Influence of Shunt Injection on Predicted Rotordynamic Coefficients of a Labyrinth Seal Using Transient CFD

2021 ◽  
Author(s):  
Manish Thorat ◽  
Jin Jin ◽  
Brian Pettinato
Keyword(s):  
Labyrinth Seal ◽  
Rotordynamic Coefficients

Rotordynamic Coefficients of Labseals for Turbines: Comparing CFD Results With Experimental Data on a Comb-Grooved Labyrinth

2005 ◽  
Author(s):  
Joachim Schettel ◽  
Martin Deckner ◽  
Klaus Kwanka ◽  
Bernd Lu¨neburg ◽  
Rainer Nordmann
Keyword(s):  
Stokes Equations ◽  
Labyrinth Seal ◽  
Navier Stokes ◽  
Test Rig ◽  
Navier Stokes Equations ◽  
Detailed Model ◽  
Identification Methods ◽  
Rotating Speed ◽  
Flow Models ◽  
Rotordynamic Coefficients

The main goal of this paper is to improve identification methods for rotordynamic coefficients of labseals for turbines. This aim was achieved in joint effort of the Technische Universita¨t Mu¨nchen, working on experimental identification methods for rotordynamic coefficients, the University of Technology, Darmstadt, working on prediction methods, and Siemens AG, realizing the results. The paper focuses on a short comb-grooved labyrinth seal. Short labseals, amongst others the above mentioned comb-grooved labyrinth, were examined. by means of a very accurately measuring test rig. The rotor was brought into statically eccentric positions relative to the stator, in order to measure the circumferential pressure distribution as a function of pressure, rotating speed and entrance swirl. The data collected were used to validate results obtained with a numerical method. The theoretical approach is based on a commercial CFD tool, which solves the Navier Stokes equations using numerical methods. As a result, a detailed model of the flow within the test rig is produced. The efforts of computation here are greater than when compared with the likewise wide-spread Bulk flow models, however improved accuracy and flexibility is expected. As the validation of the model is successful, it could then be used to gain further insight in the flow within the seal, and to understand the results better. This showed that rotordynamic coefficients of labseals gained from different test rigs are not necessarily comparable.

Impact of Frequency Dependence of Gas Labyrinth Seal Rotordynamic Coefficients on Centrifugal Compressor Stability

2010 ◽  
Author(s):  
Giuseppe Vannini ◽  
Manish R. Thorat ◽  
Dara W. Childs ◽  
Mirko Libraschi
Keyword(s):  
Molecular Weight ◽  
Numerical Model ◽  
Control Volume ◽  
Labyrinth Seal ◽  
Labyrinth Seals ◽  
Frequency Dependent ◽  
Rotordynamic Coefficients ◽  
Frequency Independent ◽  
Rotor Surface ◽  
Independent Model

A numerical model developed by Thorat & Childs [1] has indicated that the conventional frequency independent model for labyrinth seals is invalid for rotor surface velocities reaching a significant fraction of Mach 1. A theoretical one-control-volume (1CV) model based on a leakage equation that yields a reasonably good comparison with experimental results is considered in the present analysis. The numerical model yields frequency-dependent rotordynamic coefficients for the seal. Three real centrifugal compressors are analyzed to compare stability predictions with and without frequency-dependent labyrinth seal model. Three different compressor services are selected to have a comprehensive scenario in terms of pressure and molecular weight (MW). The molecular weight is very important for Mach number calculation and consequently for the frequency dependent nature of the coefficients. A hydrogen recycle application with MW around 8, a natural gas application with MW around 18, and finally a propane application with molecular weight around 44 are selected for this comparison. Useful indications on the applicability range of frequency dependent coefficients are given.

scholarly journals Annular Honeycomb Seals: Test Results for Leakage and Rotordynamic Coefficients; Comparisons to Labyrinth and Smooth Configurations

1989 ◽  
Vol 111 (2) ◽  
pp. 293-300 ◽  
Author(s):  
D. Childs ◽  
D. Elrod ◽  
K. Hale
Keyword(s):  
Labyrinth Seal ◽  
Test Results ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Stiffness Coefficients ◽  
Shaft Rotation ◽  
Honeycomb Seal ◽  
Cell Dimensions ◽  
Honeycomb Seals ◽  
Rotordynamic Coefficient

Test results are presented for leakage and rotordynamic coefficients for seven honeycomb seals. All seals have the same radius, length, and clearance; however, the cell depths and diameters are varied. Rotordynamic data, which are presented, consist of the direct and cross-coupled stiffness coefficients and the direct damping coefficients. The rotordynamic-coefficient data show a considerable sensitivity to changes in cell dimensions; however, no clear trends are identifiable. Comparisons of test data for the honeycomb seals with labyrinth and smooth annular seals shows the honeycomb seal had the best sealing (minimum leakage) performance, followed in order by the labyrinth and smooth seals. For prerotated fluids entering the seal, in the direction of shaft rotation, the honeycomb seal has the best rotordynamic stability followed in order by the labyrinth and smooth. For no prerotation, or fluid prerotation against shaft rotation, the labyrinth seal has the best rotordynamic stability followed in order by the smooth and honeycomb seals.

Effects of Increased Tooth Clearance on the Performance of a Labyrinth Seal With Oil-Rich Bubbly Laminar Flow

2021 ◽  
Author(s):  
Min Zhang ◽  
Dara W. Childs
Keyword(s):  
Smooth Surface ◽  
Volume Fraction ◽  
Silicone Oil ◽  
Bubbly Flow ◽  
Labyrinth Seal ◽  
Test Fluid ◽  
Axial Thrust ◽  
Rotordynamic Coefficients ◽  
Piston Seal ◽  
The Impact

Abstract In recent years, multiphase pumps have become more and more popular because of the capability to simplify the process, reduce the footprint, and lower the cost. To compensate for the axial thrust force, an annular seal is normally used as a balance piston seal, and the labyrinth seal is one of the choices. A typical labyrinth seal consists of a surface with teeth and a smooth surface. The teeth are either on the rotor or the stator. To protect the machine, one side (either the teeth or the smooth surface) is made of a material that can be safely sacrificed during a rub. After the rub, the teeth clearance is increased. This paper studies the impact of the increased teeth clearance on the performance of the labyrinth seal under oil-rich bubbly flow conditions. The test fluid is a mixture of silicone oil (PSF 5cSt) and air with inlet Gas Volume Fraction GVF up to 9%. Tests are conducted with pressure drop PD = 34.5 bars, rotor speed ω = 5 krpm, and radial tooth clearance Cr = 0.102 mm and 0.178 mm. Test results show that, for all test conditions (before and after injecting air bubbles into the oil flow), increasing Cr from 0.102 mm to 0.178 mm increases the mass flow rate by about 40% but barely changes the test seal’s rotordynamic coefficients; i.e., the increased tooth clearance would not change the pump vibration performance.

Segmentation Effects on Brush Seal Leakage and Rotordynamic Coefficients

2015 ◽  
Author(s):  
Alexander O. Pugachev ◽  
Manuel Gaszner ◽  
Christos Georgakis ◽  
Paul Cooper
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Labyrinth Seal ◽  
Performance Characteristics ◽  
Radial Clearance ◽  
Single Plane ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Brush Seal ◽  
Stiffness And Damping

This paper studies the effect of brush seal segmentation on the seal performance characteristics. A brush-labyrinth sealing configuration arranged of one brush seal downstream and two labyrinth fins upstream is studied experimentally and theoretically. The studied brush seal is of welded design installed with zero cold radial clearance. The brush seal front and back rings as well as the bristle pack are segmented radially in a single plane using the electrical discharge machining technique. The segmentation procedure results in loss of bristles at the site of the cuts altering the leakage flow structure in the seal and its performance characteristics. Two test rigs are used to obtain leakage, as well as rotordynamic stiffness and damping coefficients of the seal at different pressure ratios. The CFD-based model is used to predict the seal performance and to study in detail local changes in the flow field due to the segmentation. A back-to-back comparison of the performance of non-segmented and segmented brush seals, as well as baseline labyrinth seal is provided. The obtained results demonstrate that the segmentation in general negatively affects the performance of the studied brush-labyrinth sealing configuration. However, the segmented brush seal shows increased direct damping coefficients.

Numerical Comparison of Leakage Flow and Rotordynamic Characteristics for Two Types of Labyrinth Seals With Baffles

2020 ◽  
Vol 142 (9) ◽  
Author(s):  
Yuanqiao Zhang ◽  
Jun Li ◽  
Zhigang Li ◽  
Xin Yan
Keyword(s):  
Rotational Speed ◽  
Flow Resistance ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Numerical Comparison ◽  
Vibration Frequencies ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Brush Seal ◽  
Swirl Intensity

Abstract Cavity separation baffles can decrease the circumferential swirl intensity of labyrinth seals and increase the seals' rotordynamic characteristics. Compared with conventional baffles, the bristle packs of brush seal baffles can contact the rotor directly, thereby further reducing the swirl intensity of the seal cavity. This paper, using the numerical model combining a multifrequency elliptical whirling orbit model, a porous medium model, and transient Reynolds-averaged Navier–Stokes (RANS) solutions, compares the leakage flow and rotordynamic characteristics of a labyrinth seal with brush-seal baffles (LSBSB) and a labyrinth seal with conventional baffles (LSCB). Ideal air flows into the seal at an inlet preswirl velocity of 0 m/s (or 60 m/s or 100 m/s), total pressure of 690 kPa, and temperature of 14 °C. The outlet static pressure is 100 kPa and the rotational speed is 7500 r/min (surface speed of 66.8 m/s) or 15,000 r/min (surface speed of 133.5 m/s). Numerical results show that the LSBSB possesses the slightly less leakage flow rate than the LSCB due to the flow resistance of the bristle pack to the fluid. Compared with the LSCB, the LSBSB shows a higher positive effective stiffness (Keff) at all considered vibration frequencies and a higher effective damping (Ceff) for most vibration frequencies. What is more, the crossover frequency (fc0) of the LSBSB is significantly lower than that of the LSCB, which means that the LSBSB has a wider frequency range offering positive effective damping. The increasing inlet preswirl velocity and rotational speed only slightly affect the Keff for both seals. The Ceff of two seals decreases as the inlet preswirl velocity rises, especially for the LSCB. The Ceff of the LSCB slightly decreases because of the increasing rotational speed. In contrast, the Ceff of the LSBSB is not sensitive to the changes in rotational speed. In a word, the LSBSB possesses superior rotordynamic performance to the LSCB. Note that this work also investigates the leakage flow and rotordynamic characteristics a labyrinth seal with inclined baffles (LSIB) under the condition of u0 = 60 m/s and n = 15,000 r/min. The inclined baffles of the LSIB are same as the backing plates of LSBSB baffles. The LSIB has rotordynamic coefficients almost equal to the LSCB. Hence, the reason why the LSBSB possesses better rotordynamic performance than that of the LSCB is the flow resistance of bristle packs of brush seal baffles, not the inclination direction variation of baffles.

Influence of Teeth Damage on Rotordynamic Instability of Impeller Eye Seals in Centrifugal Compressors

2005 ◽  
Author(s):  
Jinxiang Xi ◽  
David L. Rhode
Keyword(s):  
Labyrinth Seal ◽  
Accurate Prediction ◽  
Centrifugal Compressors ◽  
Perturbation Model ◽  
Rotordynamic Coefficients ◽  
Leakage Path ◽  
Swirl Velocity ◽  
Inlet Swirl ◽  
Rotordynamic Forces

This paper investigates the influence of labyrinth seal teeth damage due to rotor impacting on the performance and the rotordynamic characteristics of impeller eye seals in centrifugal compressors. A well-established CFD-perturbation model was employed to predict the rotordynamic coefficients. The inclusion of at least an approximate shroud leakage path chamber is prefered for accurate prediction of seal-inlet swirl velocity and flow-induced rotordynamic forces. Impeller eye seals with teeth damage: (a) suffer significant leakage increases due to the increased seal clearance and (b) produce higher seal-inlet swirl velocity as well as larger rotordynamic forces, which tend to cause the system to become unstable. It was also found that distorted teeth tip geometries have an insignificant influence on both leakage and rotordynamic coefficients. The leakage path influence on seal-inlet swirl velocity W0 was also explored to thoroughly understand the rotordynamic characteristics of the eye seal subject to various degrees of teeth damage.

scholarly journals Rotordynamic Coefficient and Leakage Test Results for Interlock and Tooth-on-Stator Labyrinth Seals

1988 ◽  
Author(s):  
Dara W. Childs ◽  
David A. Elrod ◽  
Keith Hale
Keyword(s):  
Labyrinth Seal ◽  
Damping Coefficient ◽  
Test Results ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Leakage Test ◽  
Stiffness And Damping ◽  
Rotordynamic Coefficient

Test results (leakage and rotordynamic coefficients) are presented for an interlock and tooth-on-stator labyrinth seals. Tests were carried out with air at speeds out to 16,000 cpm and supply pressures up to 7.5 bars. The rotordynamic coefficients consist of direct and cross-coupled stiffness and damping coefficients. Damping-coefficient data have not previously been presented for interlock seals. The test results support the following conclusions: (a) The interlock seal leaks substantially less than labyrinth seals. (b) Destabilizing forces are lower for the interlock seal. (c) The labyrinth seal has substantially greater direct damping values than the interlock seal. A complete rotordynamics analysis is needed to determine which type of seal would yield the best stability predictions for a given turbomachinery unit.

Application of a Novel Rotordynamic Identification Method for Annular Seals With Arbitrary Elliptical Orbits and Eccentricities

2019 ◽  
Vol 141 (9) ◽  
Author(s):  
Wanfu Zhang ◽  
Qianlei Gu ◽  
Jiangang Yang ◽  
Chun Li
Keyword(s):  
Fluid Velocity ◽  
Reaction Force ◽  
Grid Method ◽  
Labyrinth Seal ◽  
Damping Coefficient ◽  
Eccentricity Ratio ◽  
Rotordynamic Coefficients ◽  
Identification Method ◽  
Gas Seals ◽  
Annular Seals

The identification method using infinitesimal theory is proposed to predict rotordynamic coefficients of annular gas seals. The transient solution combined with moving grid method was unitized to obtain the fluid reaction force at a specific position under different whirling frequencies. The infinitesimal method is then applied to obtain the rotordynamic coefficients, which agrees well with published experimental results for both labyrinth seals and eccentric smooth annular seals. Particularly, the stability parameter of the effective damping coefficient can be solved precisely. Results show that the whirling frequency has little influence on direct damping coefficient, effective damping coefficient, and cross-coupled stiffness coefficient for the labyrinth seal. And the effective damping coefficients decrease as the eccentricity ratio increases. A higher eccentricity ratio tends to destabilize the seal system, especially at a low whirling frequency. Results also show that the fluid velocity in the maximum clearance in the seal leakage path is less than that in the minimum clearance. The inertial effect dominates the flow field. Then it results in higher pressure appearing in maximum clearances. The pressure difference aggravates the eccentricity of rotor and results in static instabilities of the seal system.

Dynamic Response Analysis of Balance Drum Labyrinth Seal Groove Geometries Optimized for Minimum Leakage

2015 ◽  
Author(s):  
Alexandrina Untaroiu ◽  
Neal Morgan ◽  
Vahe Hayrapetian ◽  
Bruno Schiavello
Keyword(s):  
Dynamic Response ◽  
Dynamic Properties ◽  
Labyrinth Seal ◽  
Leakage Rate ◽  
Response Analysis ◽  
Test Cases ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Overall Stability ◽  
Optimization Loop

Annular labyrinth seals often have a destabilizing effect on pump rotordynamics due to the large cross-coupled forces generated when the fluid is squeezed by an oscillating rotor. In this study several novel groove geometries are investigated for their effect on the rotordynamic coefficients of the labyrinth seal. The groove cavity geometry of a baseline 267 mm balance drum labyrinth seal with a clearance of 0.305 mm and 20 equally spaced groove cavities were optimized for minimum leakage. From the pool of possible groove designs analyzed, nine test cases were selected for maximum or minimum leakage and for a variety of groove cavity shapes. The rotordynamic coefficients were calculated for these cases using a hybrid CFD-bulk flow method. The rotordynamic coefficients obtained by this method were then used with a rotordynamic model of the entire pump to determine the overall stability. Results show that labyrinth seal’s groove shape can be optimized to generate lower leakage rates, while the effects on dynamic properties are only minimally changed. If the seal dynamic response needs to be modified in addition to targeting a lower leakage rate, for instance to exhibit increased damping values, then the leakage rate and the damping coefficient need to be set as objective functions in the optimization loop.

Sign in / Sign up

Export Citation Format

Share Document