Variations in Upstream Vane Loading With Changes in Back Pressure in a Transonic Compressor

1998 ◽  
Vol 122 (3) ◽  
pp. 433-441 ◽  
Author(s):  
Douglas P. Probasco ◽  
Tim J. Leger ◽  
J. Mitch Wolff ◽  
William W. Copenhaver ◽  
Randall M. Chriss
Keyword(s):  
Surface Pressure ◽  
Guide Vane ◽  
Pressure Fluctuations ◽  
Back Pressure ◽  
Bow Shock ◽  
Navier Stokes ◽  
Inlet Guide Vane ◽  
Transonic Compressor ◽  
Unsteady Surface Pressure ◽  
Upstream Pressure

Dynamic loading of an inlet guide vane (IGV) in a transonic compressor is characterized by unsteady IGV surface pressures. These pressure data were acquired for two spanwise locations at a 105 percent speed operating condition, which produces supersonic relative Mach numbers over the majority of the rotor blade span. The back pressure of the compressor was varied to determine the effects from such changes. Strong bow shock interaction was evident in both experimental and computational results. Variations in the back pressure have significant influence on the magnitude and phase of the upstream pressure fluctuations. The largest unsteady surface pressure magnitude, 40 kPa, was obtained for the near-stall mass flow condition at 75 percent span and 95 percent chord. Radial variation effects caused by the spanwise variation in relative Mach number were measured. Comparisons to a two-dimensional nonlinear unsteady blade/vane Navier–Stokes analysis show good agreement for the 50 percent span results in terms of IGV unsteady surface pressure. The results of the study indicate that significant nonlinear bow shock influences exist on the IGV trailing edge due to the downstream rotor shock system. [S0889-504X(00)00303-2]

Variations in Upstream Vane Loading With Changes in Back Pressure in a Transonic Compressor

1998 ◽  
Author(s):  
Douglas P. Probasco ◽  
J. Mitch Wolff ◽  
William W. Copenhaver ◽  
Randall M. Chriss
Keyword(s):  
Surface Pressure ◽  
Guide Vane ◽  
Pressure Fluctuations ◽  
Back Pressure ◽  
Bow Shock ◽  
Navier Stokes ◽  
Inlet Guide Vane ◽  
Transonic Compressor ◽  
Unsteady Surface Pressure ◽  
Non Linear

Dynamic loading of an inlet guide vane (IGV) in a transonic compressor is characterized by unsteady IGV surface pressures. This pressure data was acquired for two spanwise locations at a 105% speed operating condition, which produces supersonic relative Mach numbers over the majority of the rotor blade span. The back pressure of the compressor was varied to determine the effects from such changes. Strong bow shock interaction was evident in both experimental and computational results. Variations in the back pressure have significant influence on the magnitude and phase of the upstream pressure fluctuations. The largest unsteady surface pressure magnitude, 40 kPa, was obtained for the near stall mass flow condition at 75% span and 95% chord. Radial variation effects caused by the spanwise variation in relative Mach number were measured. Comparisons to a two-dimensional non-linear unsteady blade/vane Navier-Stokes analysis shows good agreement for the 50% span results in terms of IGV unsteady surface pressure. The results of the study indicate that significant non-linear bow shock influences exist on the IGV trailing edge due to the downstream rotor shock system.

Transonic Compressor Influences on Upstream Surface Pressures With Axial Spacing

1999 ◽  
Author(s):  
Peter J. Koch ◽  
Douglas P. Probasco ◽  
J. Mitch Wolff ◽  
William W. Copenhaver ◽  
Randall M. Chriss
Keyword(s):  
Surface Pressure ◽  
High Speed ◽  
Guide Vane ◽  
Navier Stokes ◽  
Inlet Guide Vane ◽  
Transonic Compressor ◽  
Unsteady Surface Pressure ◽  
Blade Row ◽  
Non Linear ◽  
Unsteady Loading

A set of inlet guide vane (IGV) unsteady surface pressure measurements is presented. The unsteady aerodynamic effects of a highly loaded, high speed downstream compression stage on the upstream inlet guide vane stator surface pressures are characterized through experimental and computational analysis. The axial spacing between the IGV and rotor was varied between 12%, 26%, and 56% of the IGV chord for a 105% speed, peak efficiency operating condition, which is transonic. Unsteady IGV surface pressures were acquired for two spanwise locations on both blade surfaces. The largest unsteady surface pressure magnitudes were obtained at the 12% axial spacing configuration and 95% chord location. In general, spanwise variations were found to be important. The upstream bow shock effect is non-linear in character. Comparisons to a two-dimensional, non-linear unsteady multi-blade row Navier-Stokes analysis at 50% span show a good agreement with the IGV unsteady surface pressure results and higher harmonic content. The results of the study indicate significant variations in the IGV unsteady loading caused by changes in axial spacing.

IGV-Rotor Interaction Analysis in a Transonic Compressor Using the Navier-Stokes Equations

1996 ◽  
Author(s):  
Andrea Arnone ◽  
Roberto Pacciani
Keyword(s):  
Stokes Equations ◽  
Interaction Analysis ◽  
Guide Vane ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Inlet Guide Vane ◽  
Operating Characteristics ◽  
Navier Stokes Equations ◽  
Transonic Compressor ◽  
Mass Flow Rates

A recently developed, time-accurate multigrid viscous solver has been extended to handle quasi-three-dimensional effects and applied to the first stage of a modern transonic compressor. Interest is focused on the inlet guide vane (IGV):rotor interaction where strong sources of unsteadiness are to be expected. Several calculations have been performed to predict the stage operating characteristics. Flow structures at various mass flow rates, from choke to near stall, are presented and discussed. Comparisons between unsteady and steady pitch-averaged results are also included in order to obtain indications about the capabilities of steady, multi-row analyses.

IGV–Rotor Interaction Analysis in a Transonic Compressor Using the Navier–Stokes Equations

1998 ◽  
Vol 120 (1) ◽  
pp. 147-155 ◽  
Author(s):  
A. Arnone ◽  
R. Pacciani
Keyword(s):  
Stokes Equations ◽  
Interaction Analysis ◽  
Guide Vane ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Inlet Guide Vane ◽  
Operating Characteristics ◽  
Navier Stokes Equations ◽  
Transonic Compressor ◽  
Mass Flow Rates

A recently developed, time-accurate multigrid viscous solver has been extended to handle quasi-three-dimensional effects and applied to the first stage of a modern transonic compressor. Interest is focused on the inlet guide vane (IGV)-rotor interaction where strong sources of unsteadiness are to be expected. Several calculations have been performed to predict the stage operating characteristics. Flow structures at various mass flow rates, from choke to near stall, are presented and discussed. Comparisons between unsteady and steady pitch-averaged results are also included in order to obtain indications about the capabilities of steady, multi-row analyses.

Aeroacoustic analysis of slat tones

2021 ◽  
Vol 263 (1) ◽  
pp. 5650-5663
Author(s):  
Hasan Kamliya Jawahar ◽  
Syamir Alihan Showkat Ali ◽  
Mahdi Azarpeyvand
Keyword(s):  
Wavelet Transform ◽  
Surface Pressure ◽  
Wavelet Coefficient ◽  
Pressure Fluctuations ◽  
Low Frequency ◽  
Stream Velocity ◽  
High Lift ◽  
Unsteady Surface Pressure ◽  
Slat Noise ◽  
Generation Mechanisms

Experimental measurements were carried out to assess the aeroacoustic characteristics of a 30P30N high-lift device, with particular attention to slat tonal noise. Three different types of slat modifications, namely slat cove filler, serrated slat cusp, and slat finlets have been experimentally examined. The results are presented for an angle of attack of α = 18 at a free-stream velocity of U = 30 m/s, which corresponds to a chord-based Reynolds number of Re = 7 x 10. The unsteady surface pressure near the slat region and far-field noise were made simultaneously to gain a deeper understanding of the slat noise generation mechanisms. The nature of the low-frequency broadband hump and the slat tones were investigated using higher-order statistical approaches for the baseline 30P30N and modified slat configurations. Continuous wavelet transform of the unsteady surface pressure fluctuations along with secondary wavelet transform of the broadband hump and tones were carried out to analyze the intermittent events induced by the tone generating resonant mechanisms. Stochastic analysis of the wavelet coefficient modulus of the surface pressure fluctuations was also carried out to demonstrate the inherent differences of different tonal frequencies. An understanding into the nature of the noise generated from the slat will help design the new generation of quite high-lift devices.

The Extension of a Solution-Adaptive Three-Dimensional Navier–Stokes Solver Toward Geometries of Arbitrary Complexity

1993 ◽  
Vol 115 (2) ◽  
pp. 283-295 ◽  
Author(s):  
W. N. Dawes
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Centrifugal Impeller ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Wide Range ◽  
Nozzle Guide Vane ◽  
Recent Developments ◽  
Nozzle Guide

This paper describes recent developments to a three-dimensional, unstructured mesh, solution-adaptive Navier–Stokes solver. By adopting a simple, pragmatic but systematic approach to mesh generation, the range of simulations that can be attempted is extended toward arbitrary geometries. The combined benefits of the approach result in a powerful analytical ability. Solutions for a wide range of flows are presented, including a transonic compressor rotor, a centrifugal impeller, a steam turbine nozzle guide vane with casing extraction belt, the internal coolant passage of a radial inflow turbine, and a turbine disk cavity flow.

CFD Computation of Fan Interaction Noise

2007 ◽  
Author(s):  
Sheryl M. Grace ◽  
Douglas L. Sondak ◽  
Daniel J. Dorney ◽  
Michaela Logue
Keyword(s):  
Surface Pressure ◽  
Second Harmonic ◽  
Guide Vane ◽  
Power Level ◽  
Broadband Noise ◽  
Rotor Blades ◽  
Navier Stokes ◽  
Fan Noise ◽  
Guide Vanes ◽  
Blade Passage

In this study, a 3-D, unsteady, Reynolds-averaged Navier-Stokes (RANS) CFD code coupled to an acoustic calculation is used to predict the contribution of the exit guide vanes to tonal fan noise downstream. The configuration investigated is that corresponding to the NASA Source Diagnostic Test (SDT) 22-in fan rig. One configuration from the SDT matrix is considered here: the approach condition, and outlet guide vane count designed for cut-off of the blade passage frequency. In this chosen configuration, there are 22 rotor blades and 54 stator blades. The stators are located 2.5 tip chords downstream of the rotor trailing edge. The RANS computations are used to obtain the spectra of the unsteady surface pressure on the exit guide vanes. The surface pressure at the blade passage frequency and its second harmonic are then integrated together with the Green’s function for an annular duct to obtain the pressure at locations in the duct. Comparison of the computed sound power level at the exhaust plane with experiment show good agreement at the cut-on circumferential mode. The results from this investigation validate the use of the CFD code along with the acoustic model for downstream fan noise predictions. This validation enables future investigations such as the effect of duct variation on the exhaust tonal power level and the validity of using this method for predicting broadband noise levels.

Towards Improved Throughflow Capability: The Use of 3D Viscous Flow Solvers in a Multistage Environment

1990 ◽  
Author(s):  
W. N. Dawes
Keyword(s):  
Experimental Evidence ◽  
Steam Turbine ◽  
Guide Vane ◽  
Navier Stokes ◽  
Flow Properties ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Blade Row ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

A methodology is presented for simulating turbomachinery blade rows in a multistage environment by deploying a standard 3D Navier-Stokes solver simultaneously on a number of blade rows. The principle assumptions are that the flow is steady relative to each blade row individually and that the rows can communicate via inter-row mixing planes. These mixing planes introduce circumferential averaging of flow properties but preserve quite general radial variations. Additionally, each blade can be simulated in 3D or axisymmetrically (in the spirit of throughflow analysis) and a series of axisymmetric rows can be considered together with one 3D row to provide, cheaply, a machine environment for that row. Two applications are presented: a transonic compressor rotor and a steam turbine nozzle guide vane simulated both isolated and as part of a stage. In both cases the behaviour of the blade considered in isolation was different to when considered as part of a stage and in both cases was in much closer agreement with the experimental evidence.

Experimental and Numerical Investigation of the Unsteady Surface Pressure in a Three-Stage Model of an Axial High Pressure Turbine

2004 ◽  
Vol 128 (2) ◽  
pp. 261-272 ◽  
Author(s):  
Carmen E. Kachel ◽  
John D. Denton
Keyword(s):  
High Pressure ◽  
Velocity Field ◽  
Surface Pressure ◽  
Pressure Field ◽  
Pressure Fluctuations ◽  
Pressure Waves ◽  
Stage Model ◽  
Unsteady Pressure ◽  
Unsteady Surface Pressure ◽  
Blade Row

This paper presents the results of a numerical and experimental investigation of the unsteady pressure field in a three-stage model of a high pressure steam turbine. Unsteady surface pressure measurements were taken on a first and second stage stator blade, respectively. The measurements in the blade passage were supplemented by time resolved measurements between the blade rows. The explanation of the origin of the unsteady pressure fluctuations was supported by unsteady three-dimensional computational fluid dynamic calculations of which the most extensive calculation was performed over two stages. The mechanisms affecting the unsteady pressure field were: the potential field frozen to the upstream blade row, the pressure waves originating from changes in the potential pressure field, the convected unsteady velocity field, and the passage vortex of the upstream blade row. One-dimensional pressure waves and the unsteady variation of the pitchwise pressure gradient due to the changing velocity field were the dominant mechanisms influencing the magnitude of the surface pressure fluctuations. The magnitude of these effects had not been previously anticipated to be more important than other recognized effects.

scholarly journals Multi-Objective Optimization in Axial Compressor Design Using a Linked CFD-Solver

2008 ◽  
Author(s):  
Kai Becker ◽  
Martin Lawerenz ◽  
Christian Voß ◽  
Reinhard Mo¨nig
Keyword(s):  
Guide Vane ◽  
Axial Compressor ◽  
Navier Stokes ◽  
Inlet Guide Vane ◽  
Optimization Strategy ◽  
Objective Functions ◽  
Multi Objective Optimization ◽  
Multi Objective ◽  
Flow Information ◽  
Design Variation

In combination with a multi-objective 3D optimization strategy, a linked CFD-solver is presented in this paper, combining 3D-Reynolds-averaged-Navier-Stokes and an inviscid throughflow method. It enables the adjustment of the 3D boundary conditions for any design variation and contains new options for configuring the objective functions. The link is achieved by matching the flow information between both CFD codes in an iterative procedure. Compared to an individual 3D-CFD calculation, the convergence does not take significantly longer. The potential of the linked CFD-solver is demonstrated in a multi-objective optimization for one blade row to be optimized and one operating point at a 3-stage axial compressor with inlet guide vane. Within the optimization, the objective functions are formulated, so that the performance of the axial compressor is enhanced in addition to the improved efficiency of the 3D-cascade.

Sign in / Sign up

Export Citation Format

Share Document