scholarly journals Mechanics of Machining With Chamfered Tools

1999 ◽  
Vol 122 (4) ◽  
pp. 650-659 ◽  
Author(s):  
H. Ren ◽  
Y. Altintas
Keyword(s):  
Strain Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Orthogonal Cutting ◽  
Minimum Energy ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Conditions ◽  
Tool Geometry ◽  
Analytic Model

Chamfered cutting tools are used in high speed machining of hardened steels due to their wedge strength. An analytic model is proposed to investigate the influence of chamfer angle and cutting conditions on the cutting forces and temperature. The model is based on the tool geometry, cutting conditions, steady state temperature in the shear and chip-rake face contact zones, strain, strain rate, and the corresponding flow stress of the work material. With the aid of a slip line field model, the cutting and friction energy in the primary, secondary and chamfer zones are evaluated. By applying the minimum energy principle to total energy, the shear angle in the primary deformation zone is estimated. The corresponding shear strain, strain rate and flow stresses are identified. The model leads to the prediction of cutting forces and temperature produced in three deformation zones. The model is experimentally verified by high-speed orthogonal cutting tests applied to P20 mold steel using ISO S10 carbide and CBN cutting tools. It is shown that the analytic model is quite useful in selecting optimal chamfer angle and cutting speed which gives the minimum tool wear and relatively lower cutting forces. [S1087-1357(00)00204-5]

Observations on the Angle Relationships in Metal Cutting

1959 ◽  
Vol 81 (3) ◽  
pp. 263-279 ◽  
Author(s):  
D. M. Eggleston ◽  
R. Herzog ◽  
E. G. Thomsen
Keyword(s):  
High Speed ◽  
Metal Cutting ◽  
Orthogonal Cutting ◽  
Minimum Energy ◽  
Cutting Tools ◽  
Cutting Speed ◽  
High Speed Steel ◽  
Shear Plane ◽  
Energy Criterion ◽  
The Hill

Orthogonal-cutting experiments using SAE 1112 free-cutting steel, 2024-T4 and 6061-T6 aluminum alloys, and alpha-brass (85 Cu-15 Zn) at feeds of 0.002 to 0.010 ipr, were performed on a lathe with 18-4-1 high-speed-steel cutting tools. The mean cutting speeds and rake angles for SAE 1112 varied from 33.7 to 170.8 fpm and 5 to 40 deg, respectively, while the remainder of the alloys were tested at conditions yielding a continuous chip without a built-up edge at speeds ranging from approximately 470 to 790 fpm. It was found that the angle λ between the shear plane and the resultant tool force R was only approximately constant for each test condition and varied with cutting speed. Hence the equation λ = ϕ + β − α = const and the linear relationship between ϕ and β − α are only approximately satisfied. Furthermore, neither the Ernst and Merchant minimum-energy criterion, nor the Lee and Shaffer nor the Hill ideal plastic-solid solution, is in agreement with all the experimental observations.

A machining theory for predicting chip geometry, cutting forces etc. from work material properties and cutting conditions

1980 ◽  
Vol 371 (1747) ◽  
pp. 569-587 ◽  
Keyword(s):  
Cutting Forces ◽  
High Speed ◽  
Cutting Speed ◽  
Carbon Steels ◽  
Cutting Conditions ◽  
Strain Rates ◽  
Compression Tests ◽  
Rate Dependent ◽  
Work Material ◽  
Flow Stress Data

An approximate machining theory is described in which account is taken of the temperature and strain-rate dependent properties of the work material. A feature of the theory is that the strain rates in the zones of intense plastic deformation in which the chip is formed and along the tool/ chip interface are determined as part of the solution. The theory is applied to make predictions for two plain carbon steels and a range of cutting conditions by using flow stress data obtained from high speed compression tests and excellent agreement is shown, for example, between predicted and experimental cutting forces. The values of tool/chip interface plastic zone thickness predicted by assuming a minimum work criterion are shown to agree well with experimental values, both experiment and theory indicating a marked decrease in thickness with increase in cutting speed. It is also shown how the temperatures and strain rates in this zone can be used to determine the conditions that cause a built-up edge to be formed on the cutting tool and good agreement is again shown with experimental results.

Analytical and Thermal Modeling of High-Speed Machining With Chamfered Tools

2007 ◽  
Vol 130 (1) ◽  
Author(s):  
Yiğit Karpat ◽  
Tuğrul Özel
Keyword(s):  
Heat Generation ◽  
High Speed ◽  
Thermal Modeling ◽  
Orthogonal Cutting ◽  
Cutting Conditions ◽  
Tool Geometry ◽  
High Speed Machining ◽  
Temperature Distributions ◽  
Dead Metal Zone ◽  
Chamfered Tools

High-speed machining offers several advantages such as increased flexibility and productivity for discrete-part manufacturing. However, excessive heat generation and resulting high temperatures on the tool and workpiece surfaces in high-speed machining leads to a shorter tool life and poor part quality, especially if the tool edge geometry and cutting conditions were not selected properly. In this study, analytical and thermal modeling of high-speed machining with chamfered tools in the presence of dead metal zone has been presented to investigate the effects of cutting conditions, heat generation, and resultant temperature distributions at the tool and in the workpiece. An analytical slip-line field model is utilized to investigate the process mechanics and friction at the tool-chip and tool-workpiece interfaces in the presence of the dead metal zone in machining with a negative rake chamfered polycrystalline cubic boron nitride tool. In order to identify friction conditions, a set of orthogonal cutting tests is performed on AISI 4340 steel and chip geometries and cutting forces are measured. Thermal modeling of machining with chamfered tools based on moving band heat source theory, which utilizes the identified friction conditions and stress distributions on the tool-chip and tool-workpiece interfaces, is also formulated and temperature distributions at the tool, cutting zone, and in the workpiece are obtained. These temperature distributions are compared with the results obtained from finite element simulations. The comparison of temperature fields indicates that the proposed model provides reasonable solutions to understand the mechanics of machining with chamfered tools. Models presented here can be further utilized to optimize the tool geometry and cutting conditions for increasing benefits that high-speed machining offers.

Finite Element Simulation of Cutting Forces in Orthogonal Machining of Titanium Alloy Ti-6Al-4V

2014 ◽  
Vol 474 ◽  
pp. 192-199 ◽  
Author(s):  
Ladislav Kandráč ◽  
Ildikó Maňková ◽  
Marek Vrabel' ◽  
Jozef Beňo
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Cutting Forces ◽  
Orthogonal Cutting ◽  
Experimental Studies ◽  
Cutting Speed ◽  
Rake Angle ◽  
Simulation Software ◽  
Tool Geometry ◽  
Element Method

In this paper, a Lagrangian finite element-based machining model is applied in the simulation of cutting forces in two-dimensional orthogonal cutting of titanium Ti-6Al-4V alloy. The simulations were conducted using 2D Finite Element Method (FEM) machining simulation software. In addition, the cutting experiments were carried out under the different cutting speed, feed and tool geometry (rake angle, clearance angle and cutting edge radius). The effect of cutting speed, feed and tool geometry on cutting force were investigated. The results obtained from the finite element method (FEM) and experimental studies were compared.

Experimental and FEM Study of Serrated Chip Formation in High Speed Turning Processes

2011 ◽  
Vol 264-265 ◽  
pp. 1021-1026
Author(s):  
U. Umer ◽  
Li Jing Xie ◽  
Syed Jawid Askari ◽  
S.N. Danish ◽  
S.I. Butt
Keyword(s):  
Chip Formation ◽  
Cutting Forces ◽  
High Speed ◽  
Metal Cutting ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Chip Morphology ◽  
Serrated Chip ◽  
High Speed Turning ◽  
Serrated Chip Formation

The finite element method (FEM) has been used to model high speed turning processes with orthogonal cutting conditions. In most of the situations, continuous chip formation is used to analyze the turning process due to its stability and allowing many conditions to simplify the process. However with the increasing applications of high speed turning, serrated chip formation is becoming a more common phenomenon in metal cutting. Serrated chips usually occur in machining of difficult to cut materials at or above a threshold speed. An updated Lagrangian formulation has been used in this study which works with element deletion technique based on a failure criterion. The Johnson Cook strain-hardening thermal-softening material model is used to model serrated chip formation. In addition high speed turning experiments were conducted on AISI H13 tubes using PCBN to analyze serrated chip phenomenon. The chips were analyzed after surface treatment using scanning electron microscope. It has been found that the length of cuts in the chip increases with the cutting speed and the chip changes from serrated to discontinuous. Different process variables like cutting forces, chip morphology, stress, strain and temperature distributions are predicted at different process parameters using FEM. The results show cyclic variation in the cutting forces at high cutting speeds due to varying chip load.

Experimental and Numerical Investigation into Residual Stress During Turning Operation for Stainless Steel AISI 316

2020 ◽  
Vol 38 (12A) ◽  
pp. 1862-1870
Author(s):  
Safa M. Lafta ◽  
Maan A. Tawfiq
Keyword(s):  
Stainless Steel ◽  
Residual Stresses ◽  
Orthogonal Cutting ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Percentage Error ◽  
Depth Of Cut ◽  
Main Role ◽  
Turning Operation ◽  
Aisi 316

RS (residual stresses) represent the main role in the performance of structures and machined parts. The main objective of this paper is to investigate the effect of feed rate with constant cutting speed and depth of cut on residual stresses in orthogonal cutting, using Tungsten carbide cutting tools when machining AISI 316 in turning operation. AISI 316 stainless steel was selected in experiments since it is used in many important industries such as chemical, petrochemical industries, power generation, electrical engineering, food and beverage industry. Four feed rates were selected (0.228, 0.16, 0.08 and 0.065) mm/rev when cutting speed is constant 71 mm/min and depth of cutting 2 mm. The experimental results of residual stresses were (-15.75, 12.84, 64.9, 37.74) MPa and the numerical results of residual stresses were (-15, 12, 59, and 37) MPa. The best value of residual stresses is (-15.75 and -15) MPa when it is in a compressive way. The results showed that the percentage error between numerical by using (ABAQUS/ CAE ver. 2017) and experimental work measured by X-ray diffraction is range (2-15) %.

Effects of Cooling Conditions on Thermal Crack Initiation of Brittle Cutting Tools during Intermittent Cutting

2015 ◽  
Vol 656-657 ◽  
pp. 237-242
Author(s):  
Kenji Yamaguchi ◽  
Tsuyoshi Fujita ◽  
Yasuo Kondo ◽  
Satoshi Sakamoto ◽  
Mitsugu Yamaguchi ◽  
...  
Keyword(s):  
Crack Initiation ◽  
Thermal Shock ◽  
High Speed ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Condition ◽  
Thermal Crack ◽  
Cooling Conditions ◽  
Cutting Operation ◽  
Intermittent Cutting

It is well known that a series of cracks running perpendicular to the cutting edge are sometimes formed on the rake face of brittle cutting tools during intermittent cutting. The cutting tool is exposed to elevated temperatures during the periods of cutting and is cooled quickly during noncutting times. It has been suggested that repeated thermal shocks to the tool during intermittent cutting generate thermal fatigue and result in the observed thermal cracks. Recently, a high speed machining technique has attracted attention. The tool temperature during the period of cutting corresponds to the cutting speed. In addition, the cooling and lubricating conditions affect the tool temperature during noncutting times. The thermal shock applied to the tool increases with increasing cutting speed and cooling conditions. Therefore, to achieve high-speed cutting, the evaluation of the thermal shock and thermal crack resistance of the cutting tool is important. In this study, as a basis for improving the thermal shock resistance of brittle cutting tools during high-speed intermittent cutting from the viewpoint of cutting conditions, we focused on the cooling conditions of the cutting operation. An experimental study was conducted to examine the effects of noncutting time on thermal crack initiation. Thermal crack initiation was found to be restrained by reducing the noncutting time. In the turning experiments, when the noncutting time was less than 10 ms, thermal crack initiation was remarkably decreased even for a cutting speed of 500 m/min. In the milling operation, the number of cutting cycles before thermal crack initiation decreased with increasing cutting speed under conditions where the cutting speed was less than 500 m/min. However, when the cutting speed was greater than 600 m/min, thermal crack initiation was restrained. We applied the minimal quantity lubrication (MQL) coolant supply to the intermittent cutting operation. The experimental results showed that the MQL diminished tool wear compared with that under the dry cutting condition and inhibited thermal crack initiation compared with that under the wet cutting condition.

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

The Application of FEA in High-Speed Cutting

2011 ◽  
Vol 287-290 ◽  
pp. 104-107
Author(s):  
Lian Qing Ji ◽  
Kun Liu
Keyword(s):  
High Speed ◽  
Feeding Rate ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Material Model ◽  
Friction Model ◽  
Cutting Depth ◽  
High Speed Cutting ◽  
Key Technologies

The history and application of the FEA are briefly presented in this paper. Several key technologies such as the building of material model, the establishment of the chip - tool friction model as well as meshing are described. Taking the high-speed cutting of titanium alloy (Ti - 10V - 2Fe - 3Al) as an example , reasonable cutting tools and cutting parameters are determinted by simulating the influences of cutting speed, cutting depth and feeding rate on the cutting parameters using FEA.

Development of Tooling Cost Model for High Speed Hard Turning

2011 ◽  
Vol 418-420 ◽  
pp. 1482-1485 ◽  
Author(s):  
Erry Yulian Triblas Adesta ◽  
Muataz Al Hazza ◽  
Delvis Agusman ◽  
Agus Geter Edy Sutjipto
Keyword(s):  
Feed Rate ◽  
High Speed ◽  
Hard Turning ◽  
Cost Model ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Rake Angle ◽  
Depth Of Cut ◽  
Predictive Regression ◽  
Aisi 4340

The current work presents the development of cost model for tooling during high speed hard turning of AISI 4340 hardened steel using regression analysis. A set of experimental data using ceramic cutting tools, composed approximately of Al2O3 (70%) and TiC (30%) on AISI 4340 heat treated to a hardness of 60 HRC was obtained in the following design boundary: cutting speeds (175-325 m/min), feed rate (0.075-0.125 m/rev), negative rake angle (0 to -12) and depth of cut of (0.1-0.15) mm. The output data is used to develop a new model in predicting the tooling cost using in terms of cutting speed, feed rate, depth of cut and rake angle. Box Behnken Design was used in developing the model. Predictive regression model was found to be capable of good predictions the tooling cost within the boundary design.

Sign in / Sign up

Export Citation Format

Share Document