UPTAKE BEHAVIOR OF ARSENATE FROM AQUEOUS SOLUTION USING FERRIC-COATED MESOPOROUS CERAMIC ADSORBENT

2016 ◽  
Vol 78 (5-3) ◽  
Author(s):  
Borano Te ◽  
Boonchai Wichitsathian ◽  
Chatpet Yossapol
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Physical Adsorption ◽  
Low Cost ◽  
Ceramic Filter ◽  
Order Kinetic ◽  
Solution Ph ◽  
Batch Mode ◽  
Order Kinetic Model ◽  
Arsenate Adsorption

Broken mesoporous ceramic filter was reutilized by coating with ferric solution through a simple loading method enhanced with heating at a moderate temperature for arsenate uptake from aqueous solution. BET, XRF, XRD, and SEM methods were applied for the adsorbent characterization. The adsorption study was conducted in a batch mode to investigate kinetics, isotherms, and the effect of solution pH and co-existing anions. The pseudo-second order kinetic model well fitted the experimental data (R2 = 0.9997). The maximum arsenate adsorption capacity (2.27 mg/g) was derived from the better described Langmuir isotherm model (R2 = 0.9992). The adsorbent expressed high arsenate adsorption capacity over a pH range of 4-10. The uptake behavior is a favorable and physical adsorption process based on the value of separation factor and mean sorption energy.  The presence of co-existing anions decreased the arsenate adsorption capacity in the following order: NO3-< SO42- < PO43-. The new ferric-coated mesoporous ceramic adsorbent could be an effective and low-cost adsorbent for arsenate removal from water. 

scholarly journals Adsorption of Ni2+ from aqueous solution by magnetic Fe@graphite nano-composite

2016 ◽  
Vol 18 (4) ◽  
pp. 96-103 ◽  
Author(s):  
Wojciech Konicki ◽  
Rafał Pelka ◽  
Walerian Arabczyk
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Diffraction Method ◽  
Chemical Vapor ◽  
Bet Surface Area ◽  
Order Kinetic ◽  
Solution Ph ◽  
Transmission Electron ◽  
Order Kinetic Model ◽  
Nanocrystalline Iron

Abstract The removal of Ni2+ from aqueous solution by iron nanoparticles encapsulated by graphitic layers (Fe@G) was investigated. Nanoparticles Fe@G were prepared by chemical vapor deposition CVD process using methane as a carbon source and nanocrystalline iron. The properties of Fe@G were characterized by X-ray Diffraction method (XRD), High-Resolution Transmission Electron Microscopy (HRTEM), Fourier Transform-Infrared Spectroscopy (FTIR), BET surface area and zeta potential measurements. The effects of initial Ni2+ concentration (1–20 mg L−1), pH (4–11) and temperature (20–60°C) on adsorption capacity were studied. The adsorption capacity at equilibrium increased from 2.96 to 8.78 mg g−1, with the increase in the initial concentration of Ni2+ from 1 to 20 mg L−1 at pH 7.0 and 20oC. The experimental results indicated that the maximum Ni2+ removal could be attained at a solution pH of 8.2 and the adsorption capacity obtained was 9.33 mg g−1. The experimental data fitted well with the Langmuir model with a monolayer adsorption capacity of 9.20 mg g−1. The adsorption kinetics was found to follow pseudo-second-order kinetic model. Thermodynamics parameters, ΔHO, ΔGO and ΔSO, were calculated, indicating that the adsorption of Ni2+ onto Fe@G was spontaneous and endothermic in nature.

scholarly journals Single-Step Hydrothermal Synthesis of Biochar from H3PO4-Activated Lettuce Waste for Efficient Adsorption of Cd(II) in Aqueous Solution

Molecules ◽  
2022 ◽  
Vol 27 (1) ◽  
pp. 269
Author(s):  
Quyun Chen ◽  
Tian C. Zhang ◽  
Like Ouyang ◽  
Shaojun Yuan
Keyword(s):  
Heavy Metals ◽  
Aqueous Solution ◽  
Low Temperature ◽  
Low Cost ◽  
Hydrothermal Carbonization ◽  
Single Step ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Solution Ph ◽  
Order Kinetic Model

Developing an ideal and cheap adsorbent for adsorbing heavy metals from aqueous solution has been urgently need. In this study, a novel, effective and low-cost method was developed to prepare the biochar from lettuce waste with H3PO4 as an acidic activation agent at a low-temperature (circa 200 °C) hydrothermal carbonization process. A batch adsorption experiment demonstrated that the biochar reaches the adsorption equilibrium within 30 min, and the optimal adsorption capacity of Cd(II) is 195.8 mg∙g−1 at solution pH 6.0, which is significantly improved from circa 20.5 mg∙g−1 of the original biochar without activator. The fitting results of the prepared biochar adsorption data conform to the pseudo-second-order kinetic model (PSO) and the Sips isotherm model, and the Cd(II) adsorption is a spontaneous and exothermic process. The hypothetical adsorption mechanism is mainly composed of ion exchange, electrostatic attraction, and surface complexation. This work offers a novel and low-temperature strategy to produce cheap and promising carbon-based adsorbents from organic vegetation wastes for removing heavy metals in aquatic environment efficiently.

scholarly journals High Selectivity and Reusability of Biomass-Based Adsorbent for Chloramphenicol Removal

Nanomaterials ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 2950
Author(s):  
Weinan Xing ◽  
Qi Liu ◽  
Jingyi Wang ◽  
Siye Xia ◽  
Li Ma ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Solution Structure ◽  
Low Cost ◽  
Water Environment ◽  
Significant Loss ◽  
Order Kinetic ◽  
Solution Ph ◽  
Suitable Material ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Recently, biomass-based materials have attracted increasing attention because of their advantages of low cost, environment-friendly and nonpollution. Herein, the feasibility of using corn stalk biomass fiber (CF) and Fe3O4 embedded chitosan (CS) as a novel biomass-based adsorbent (CFS) to remove chloramphenicol (CAPC) from aqueous solution. Structure of CFS was characterized by using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Brunauer–Emmett–Teller (BET), scanning electron microscopy (SEM) and zeta potential techniques. The effects of solution pH, adsorption time and ion strength on the adsorption capacity were examined. Adsorption isotherms obtained from batch experiments were better fitted by Langmuir model compared with Freundlich model, Dubinin–Radushkevich model and Temkin model. Adsorption kinetic data matched well to the pseudo-second order kinetic model. CAPC adsorption was endothermic, spontaneous, and entropy-increasing nature on CFS. In addition, the CFS could be separated by an external magnetic field, recycled, and reused without any significant loss in the adsorption capacity of CAPC. Based on these excellent performances, there is potential that CFS can be considered as a proficient and economically suitable material for the CAPC removal from the water environment.

scholarly journals Removing Pb(II) Ions from Aqueous Solution by a Promising Absorbent of Tannin-Immobilized Cellulose Microspheres

Polymers ◽  
2019 ◽  
Vol 11 (3) ◽  
pp. 548 ◽  
Author(s):  
Ying Pei ◽  
Gaoqiang Xu ◽  
Xiao Wu ◽  
Keyong Tang ◽  
Guozhen Wang
Keyword(s):  
Aqueous Solution ◽  
Physical Adsorption ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Adsorption Behaviors ◽  
Initial Ph ◽  
Effects Of Ph ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Tannin/cellulose microspheres (T/C) were successfully prepared via a facile homogeneous reaction in a water/oil (W/O) emulsion for removing Pb(II) ions from aqueous solution. The structure of the microspheres was characterized by scanning electron microscopy (SEM), Fourier-transform infrared (FTIR) spectroscopy, and a zeta potential test. The effects of pH, adsorbent dosage, contact time, and temperature on adsorption ability were investigated. The results showed that T/C microspheres could combine Pb(II)ions via electrostatic attractions and physical adsorption. Adsorption kinetics could be better described by the pseudo-second-order kinetic model. The adsorption behaviors were in agreement with the Langmuir adsorption isotherm model with a fitting correlation coefficient of 0.9992. The maximum adsorption capacity was 23.75 mg/g from the Langmuir isotherm evaluation at 308K with an initial pH of 5. The results suggested that tannin/cellulose microspheres could be a low-cost and effective adsorbent for removing Pb(II) ions from aqueous solution.

scholarly journals Application of Acacia karroo charcoal for desalinating Ni(II) and Zn(II) from aqueous solutions through batch mode

2013 ◽  
Vol 3 (3) ◽  
pp. 268-276
Author(s):  
Joginder Singh ◽  
Renu Sharma ◽  
Amjad Ali
Keyword(s):  
Aqueous Solution ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Solution Ph ◽  
Batch Mode ◽  
Acacia Karroo ◽  
Biosorption Process ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Heavy Metals Ions

Acacia karroo charcoal lumps were used for the biosorption of Ni(II) and Zn(II) from an aqueous solution using batch mode. The effect of various parameters viz., solution pH, adsorbent dose, contact time and initial metal concentrations were studied. Freundlich and Langmuir isotherm models were applied to the batch equilibrium data. The maximum biosorption capacity (qmax) for Ni(II) and Zn(II) was found to be 9.0 and 7.99 mg g−1 at pH 6.0 and 4.0 respectively. Experiments were performed to study the kinetics of Ni(II) and Zn(II) biosorption and the data obtained was best fitted to the pseudo-second-order kinetic model. Gibbs free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) changes were also calculated and the observed values supported the spontaneity of the biosorption process. The exhausted adsorbent was regenerated three times using 0.1 N NaOH and its regeneration capacity was evaluated. These results illustrate that A. karroo charcoal lumps hold good potential for removing heavy metals ions from aqueous solution and could be used for desalinating metal ions from industrial wastewater.

scholarly journals Study on the adsorption of methylene blue from aqueous solution using hydrogel glucomannan/graphene oxide

2021 ◽  
Vol 10 (1) ◽  
pp. 59-66
Author(s):  
Son Le Lam ◽  
Phu Nguyen Vinh ◽  
Hieu Le Trung ◽  
Tan Le Thua ◽  
Nhan Dang Thi Thanh ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Graphene Oxide ◽  
Adsorption Capacity ◽  
Organic Dyes ◽  
Dye Adsorption ◽  
Order Kinetic ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Glucomannan/graphene oxide (GM/GO) hydrogel was synthesized by using calcium hydroxide as the crosslinker. The synthesized material was characterized by using IR, XRD, SEM, EDX and RAMAN technology. The composite hydrogel was used for removal of organic dyes from aqueous solution. The results showed that the GM/GO hydrogel had a porous structure and a high adsorption capacity toward methylene blue (MB). The pseudo-second-order kinetic model could fit the rate equation of MB adsorption onto the GM/GO hydrogel. The adsorption of MB onto GM/GO hydrogel was a spontaneous process. In addition, the equilibrium adsorption isotherm data indicated that equilibrium data were fitted to the Langmuir isotherm and the maximum dye adsorption capacity was 198,69 mg.g-1. Moreover, the hydrogel was stable and easily recovered and adsorption capacity was around 97% of the initial saturation adsorption capacity after being used five times.

scholarly journals Preparation of bio-absorbents by modifying licorice residue via chemical methods and removal of copper ions from wastewater

2021 ◽  
Author(s):  
Xiaochun Yin ◽  
Nadi Zhang ◽  
Meixia Du ◽  
Hai Zhu ◽  
Ting Ke
Keyword(s):  
Adsorption Capacity ◽  
Copper Ions ◽  
Order Kinetic ◽  
Solution Ph ◽  
Chemical Methods ◽  
Simple Strategy ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Surface Active ◽  
Adsorption Desorption

Abstract In this paper, a series of bio-adsorbents (LR-NaOH, LR-Na2CO3 and LR-CA) were successfully prepared by modifying Licorice Residue with NaOH, Na2CO3 and citric acid, which were used as the adsorbents to remove Cu2+ from wastewater. The morphology and structure of bio-adsorbents were characterized by Fourier Transform Infrared, SEM, TG and XRD. Using static adsorption experiments, the effects of the adsorbent dosage, the solution pH, the adsorption time, and the initial Cu2+ concentration on the adsorption performance of the adsorbents were investigated. The results showed that the adsorption process of Cu2+ by the bio-adsorbents can be described by pseudo-second order kinetic model and the Langmuir model. The surface structure of the LR-NaOH, LR-Na2CO3 and LR-CA changed obviously, and the surface-active groups increased. The adsorption capacity of raw LR was 21.56 mg/g, LR-NaOH, LR- Na2CO3 significantly enhanced this value up to 43.65 mg/g, 43.55 mg/g, respectively. After four adsorption-desorption processes, the adsorption capacity of LR-NaOH also maintained about 73%. Therefore, LR-NaOH would be a promising adsorbent for removing Cu2+ from wastewater, and the simple strategy towards preparation of adsorbent from the waste residue can be as a potential approach using in the water treatment.

scholarly journals Equilibrium, Kinetics, and Thermodynamics of the Removal of Nickel(II) from Aqueous Solution Using Cow Hooves

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
I. Osasona ◽  
O. O. Ajayi ◽  
A. O. Adebayo
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Room Temperature ◽  
Physical Adsorption ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Equilibrium Studies ◽  
Equilibrium Data

The feasibility of using powdered cow hooves (CH) for removing Ni2+ from aqueous solution was investigated through batch studies. The study was conducted to determine the effect of pH, adsorbent dosage, contact time, adsorbent particle size, and temperature on the adsorption capacity of CH. Equilibrium studies were conducted using initial concentration of Ni2+ ranging from 15 to 100 mgL−1 at 208, 308, and 318 K, respectively. The results of our investigation at room temperature indicated that maximum adsorption of Ni2+ occurred at pH 7 and contact time of 20 minutes. The thermodynamics of the adsorption of Ni2+ onto CH showed that the process was spontaneous and endothermic. Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models were used to quantitatively analysed the equilibrium data. The equilibrium data were best fitted by Freundlich isotherm model, while the adsorption kinetics was well described by pseudo-second-order kinetic equation. The mean adsorption energy obtained from the D-R isotherm revealed that the adsorption process was dominated by physical adsorption. Powdered cow hooves could be utilized as a low-cost adsorbent at room temperature under the conditions of pH 7 and a contact time of 20 minutes for the removal of Ni(II) from aqueous solution.

Assessment of Urtica as a low-cost adsorbent for methylene blue removal: kinetic, equilibrium, and thermodynamic studies

2015 ◽  
Vol 69 (7) ◽  
Author(s):  
Mohammad Peydayesh ◽  
Mojgan Isanejad ◽  
Toraj Mohammadi ◽  
Seyed Mohammad Reza Seyed Jafari
Keyword(s):  
Methylene Blue ◽  
Adsorption Process ◽  
Low Cost ◽  
Cost Effective ◽  
Sem Analysis ◽  
Order Kinetic ◽  
Solution Ph ◽  
Factors Affecting ◽  
Order Kinetic Model ◽  
Mb Adsorption

AbstractMethylene blue (MB) removal using eco-friendly, cost-effective, and freely available Urtica was investigated. The morphology of the adsorbent surface and the nature of the possible Urtica and MB interactions were examined using SEM analysis and the FTIR technique, respectively. Various factors affecting MB adsorption such as adsorption time, initial MB concentration, temperature, and solution pH were investigated. The adsorption process was analysed using different kinetic models and isotherms. The results showed that the MB adsorption kinetic follows a pseudo-second-order kinetic model and the isotherm data fit the Langmuir isotherm well. Thermodynamic parameters, such as ΔG°, ΔH°, and ΔS°, were also evaluated, and the results indicated that the adsorption process is endothermic and spontaneous in nature. The MB adsorption capacity of Urtica was found to be as high as 101.01 mg g

Characterization of Durian Seed Starch/PVOH Composite Hydrogel as a Potential Adsorbent for Removal of Hazardous Dyes

2014 ◽  
Vol 931-932 ◽  
pp. 286-290 ◽  
Author(s):  
W. Pimpa ◽  
C. Pimpa
Keyword(s):  
Adsorption Capacity ◽  
Synthetic Dyes ◽  
Order Kinetic ◽  
Solution Ph ◽  
Environment Friendly ◽  
Composite Hydrogels ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Durian Seed

The intention of this study was to prepare the environment friendly durian seed starch/polyvinyl alcohol (DSS/PVOH) composite hydrogels modified by chemical cross-linking with glutaraldehyde and to assess the adsorption potential of the DSS/PVOH composite hydrogels for the removal of the synthetic dyes from aqueous solution. The hydrogels were characterized by swelling behavior and scanning electron microscope (SEM). The effect of DSS content and initial dye solution pH on the adsorption capacity was studied conducting batch experiment system. The DSS/PVOH composite hydrogels consisting 3% DSS has optimum adsorption capacity of 3.411 mg/g (for methylene blue under the condition of pH 7) and 3.274 mg/g (for acid orange 8 under the condition of pH 2.5) at 24 h of contact time. The adsorptions were well fitted by the pseudo-second order kinetic model. It was indicated that the mechanism of removal predominant is effective for low dye concentrations, below 10 mg/l.

Sign in / Sign up

Export Citation Format

Share Document