scholarly journals Experimental and Numerical Study of Laminar-Turbulent Transition on a Low-Pressure Turbine Outlet Guide Vane

2021 ◽  
Author(s):  
Isak Jonsson ◽  
Srikanth Deshpande ◽  
Valery Chernoray ◽  
Oskar Thulin ◽  
Jonas Larsson
Keyword(s):  
Numerical Study ◽  
Guide Vane ◽  
Low Pressure ◽  
Low Pressure Turbine ◽  
Turbulent Transition ◽  
Laminar Turbulent Transition

scholarly journals Experimental and Numerical Study of Laminar-Turbulent Transition on a Low-Pressure Turbine Outlet Guide Vane

2020 ◽  
Author(s):  
Isak Jonsson ◽  
Srikanth Deshpande ◽  
Valery Chernoray ◽  
Oskar Thulin ◽  
Jonas Larsson
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Numerical Study ◽  
Low Pressure ◽  
Boundary Layer Transition ◽  
Ir Thermography ◽  
Low Pressure Turbine ◽  
Turbulent Transition ◽  
Transition Location ◽  
Laminar Turbulent Transition

Abstract This work presents an experimental and numerical investigation on the laminar-turbulent transition and secondary flow structures in a Turbine Rear Structure (TRS). The study was executed at engine representative Reynolds number and inlet conditions at three different turbine load cases. Experiments were performed in an annular rotating rig with a shrouded low-pressure turbine upstream of a TRS test section. The numerical results were obtained using the SST k–ω turbulence model and the Langtry-Menter γ–θ transition model. The boundary layer transition location at the entire vane suction side is investigated. The location of the onset and the transition length are measured using IR-thermography along the entire vane span. The IR-thermography approach was validated using hot-wire boundary layer measurements. Both experiments and CFD show large variations of transition location along the vane span with strong influences from endwalls and turbine outlet conditions. Both correlate well with traditional transition onset correlations near midspan and show that the transition onset Reynolds number is independent of the acceleration parameter. However, CFD tends to predict an early transition onset in the midspan vane region and a late transition in the hub region. Furthermore, in the hub region, CFD is shown to overpredict the transverse flow and related losses.

scholarly journals Experimental and Numerical Study of Laminar-Turbulent Transition on a Low-Pressure Turbine Outlet Guide Vane

2021 ◽  
pp. 1-29
Author(s):  
Isak Jonsson ◽  
Srikanth Deshpande ◽  
Valery Chernoray ◽  
Oskar Thulin ◽  
Jonas Larsson
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Numerical Study ◽  
Low Pressure ◽  
Boundary Layer Transition ◽  
Ir Thermography ◽  
Low Pressure Turbine ◽  
Turbulent Transition ◽  
Transition Location ◽  
Laminar Turbulent Transition

Abstract This work presents an experimental and numerical investigation on the laminar-turbulent transition and secondary flow structures in a Turbine Rear Structure (TRS). The study was executed at engine representative Reynolds number and inlet conditions at three different turbine load cases. Experiments were performed in an annular rotating rig with a shrouded low-pressure turbine upstream of a TRS test section. The numerical results were obtained using the SST k–ω turbulence model and the Langtry- Menter γ–θ transition model. The boundary layer transition location at the entire vane suction side is investigated. The location of the onset and the transition length are measured using IR thermography along the entire vane span. The IR-thermography approach was validated using hot-wire boundary layer measurements. Both experiments and CFD show large variations of transition location along the vane span with strong influences from endwalls and turbine outlet conditions. Both correlate well with traditional transition onset correlations near midspan and show that the transition onset Reynolds number is independent of the acceleration parameter. However, CFD tends to predict an early transition onset in the midspan vane region and a late transition in the hub region. Furthermore, in the hub region, CFD is shown to overpredict the transverse flow and related losses.

Prediction of Lapse Rate in Low Pressure Turbines With and Without Modeling of the Laminar-Turbulent Transition

2007 ◽  
Author(s):  
Mahmoud L. Mansour ◽  
S. Murthy Konan ◽  
Shraman Goswami
Keyword(s):  
Reynolds Number ◽  
Turbulence Model ◽  
Test Data ◽  
Low Pressure ◽  
Lapse Rate ◽  
Test Cases ◽  
Low Pressure Turbine ◽  
Turbulent Transition ◽  
Transition Modeling ◽  
Laminar Turbulent Transition

Although turbo-machinery main stream flows are predominantly turbulent, the low pressure turbine airfoil surface boundary layer may be either laminar or turbulent. When boundary layer flow is laminar and passes through a zone of adverse pressure gradient, bypass or separation transition can occur via the Tollmien-Schlichting or Kelvin-Helmholtz instabilities. As the gas turbine’s low pressure turbine operating condition changes from sea level take-off to the altitude cruise, Reynolds number is significantly lowered and the turbine’s performance loss increases significantly. This fall-off in performance characteristic is known as lapse rate. Ability to accurately model such phenomenon is a prerequisite for reliable loss prediction and essential for improving low pressure turbine designs. Establishing such capability requires the validation and evaluation of existing low Reynolds number turbulence models, with laminar-turbulent transition modeling capability, against test cases with measured data. This paper summarizes the results of evaluating and validating two 3D viscous “RANS” Reynolds-Averaged Navier-Stokes programs for two test cases with test data. The first test case is the ERCOFTAC’ flat plate with and without pressure gradient, and the second is a Honeywell three-and-half-stage low pressure turbine with available test data at high and low Reynolds number operations. In addition to evaluating the CFD codes against test data, the flat plate test cases were used to establish the meshing and modeling best practice for each code before performing the validation for the Honeywell multistage low pressure turbine. The RANS CFD programs are Numeca’s Fine Turbo and ANSYS/CFX. Numeca’s Fine Turbo employs a two-equation K-ε turbulence model without laminar-turbulent transition modeling capability and the one-equation Spallart-Allmaras turbulence model with laminar-turbulent transition modeling capability. The ANSYS/CFX, on the other hand, employs a two-equation K-ω turbulence model (AKA SST or shear stress transport) with ability to model laminar-turbulent transition. Predictions of the CFD codes are compared with test data and the impact of modeling the laminar-turbulent transition on the prediction accuracy is assessed and presented. Both CFD codes are commercially available and the evaluation presented here is based on users’ prospective that targets the applicability of such predictive tools in the turbine design process.

Improvement of Laminar-Turbulent Transition Modeling Within a Low-Pressure Turbine

2016 ◽  
Author(s):  
A. Minot ◽  
I. Salah El-Din ◽  
R. Barrier ◽  
J.-C. Boniface ◽  
J. Marty
Keyword(s):  
Reynolds Number ◽  
Mach Number ◽  
Separation Bubble ◽  
Suction Side ◽  
Low Pressure ◽  
Boundary Layer Transition ◽  
Flow Angle ◽  
Low Pressure Turbine ◽  
Turbulent Transition ◽  
Laminar Turbulent Transition

The flow within turbomachines is intrinsically complex and involves boundary layer transition, separation and vortices such as the tip leakage vortex and wakes. In a low-pressure turbine, as the Reynolds number can be small, the flow over the suction side is likely to separate leading to the formation of a laminar (or transitional) separation bubble. This flow mechanism can be predicted using Large-Eddy Simulation. However the computation is still very expensive in a design framework. Thus, Reynolds-Averaged Navier-Stokes (RANS) method is used in the present investigation to simulate the flow over the low-pressure turbine airfoil T106C. The laminar-turbulent transition is modeled with the γ-Rθt~ model of Menter and Langtry. Following the work of Minot et al. in which the CFD setup was deeply investigated, the present study aims at evaluating the sensitivity to uncertainties relative to experimental values (freestream turbulence, Reynolds number, incidence flow angle and exit isentropic Mach number) and at improving this model regarding the calibration of several functions using optimization process. The uncertainty study highlights the parameters which mainly influence the isentropic Mach number and loss distributions. The new calibration of the Menter-Langtry model improves significantly the flow prediction over the suction side, except for the open bubble configuration.

Aerodynamic Effects of an Unshrouded Low Pressure Turbine on a Low Aspect Ratio Exit Guide Vane

2012 ◽  
Author(s):  
Thorsten Selic ◽  
Davide Lengani ◽  
Andreas Marn ◽  
Franz Heitmeir
Keyword(s):  
Aspect Ratio ◽  
Guide Vane ◽  
Low Pressure ◽  
Tip Clearance ◽  
Pressure Probe ◽  
Model Parameters ◽  
Leakage Flow ◽  
Low Pressure Turbine ◽  
Low Aspect Ratio ◽  
The Impact

This paper presents the effects of an unshrouded low pressure turbine (LPT) onto the following exit guide vane row (EGV). The measurement results were obtained in the subsonic test turbine facility at Graz University of Technology by means of a fast response pressure probe in planes downstream of the rotor as well as oil flow visualisation. The test rig was designed in cooperation with MTU Aero Engines and represents the last 1.5 stages of a commercial aero engine. Considerable efforts were put into the adjustment of all relevant model parameters to reproduce the full scale LPT situation. Different tip clearances were evaluated by means of CFD obtained using a commercial Navier-Stokes code and validated with experimental results. The goal is to evaluate the effect of the varying leakage flow on the flow in the low aspect ratio EGV. Special attention is given to the impact on the development of secondary flows as well as the flow structures downstream of the EGV. The effect of the leakage flow causes a change of the flow structure of the EGV, particularly losses. Considering the largest investigated tip-clearance, the losses increased by 71% when compared to a zero-leakage case.

Investigation of the Impact of Unsteady Turbulence Effects on the Aeroelastic Analysis of a Low-Pressure Turbine Rotor Blade

2019 ◽  
Vol 141 (10) ◽  
Author(s):  
Jan Philipp Heners ◽  
Damian M. Vogt ◽  
Christian Frey ◽  
Graham Ashcroft
Keyword(s):  
Rotor Blade ◽  
Numerical Study ◽  
Turbulence Models ◽  
Gibbs Phenomenon ◽  
Low Pressure ◽  
Turbine Rotor ◽  
Filter Method ◽  
Turbine Rotor Blade ◽  
Low Pressure Turbine ◽  
The Impact

Abstract The impact of the unsteadiness in the considered turbulence quantities on the numerical prediction of the aeroelastic behavior of a low-pressure turbine (LPT) rotor blade is evaluated by means of a numerical study. In this context, one of the main objectives of this work is to compare different nonlinear harmonic balance (HB) approaches—one neglecting and one considering the unsteadiness in the employed turbulence models—with a conventional nonlinear solver of the unsteady Reynolds-averaged Navier–Stokes (URANS) equations in the time domain. In order to avoid unphysical oscillations in the turbulence quantities caused by the Gibbs phenomenon in the chosen HB approach, a filter method based on the Lanczos filter is developed. The developed filter method is applied in the course of the HB simulations considering the unsteadiness in the underlying turbulence model. Furthermore, the impact of its application on the solution of the flow field and on the unsteady surface pressure of the rotor blade, in particular, is discussed in the context of this work.

scholarly journals Numerical Study of Flutter Stabilization in Low Pressure Turbine Rotor with Intentional Mistuning

2018 ◽  
Vol 148 ◽  
pp. 98-105 ◽  
Author(s):  
Sara Biagiotti ◽  
Lorenzo Pinelli ◽  
Francesco Poli ◽  
Federico Vanti ◽  
Roberto Pacciani
Keyword(s):  
Numerical Study ◽  
Low Pressure ◽  
Turbine Rotor ◽  
Low Pressure Turbine
Sign in / Sign up

Export Citation Format

Share Document