Microtexture Dependence of Mechanical and Electrical Properties of Gold Thin Films Used for Micro Bumps of 3D Stacking Structures

2021 ◽  
Author(s):  
Genta Nakauchi ◽  
Shota Akasaki ◽  
Hideo Miura
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Mechanical And Electrical Properties ◽  
Gold Thin Films ◽  
3D Stacking

Microtexture Dependence of Mechanical and Electrical Properties of Gold Thin Films Used for Micro Bumps of 3D Stacking Structures

2020 ◽  
Author(s):  
Genta Nakauchi ◽  
Shota Akasaki ◽  
Hideo Miura
Keyword(s):  
Thin Films ◽  
Mechanical Properties ◽  
Electrical Properties ◽  
Grain Boundaries ◽  
Indentation Test ◽  
Electron Back Scatter Diffraction ◽  
Effective Lifetime ◽  
Mechanical And Electrical Properties ◽  
Gold Thin Films ◽  
3D Stacking

Abstract The variation of their crystallinity, in other words, the order of atom arrangement of grain boundaries in electroplated gold thin films was investigated by changing their manufacturing conditions. Then, the effect of the crystallinity on both their mechanical and electrical properties was measured by using nano-indentation test and electromigration test. The crystallinity of the gold thin films was varied by changing the under-layer material used for electroplating. Also, the micro texture of gold thin films was evaluated by EBSD (Electron Back-Scatter Diffraction) and XRD (X-Ray Diffraction). It was clarified that the crystallinity of the electroplated gold thin films changed drastically depending on the crystallinity of the under-layer materials and electroplating conditions such as current density and temperature. This variation of the crystallinity should have caused wide variation of mechanical properties of the films. In addition, their mechanical properties such as Young’s modulus and hardness showed wide variation by about 3 times comparing with those of bulk gold. Similarly, the EM resistance of the electroplated gold bumps varied drastically depending on the ratio of porous grain boundaries and their crystallinity. Both the ratio and crystallinity also varied depending on the crystallinity of the under layer and electroplating conditions. The effective lifetime of the gold bumps was successfully predicted by considering both the crystallinity and residual stress of fine gold bumps. The lifetime varied more than 10 times as a strong function of the crystallinity of grain boundaries in the fine bumps. Therefore, it is very important to control the crystallinity of the under-layer for electroplating in order to control the distribution of the mechanical properties and reliability of the electroplated gold thin films.

scholarly journals Influence of nitrogen content on the structural, mechanical and electrical properties of TiN thin films

2005 ◽  
Vol 191 (2-3) ◽  
pp. 317-323 ◽  
Author(s):  
F. Vaz ◽  
J. Ferreira ◽  
E. Ribeiro ◽  
L. Rebouta ◽  
S. Lanceros-Méndez ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Nitrogen Content ◽  
Mechanical And Electrical Properties ◽  
Tin Thin Films

Micro Texture Dependence of Both the Mechanical and Electrical Properties of Electroplated Copper Thin Films Used for Interconnection

2010 ◽  
Author(s):  
Naokazu Murata ◽  
Naoki Saito ◽  
Kinji Tamakawa ◽  
Ken Suzuki ◽  
Hideo Miura
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Electrical Properties ◽  
Grain Boundaries ◽  
Fracture Mode ◽  
The Other ◽  
Copper Films ◽  
Mechanical And Electrical Properties ◽  
Electroplated Copper

Both mechanical and electrical properties of electroplated copper thin films were investigated experimentally with respect to changes in their micro texture. Clear recrystallization was observed after the annealing even at low temperature of about 150°C. The fracture strain of the film annealed at 400°C increased from the initial value of about 3% to 15%, and at the same time, the yield stress of the annealed film decreased from about 270 MPa to 90 MPa. In addition, it was found that there were two fatigue fracture modes in the film annealed at the temperatures lower than 200°C. One was a typical ductile fracture mode with plastic deformation and the other was brittle one. When the brittle fracture occurred, the crack propagated along weak or porous grain boundaries which remained in the film after electroplating. The brittle fracture mode disappeared after the annealing at 400°C. These results clearly indicated that the mechanical properties of electroplated copper thin films vary drastically depending on their micro texture. Next, the electrical reliability of electroplated copper thin film interconnections was discussed. The interconnections used for electromigration (EM) tests were made by damascene process. The width of the interconnections was varied from 1 μm to 10 μm. An abrupt fracture mode due to local fusion appeared in the as-electroplated films within a few hours during the test. Since the fracture rate increased linearly with the increase of square of the applied current density, this fracture mode was dominated by local Joule heating. It seemed that the local resistance of the film increased due to the porous grain boundaries and thus, the local temperature around the porous grain boundaries increased drastically. On the other hand, the life of the interconnections annealed at 400°C was improved significantly. This was because of the increase of the average grain size and the improvement of the quality of grain boundaries in the annealed films. The electrical properties of the electroplated copper films were also dominated by their micro texture. However, the stress migration occurred in the interconnections after the annealing at 400°C. This was because of the high residual tensile stress caused by the constraint of the densification of the films by the surrounding oxide film in the interconnection structures during the annealing. Finally, electroplating condition was controlled to improve the electrical properties. Both the resistance of electromigration and electrical resistivity were improved significantly. However, electromigration of copper atoms still occurred at the interface between the electroplated copper and the thin tantalum (Ta) layer sputtered as base material. Therefore, it is very important to control the crystallographic quality of electroplated copper films and the interface between different materials for improving the reliability of thin film interconnections.

Sign in / Sign up

Export Citation Format

Share Document