the novel connection can be enhanced with the increase of the thickness of the SMA plate. In addition, the initial connection stiffness and energy-dissipation behavior of the novel connection can be improved by increasing the friction coefficient or pre-load of bolts, whereas the increased friction level could compromise the self-centering behavior of the connection. The hysteretic curves of the numerical models of the connection also implied that the SMA washers may contribute to optimizing the connection behavior by increasing the connection stiffness and energy-dissipation capacity without sacrificing the self-centering behavior.

scholarly journals A Parameter Study of Localization

1996 ◽  
Vol 3 (1) ◽  
pp. 1-10 ◽  
Author(s):  
Sandor Stephen Mester ◽  
Haym Benaroya
Keyword(s):  
Periodic Structures ◽  
Numerical Study ◽  
Vibration Characteristics ◽  
Periodic Pattern ◽  
Parameter Study ◽  
Structural Damping ◽  
One Dimensional

Extensive work has been done on the vibration characteristics of perfectly periodic structures. Disorder in the periodic pattern has been found to lead to localization in one-dimensional periodic structures. It is important to understand localization because it causes energy to be concentrated near the disorder and may cause an overestimation of structural damping. A numerical study is conducted to obtain a better understanding of localization. It is found that any mode, even the first, can localize due to the presence of small imperfections.

scholarly journals Особенности релаксации тензора напряжения в микроскопическом объеме нематической фазы под действием сильного электрического поля

2018 ◽  
Vol 60 (2) ◽  
pp. 405
Author(s):  
А.В. Захаров
Keyword(s):  
Dissipation Rate ◽  
Periodic Structures ◽  
Numerical Study ◽  
Strong Electric Field ◽  
Rectangular Channel ◽  
Energy Dissipation Rate ◽  
Director Field ◽  
Rotational Displacement ◽  
Nonlinear Generalization ◽  
Angle Alpha

AbstractA numerical study of new regimes of reorientation of director field n̂ , velocity v , and components of stress tensor σ_ ij ( ij = x , y , z ) of nematic liquid crystal (LC) encapsulated in a rectangular channel under the action of a strong electric field E directed at angle $$\alpha \left( {\sim\frac{\pi } {2}} \right)$$ α ( ∼ π 2 ) to the horizontal surfaces bounding the LC channel is proposed. The numerical calculations performed in the framework of nonlinear generalization of the classical Eriksen-Leslie theory have shown that at certain relations between the torques and momenta affecting the unit LC volume and E ≫ E _th, transition periodic structures can emerge during reorientation of n̂ , if the corresponding distortion mode has the fastest response, and, thus, suppress all other modes. Rotating domains originating within this process decrease the energy dissipation rate and create more favorable regimes of the director field reorientation, as compared with the uniform rotational displacement.

Hydrodynamic Analysis of the Flow in a Rotary Lip Seal Using Flow Factors

2004 ◽  
Vol 126 (1) ◽  
pp. 156-161 ◽  
Author(s):  
Richard F. Salant ◽  
Ann H. Rocke
Keyword(s):  
Flow Field ◽  
Pressure Distribution ◽  
Reynolds Equation ◽  
Present Approach ◽  
Operating Parameters ◽  
Pumping Rate ◽  
Hydrodynamic Analysis ◽  
Lip Seal ◽  
Lubricating Film ◽  
Computationally Intensive

The flow field in the lubricating film of a rotary lip seal is analyzed numerically by solving the Reynolds equation with flow factors. The behavior of such a flow field is dominated by the asperities on the lip surface. Since previous analyses treated those asperities deterministically, they required very large computation times. The present approach is much less computationally intensive because the asperities are treated statistically. Since cavitation and asperity orientation play important roles, these are taken into account in the computation of the flow factors. Results of the analysis show how the operating parameters of the seal and the characteristics of the asperities affect such seal characteristics as the pressure distribution in the film, the pumping rate and the load support.

scholarly journals A Mixed-Fidelity Numerical Study for Fan–Distortion Interaction

2018 ◽  
Vol 140 (9) ◽  
Author(s):  
Yunfei Ma ◽  
Jiahuan Cui ◽  
Nagabhushana Rao Vadlamani ◽  
Paul Tucker
Keyword(s):  
Immersed Boundary Method ◽  
Numerical Study ◽  
Immersed Boundary ◽  
Fan Performance ◽  
Inlet Distortion ◽  
Eddy Simulation ◽  
Pressure Distributions ◽  
Large Eddy ◽  
Dynamics Method ◽  
Good Agreement

Inlet distortion often occurs under off-design conditions when a flow separates within an intake and this unsteady phenomenon can seriously impact fan performance. Fan–distortion interaction is a highly unsteady aerodynamic process into which high-fidelity simulations can provide detailed insights. However, due to limitations on the computational resource, the use of an eddy resolving method for a fully resolved fan calculation is currently infeasible within industry. To solve this problem, a mixed-fidelity computational fluid dynamics method is proposed. This method uses the large Eddy simulation (LES) approach to resolve the turbulence associated with separation and the immersed boundary method (IBM) with smeared geometry (IBMSG) to model the fan. The method is validated by providing comparisons against the experiment on the Darmstadt Rotor, which shows a good agreement in terms of total pressure distributions. A detailed investigation is then conducted for a subsonic rotor with an annular beam-generating inlet distortion. A number of studies are performed in order to investigate the fan's influence on the distortions. A comparison to the case without a fan shows that the fan has a significant effect in reducing distortions. Three fan locations are examined which reveal that the fan nearer to the inlet tends to have a higher pressure recovery. Three beams with different heights are also tested to generate various degrees of distortion. The results indicate that the fan can suppress the distortions and that the recovery effect is proportional to the degree of inlet distortion.

A Single Server Retrial Queueing System with Two Types of Batch Arrivals

2016 ◽  
pp. 55-70
Author(s):  
Kalyanaraman Rathinasabapathy
Keyword(s):  
Queueing System ◽  
Numerical Study ◽  
Priority Queue ◽  
Single Server ◽  
Type I ◽  
Type Ii ◽  
Operating Characteristics ◽  
Batch Arrivals ◽  
Retrial Queueing System ◽  
Retrial Queueing

A retrial queueing system with two types of batch arrivals is considered. The arrivals are called type I and type II customers. The type I customers arrive in batches of size k with probability c_k and type II customers arrive in batches of size k with probability d_k. Service time distributions are identical independent distributions and are different for both type of customers. If the arriving customers are blocked due to server being busy, type I customers are queued in a priority queue of infinity capacity whereas type II customers entered into retrial group in order to seek service again after a random amount of time. For this model the joint distribution of the number of customers in the priority queue and in the retrial group in closed form is obtained. Some particular models and operating characteristics are obtained. A numerical study is also carried out.

Sign in / Sign up

Export Citation Format

Share Document