EFFECT OF LOADING RATE ON FRACTURE BEHAVIOUR OF Mg-Al-Zn ALLOYS

2016 ◽  
Vol 78 (6-9) ◽  
Author(s):  
Noradila Abdul Latif ◽  
Zainuddin Sajuri ◽  
Junaidi Syarif ◽  
Yukio Miyashita

In recent years, magnesium alloys are widely used for automotive applications as structural components due to its lightweight property and high specific strength. In this regards, magnesium alloys are subjected to high velocity and impact loads during accident. Hence, understanding the impact and dynamic behaviours of magnesium alloys are essential. In this study, the effect of loading rates on the fracture behaviour of Mg-Al-Zn alloys was investigated using pre-cracked single-edge notched bending (SENB) specimens. Three-point bending tests were conducted at different loading rates of 5, 50 and 500 mm/min. The Mg-Al-Zn alloys that used in the present study were extruded AZ31 and AZ61 magnesium alloys. From the load-load line displacement results, both alloys exhibited nonlinear fracture behaviour. The maximum load (Pmax) of these two alloys increased with increasing loading rate. Comparing both alloys, AZ61 exhibited higher Pmax than that of AZ31 due to the higher volume of b-phase and smaller grain size in AZ61. Fracture surface observation revealed that both alloys fractured in ductile manner with large scale yielding and high shear lips ratio at all loading rates.

Author(s):  
Frank Z. Liang ◽  
Larry M. Palanuk ◽  
Mike Gabriel

This paper presents two simple and unique tests to extract shock-level loading limits for eutectic and lead free solders. A wide range of loading rates, from quasi-static to high speed, was applied to a through-hole-mounted anchor assembly test coupon. The high speed shock tests were conducted on a drop shock table where the impacting velocities were derived through table input adjustments. The quasi-static tests were done using controlled hydraulic linear actuator with a load cell. As would be assumed, the dynamic load to cause solder joint failure was found to increase with higher loading rate. However, at such a high loading rate range, the impact velocity did not change the load to failure. This study leads to an interesting hypothesis that at high loading rates, the solder joint strain rate may not see a significant change as observed at low rates.


2019 ◽  
Vol 12 ◽  
pp. 1-11
Author(s):  
Gouda Mohamed Mahmoud ◽  
Khaled Mohamed

This investigation focuses on modelling the fracture zone of four materials at different test speeds. The influence of these test speeds on the fracture zone formula was investigated as well. The fracture behaviour of materials is an important parameter which greatly affects the performance of these materials. In this paper, an empirical formula was generated to predict the fracture zone. This formula was produced from experimental characterisation of the fracture process at different loading rates for some engineering materials.  Statistical analysis was done for the results being obtained from the experimental work to verify the accuracy of this formula, and it was found that it can introduce an accurate base for fracture zone prediction and determination. It was noted that at fracture process initiation, there are no significant effects of varying loading rate; this effect is increased with increasing the fracture process propagation.


2018 ◽  
Vol 58 (4) ◽  
pp. 226 ◽  
Author(s):  
Petra Hájková ◽  
Aleš Jíra ◽  
Luboš Řehounek

<p>Enamel is the hardest biological tissue in the human body because of its structure<br />and composition. The structure of interlocking rods enables this biomaterial to resist the stresses of mastication. Unfortunately, enamel is prone to fracture initiation and growth. Determining fracture toughness of enamel is a difficult task. The lack of thickness makes it impossible to prepare samples which could be analyzed by usual methods. Other authors use Vickers indentation fracture test (VIF) to determine fracture toughness of enamel ordinarily. VIF is, however, not generally acceptable.<br />The aim of this study is verification of fracture behaviour of enamel using nanoindentation. In the study the impact of changes of hardness (HIT) and reduced modulus (Er) caused by crack initiation and growth on fracture toughness determination is observed. The next goal is evaluation of loading rate impact.</p>


2017 ◽  
Author(s):  
Katherine M. Ransom ◽  
Andrew M. Bell ◽  
Quinn E. Barber ◽  
George Kourakos ◽  
Thomas Harter

Abstract. Nitrate contamination of alluvial aquifers in agricultural areas is a typical and major problem around the world. Nitrogen applied to crops, in the form of synthetic fertilizers or manure, in excess of plant uptake, largely leaches to groundwater in the form of nitrate, which is stable and highly mobile in oxygen-rich groundwaters. Increased awareness of the impact that excess nitrogen has had on groundwater and major health concerns about nitrate are prompting new regulations for farmers, e.g., in Europe and California, USA. This study is focused in the Central Valley, California, USA, an intensively farmed region with high agricultural crop diversity. Though nitrogen loading rates for several crop and landuse types in the Central Valley have been estimated or measured in a handful of studies, nitrogen loading rates for specific crop or landuse types and their impact to groundwater quality remain largely unknown. Knowledge of crop or other landuse specific groundwater nitrate impact may aid future regulatory decisions. Nitrogen loading rates for specific crop or landuse types are expected to vary depending on individual landuse practices; and interactions with hydrogeologic parameters that may promote or inhibit nitrate leaching. In this study, we developed a novel Bayesian regression model that allowed us to estimate crop or other landuse-specific groundwater nitrogen loading rate probability distributions from surveys of private wells, each of which is likely impacted by more than one landuse. We used recent nitrate measurements from 2149 wells in the Central Valley. We estimated nitrogen loading rate distributions for 15 crop and landuse groups. These were shown to compare favorably with prior mass-balance estimates of loading rates based on agronomic estimates of nitrogen loading.


2020 ◽  
Vol 59 (04) ◽  
pp. 294-299 ◽  
Author(s):  
Lutz S. Freudenberg ◽  
Ulf Dittmer ◽  
Ken Herrmann

Abstract Introduction Preparations of health systems to accommodate large number of severely ill COVID-19 patients in March/April 2020 has a significant impact on nuclear medicine departments. Materials and Methods A web-based questionnaire was designed to differentiate the impact of the pandemic on inpatient and outpatient nuclear medicine operations and on public versus private health systems, respectively. Questions were addressing the following issues: impact on nuclear medicine diagnostics and therapy, use of recommendations, personal protective equipment, and organizational adaptations. The survey was available for 6 days and closed on April 20, 2020. Results 113 complete responses were recorded. Nearly all participants (97 %) report a decline of nuclear medicine diagnostic procedures. The mean reduction in the last three weeks for PET/CT, scintigraphies of bone, myocardium, lung thyroid, sentinel lymph-node are –14.4 %, –47.2 %, –47.5 %, –40.7 %, –58.4 %, and –25.2 % respectively. Furthermore, 76 % of the participants report a reduction in therapies especially for benign thyroid disease (-41.8 %) and radiosynoviorthesis (–53.8 %) while tumor therapies remained mainly stable. 48 % of the participants report a shortage of personal protective equipment. Conclusions Nuclear medicine services are notably reduced 3 weeks after the SARS-CoV-2 pandemic reached Germany, Austria and Switzerland on a large scale. We must be aware that the current crisis will also have a significant economic impact on the healthcare system. As the survey cannot adapt to daily dynamic changes in priorities, it serves as a first snapshot requiring follow-up studies and comparisons with other countries and regions.


Author(s):  
Kulwant Singh ◽  
Gurbhinder Singh ◽  
Harmeet Singh

The weight reduction concept is most effective to reduce the emissions of greenhouse gases from vehicles, which also improves fuel efficiency. Amongst lightweight materials, magnesium alloys are attractive to the automotive sector as a structural material. Welding feasibility of magnesium alloys acts as an influential role in its usage for lightweight prospects. Friction stir welding (FSW) is an appropriate technique as compared to other welding techniques to join magnesium alloys. Field of friction stir welding is emerging in the current scenario. The friction stir welding technique has been selected to weld AZ91 magnesium alloys in the current research work. The microstructure and mechanical characteristics of the produced FSW butt joints have been investigated. Further, the influence of post welding heat treatment (at 260 °C for 1 h) on these properties has also been examined. Post welding heat treatment (PWHT) resulted in the improvement of the grain structure of weld zones which affected the mechanical performance of the joints. After heat treatment, the tensile strength and elongation of the joint increased by 12.6 % and 31.9 % respectively. It is proven that after PWHT, the microhardness of the stir zone reduced and a comparatively smoothened microhardness profile of the FSW joint obtained. No considerable variation in the location of the tensile fracture was witnessed after PWHT. The results show that the impact toughness of the weld joints further decreases after post welding heat treatment.


2020 ◽  
Vol 6 (5) ◽  
pp. 1183-1189
Author(s):  
Dr. Tridibesh Tripathy ◽  
Dr. Umakant Prusty ◽  
Dr. Chintamani Nayak ◽  
Dr. Rakesh Dwivedi ◽  
Dr. Mohini Gautam

The current article of Uttar Pradesh (UP) is about the ASHAs who are the daughters-in-law of a family that resides in the same community that they serve as the grassroots health worker since 2005 when the NRHM was introduced in the Empowered Action Group (EAG) states. UP is one such Empowered Action Group (EAG) state. The current study explores the actual responses of Recently Delivered Women (RDW) on their visits during the first month of their recent delivery. From the catchment area of each of the 250 ASHAs, two RDWs were selected who had a child in the age group of 3 to 6 months during the survey. The response profiles of the RDWs on the post- delivery first month visits are dwelled upon to evolve a picture representing the entire state of UP. The relevance of the study assumes significance as detailed data on the modalities of postnatal visits are available but not exclusively for the first month period of their recent delivery. The details of the post-delivery first month period related visits are not available even in large scale surveys like National Family Health Survey 4 done in 2015-16. The current study gives an insight in to these visits with a five-point approach i.e. type of personnel doing the visit, frequency of the visits, visits done in a particular week from among those four weeks separately for the three visits separately. The current study is basically regarding the summary of this Penta approach for the post- delivery one-month period.     The first month period after each delivery deals with 70% of the time of the postnatal period & the entire neonatal period. Therefore, it does impact the Maternal Mortality Rate & Ratio (MMR) & the Neonatal Mortality Rates (NMR) in India and especially in UP through the unsafe Maternal & Neonatal practices in the first month period after delivery. The current MM Rate of UP is 20.1 & MM Ratio is 216 whereas the MM ratio is 122 in India (SRS, 2019). The Sample Registration System (SRS) report also mentions that the Life Time Risk (LTR) of a woman in pregnancy is 0.7% which is the highest in the nation (SRS, 2019). This means it is very risky to give birth in UP in comparison to other regions in the country (SRS, 2019). This risk is at the peak in the first month period after each delivery. Similarly, the current NMR in India is 23 per 1000 livebirths (UNIGME,2018). As NMR data is not available separately for states, the national level data also hold good for the states and that’s how for the state of UP as well. These mortalities are the impact indicators and such indicators can be reduced through long drawn processes that includes effective and timely visits to RDWs especially in the first month period after delivery. This would help in making their post-natal & neonatal stage safe. This is the area of post-delivery first month visit profile detailing that the current article helps in popping out in relation to the recent delivery of the respondents.   A total of four districts of Uttar Pradesh were selected purposively for the study and the data collection was conducted in the villages of the respective districts with the help of a pre-tested structured interview schedule with both close-ended and open-ended questions.  The current article deals with five close ended questions with options, two for the type of personnel & frequency while the other three are for each of the three visits in the first month after the recent delivery of respondents. In addition, in-depth interviews were also conducted amongst the RDWs and a total 500 respondents had participated in the study.   Among the districts related to this article, the results showed that ASHA was the type of personnel who did the majority of visits in all the four districts. On the other hand, 25-40% of RDWs in all the 4 districts replied that they did not receive any visit within the first month of their recent delivery. Regarding frequency, most of the RDWs in all the 4 districts received 1-2 times visits by ASHAs.   Regarding the first visit, it was found that the ASHAs of Barabanki and Gonda visited less percentage of RDWs in the first week after delivery. Similarly, the second visit revealed that about 1.2% RDWs in Banda district could not recall about the visit. Further on the second visit, the RDWs responded that most of them in 3 districts except Gonda district did receive the second postnatal visit in 7-15 days after their recent delivery. Less than half of RDWs in Barabanki district & just more than half of RDWs in Gonda district received the third visit in 15-21 days period after delivery. For the same period, the majority of RDWs in the rest two districts responded that they had been entertained through a home visit.


e-Finanse ◽  
2018 ◽  
Vol 14 (4) ◽  
pp. 67-76
Author(s):  
Piotr Bartkiewicz

AbstractThe article presents the results of the review of the empirical literature regarding the impact of quantitative easing (QE) on emerging markets (EMs). The subject is of interest to policymakers and researchers due to the increasingly larger role of EMs in the world economy and the large-scale capital flows occurring after 2009. The review is conducted in a systematic manner and takes into consideration different methodological choices, samples and measurement issues. The paper puts the summarized results in the context of transmission channels identified in the literature. There are few distinct methodological approaches present in the literature. While there is a consensus regarding the direction of the impact of QE on EMs, its size and durability have not yet been assessed with sufficient precision. In addition, there are clear gaps in the empirical findings, not least related to relative underrepresentation of the CEE region (in particular, Poland).


Sign in / Sign up

Export Citation Format

Share Document