Pool Boiling Heat Transfer From Plain and Microporous, Square Pin-Finned Surfaces in Saturated FC-72

2000 ◽  
Vol 122 (3) ◽  
pp. 509-516 ◽  
Author(s):  
K. N. Rainey ◽  
S. M. You
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Large Scale ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Small Scale ◽  
Surface Microstructure ◽  
Transfer Coefficients ◽  
Microporous Coating ◽  
Nucleate Boiling Heat Transfer

The present research is an experimental study of “double enhancement” behavior in pool boiling from heater surfaces simulating microelectronic devices immersed in saturated FC-72 at atmospheric pressure. The term “double enhancement” refers to the combination of two different enhancement techniques: a large-scale area enhancement (square pin fin array) and a small-scale surface enhancement (microporous coating). Fin lengths were varied from 0 (flat surface) to 8 mm. Effects of this double enhancement technique on critical heat flux (CHF) and nucleate boiling heat transfer in the horizontal orientation (fins are vertical) are investigated. Results showed significant increases in nucleate boiling heat transfer coefficients with the application of the microporous coating to the heater surfaces. CHF was found to be relatively insensitive to surface microstructure for the finned surfaces except in the case of the surface with 8-mm-long fins. The nucleate boiling and CHF behavior has been found to be the result of multiple, counteracting mechanisms: surface area enhancement, fin efficiency, surface microstructure (active nucleation site density), vapor bubble departure resistance, and re-wetting liquid flow resistance. [S0022-1481(00)02603-7]

Pool Boiling Heat Transfer From Plain and Microporous, Square Pin Finned Surfaces in Saturated FC-72

1999 ◽  
Author(s):  
K. N. Rainey ◽  
S. M. You
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Large Scale ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Small Scale ◽  
Surface Microstructure ◽  
Transfer Coefficients ◽  
Microporous Coating ◽  
Nucleate Boiling Heat Transfer

Abstract The present research is an experimental study of “double enhancement” behavior in pool boiling from heater surfaces simulating microelectronic devices immersed in saturated FC-72 at atmospheric pressure. The term “double enhancement” refers to the combination of two different enhancement techniques: a large-scale area enhancement (square pin fin array) and a small-scale surface enhancement (microporous coating). Fin lengths were varied from 0 (flat surface) to 8 mm. Effects of this double enhancement technique on critical heat flux (CHF) and nucleate boiling heat transfer in the horizontal orientation (fins are vertical) are investigated. Results showed significant increases in nucleate boiling heat transfer coefficients with the application of the microporous coating to the heater surfaces. CHF was found to be relatively insensitive to surface microstructure for the finned surfaces except in the case of the surface with 8 mm long fins. The nucleate boiling and CHF behavior has been found to be the result of multiple, counteracting mechanisms: surface area enhancement, fin efficiency, surface microstructure (active nucleation site density), vapor bubble departure resistance, and re-wetting liquid flow resistance.

Microporous Coatings to Maximize Pool Boiling Heat Transfer of Saturated R-123 and Water

2015 ◽  
Vol 137 (8) ◽  
Author(s):  
Joo Han Kim ◽  
Ajay Gurung ◽  
Miguel Amaya ◽  
Sang Muk Kwark ◽  
Seung M. You
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Transfer Coefficients ◽  
Maximum Heat ◽  
Microporous Coating ◽  
Plain Surface ◽  
Improved Performance

The present research is an experimental study for the enhancement of boiling heat transfer using microporous coatings. Two types of coatings are investigated: one that is bonded using epoxy and the other by soldering. Effects on pool boiling performance were investigated, of different metal particle sizes of the epoxy-based coating, on R-123 refrigerants, and on water. All boiling tests were performed with 1 cm × 1 cm test heaters in the horizontal, upward-facing orientation in saturated conditions at atmospheric pressure and under increasing heat flux. The surface enhanced by the epoxy-based microporous coatings significantly augmented both nucleate boiling heat transfer coefficients and critical heat flux (CHF) of R-123 relative to those of a plain surface. However, for water, with the same microporous coating, boiling performance did not improve as much, and thermal resistance of the epoxy component limited the maximum heat flux that could be applied. Therefore, for water, to seek improved performance, the solder-based microporous coating was applied. This thermally conductive microporous coating, TCMC, greatly enhanced the boiling performance of water relative to the plain surface, increasing the heat transfer coefficient up to ∼5.6 times, and doubling the CHF.

Optimization of Microporous Structures in Enhancing Pool Boiling Heat Transfer of Saturated R-123, FC-72 and Water

2007 ◽  
Author(s):  
Joo H. Kim ◽  
Madhav R. Kashinath ◽  
Sang M. Kwark ◽  
Seung M. You
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Particle Sizes ◽  
Microporous Coating ◽  
Nucleate Boiling Heat Transfer ◽  
Boiling Heat Transfer Coefficient ◽  
Enhanced Surface

The present research is an experimental study for the enhancement of boiling heat transfer using microporous coating techniques. The effects of different metal particle sizes in the coating compound for microporous coatings on pool boiling performance of refrigerants and water are investigated. All boiling tests were performed with 1×1cm2 test heaters in the horizontal, upward-facing orientation under increasing heat flux conditions at atmospheric pressure in saturated R-123, FC-72, and water. Results showed that the enhanced surface by microporous coating technique significantly augmented both nucleate boiling heat transfer coefficient and critical heat flux of FC-72 and R-123 over a plain surface. However, the enhancement of boiling performance for water was comparatively insignificant compared to the other liquids.

Pool Boiling Heat Transfer with Nanotube Arrays Surface on Titanium

2012 ◽  
Vol 550-553 ◽  
pp. 2913-2916 ◽  
Author(s):  
Jin Liang Tao ◽  
Xin Liang Wang ◽  
Pei Hua Shi ◽  
Xiao Ping Shi
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Heat Transfer Performance ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Test Fluid ◽  
Porous Coating ◽  
Pool Boiling Heat Transfer ◽  
Nucleate Boiling Heat Transfer ◽  
Boiling Heat Transfer Coefficient

In this paper, a new porous coating was formed directly on the surface of titanium metal via anodic oxidation. And by the SEM, the morphology of the coating, which is composed of well-ordered perpendicular nanotubes, was characterized. Moreover, taking deionized water as the test fluid, a visualization study of the coating on its pool boiling heat transfer performance was made. The results demonstrated that compared with the smooth surface, the nucleate boiling heat transfer coefficient can increase 3 times while the nucleate boiling super heat was reduced 30%.

Boiling Heat Transfer and Critical Heat Flux Enhancement of Upward- and Downward-Facing Heater in Nanofluids

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
Muhamad Zuhairi Sulaiman ◽  
Masahiro Takamura ◽  
Kazuki Nakahashi ◽  
Tomio Okawa
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Flux Enhancement ◽  
Optimum Configuration ◽  
Wall Superheat ◽  
Nucleate Boiling Heat Transfer

Boiling heat transfer (BHT) and critical heat flux (CHF) performance were experimentally studied for saturated pool boiling of water-based nanofluids. In present experimental works, copper heaters of 20 mm diameter with titanium-oxide (TiO2) nanocoated surface were produced in pool boiling of nanofluid. Experiments were performed in both upward and downward facing nanofluid coated heater surface. TiO2 nanoparticle was used with concentration ranging from 0.004 until 0.4 kg/m3 and boiling time of tb = 1, 3, 10, 20, 40, and 60 mins. Distilled water was used to observed BHT and CHF performance of different nanofluids boiling time and concentration configurations. Nucleate boiling heat transfer observed to deteriorate in upward facing heater, however; in contrast effect of enhancement for downward. Maximum enhancements of CHF for upward- and downward-facing heater are 2.1 and 1.9 times, respectively. Reduction of mean contact angle demonstrate enhancement on the critical heat flux for both upward-facing and downward-facing heater configuration. However, nucleate boiling heat transfer shows inconsistency in similar concentration with sequence of boiling time. For both downward- and upward-facing nanocoated heater's BHT and CHF, the optimum configuration denotes by C = 400 kg/m3 with tb = 1 min which shows the best increment of boiling curve trend with lowest wall superheat ΔT = 25 K and critical heat flux enhancement of 2.02 times.

Experimental Study of Surfactant Effects on Pool Boiling Heat Transfer

1990 ◽  
Vol 112 (1) ◽  
pp. 207-212 ◽  
Author(s):  
Ying Liang Tzan ◽  
Yu Min Yang
Keyword(s):  
Heat Transfer ◽  
Binary Mixtures ◽  
Boiling Heat Transfer ◽  
Sodium Lauryl Sulfate ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Additive Concentration ◽  
Lauryl Sulfate ◽  
Diffusion Effect ◽  
Nucleate Boiling Heat Transfer

In the first part of this work, nucleate boiling of aqueous solutions of sodium lauryl sulfate (SLS) over relatively wide ranges of concentration and heat flux was carried out in a pool boiling apparatus. The experimental results show that a small amount of surface active additive makes the nucleate boiling heat transfer coefficient h considerably higher, and that there is an optimum additive concentration for higher heat fluxes. Beyond this optimum point, further increase in additive concentration makes h lower. In the second part of this work, nucleate boiling heat transfer rate for n-propanol-water binary mixtures with various amounts of sodium lauryl sulfate were measured in the same pool boiling apparatus. The importance of the mass diffusion effect, which is caused by preferential evaporation of the more volatile component at the vapor-liquid interface on the boiling of the binary mixture, has been confirmed. However, it is shown that the effect exerted by the addition of a surfactant dominates over the mass diffusion effect in dilute binary mixtures.

scholarly journals Discussion of the Heat Flux Calculation Method During Pool Boiling on Meshed Heaters

2020 ◽  
Vol 2 (1) ◽  
pp. 247-252
Author(s):  
Łukasz J. Orman ◽  
Norbert Radek ◽  
Jacek Pietraszek ◽  
Dariusz Gontarski
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Distilled Water ◽  
Determination Method ◽  
Nucleate Boiling Heat Transfer ◽  
Calculation Results ◽  
Very High

AbstractThe paper discusses nucleate boiling heat transfer on meshed surfaces during pool boiling of distilled water and ethyl alcohol of very high purity. It presents a correlation for heat flux developed for heaters covered with microstructural coatings made of meshes. The experimental results have been compared with the calculation results performed using the correlation and have been followed by discussion. Conclusions regarding the heat flux determination method have been drawn with the particular focus on the usefulness of the considered model for heat flux calculations on samples with sintered mesh layers.

Sign in / Sign up

Export Citation Format

Share Document