THERMAL GRAVIMETRIC AND ACTIVATION ENERGY ANALYSIS OF RENEWABLE POLYMER UPON ULTRAVIOLET (UV) IRRADIATION

2015 ◽  
Vol 77 (32) ◽  
Author(s):  
Nik Normunira Mat Hassan ◽  
Anika Zafiah M. Rus
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Uv Irradiation ◽  
Hard Segment ◽  
Soft Segment ◽  
Great Influence ◽  
Automotive Application ◽  
Polymer Foam ◽  
Wide Range ◽  
Thermal Stability Of

Renewable polymer made from renewable material is one of the most important groups of polymer because of their versatility and they can be manufactured in a wide range of insulation and automotive application. In this project, renewable polymer based on waste vegetable oil were synthesized and crosslink with commercial polymethane polyphenyl isocyanate. The renewable polymer foam (RPF) was compressed by using hot compression moulding technique at 90 oC based on the evaporation of volatile matter and known as compressed renewable polymer (CRP). The thermal degradation and activation energy of RPF and CRP samples is consistant with the increasing of UV irradiation time at the first degradation, second degradation and third degradation. This is due to thermal stability of samples at the hard segment has a great influence on the thermal stability of soft segment. A higher thermal stability of hard segment leads to a higher degradation temperature of soft segment.

scholarly journals Investigating Physio-Thermo-Mechanical Properties of Polyurethane and Thermoplastics Nanocomposite in Various Applications

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2467
Author(s):  
Tyser Allami ◽  
Ahmed Alamiery ◽  
Mohamed H. Nassir ◽  
Amir H. Kadhum
Keyword(s):  
Thermal Stability ◽  
Electrical Properties ◽  
Hard Segment ◽  
Soft Segment ◽  
Thermoplastic Polyurethane ◽  
Tensile Modulus ◽  
Scanning Calorimetry ◽  
Strain Behavior ◽  
Phase Separation Kinetics ◽  
Thermal Stability Of

The effect of the soft and hard polyurethane (PU) segments caused by the hydrogen link in phase-separation kinetics was studied to investigate the morphological annealing of PU and thermoplastic polyurethane (TPU). The significance of the segmented PUs is to achieve enough stability for further applications in biomedical and environmental fields. In addition, other research focuses on widening the plastic features and adjusting the PU–polyimide ratio to create elastomer of the poly(urethane-imide). Regarding TPU- and PU-nanocomposite, numerous studies investigated the incorporation of inorganic nanofillers such as carbon or clay to incorporating TPU-nanocomposite in several applications. Additionally, the complete exfoliation was observed up to 5% and 3% of TPU–clay modified with 12 amino lauric acid and benzidine, respectively. PU-nanocomposite of 5 wt.% Cloisite®30B showed an increase in modulus and tensile strength by 110% and 160%, respectively. However, the nanocomposite PU-0.5 wt.% Carbone Nanotubes (CNTs) show an increase in the tensile modulus by 30% to 90% for blown and flat films, respectively. Coating PU influences stress-strain behavior because of the interaction between the soft segment and physical crosslinkers. The thermophysical properties of the TPU matrix have shown two glass transition temperatures (Tg’s) corresponding to the soft and the hard segment. Adding a small amount of tethered clay shifts Tg for both segments by 44 °C and 13 °C, respectively, while adding clay from 1 to 5 wt.% results in increasing the thermal stability of TPU composite from 12 to 34 °C, respectively. The differential scanning calorimetry (DSC) was used to investigate the phase structure of PU dispersion, showing an increase in thermal stability, solubility, and flexibility. Regarding the electrical properties, the maximum piezoresistivity (10 S/m) of 7.4 wt.% MWCNT was enhanced by 92.92%. The chemical structure of the PU–CNT composite has shown a degree of agglomeration under disruption of the sp2 carbon structure. However, with extended graphene loading to 5.7 wt.%, piezoresistivity could hit 10-1 S/m, less than 100 times that of PU. In addition to electrical properties, the acoustic behavior of MWCNT (0.35 wt.%)/SiO2 (0.2 wt.%)/PU has shown sound absorption of 80 dB compared to the PU foam sample. Other nanofillers, such as SiO2, TiO2, ZnO, Al2O3, were studied showing an improvement in the thermal stability of the polymer and enhancing scratch and abrasion resistance.

Meyer-Neldel Rule on thermal stability parameters (trap depth and frequency factor) of luminescence signals in quartz

2021 ◽  
Author(s):  
Zuzanna Kabacińska ◽  
Alida Timar-Gabor ◽  
Benny Guralnik
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Hydrogen Diffusion ◽  
Dose Range ◽  
Accurate Determination ◽  
Frequency Factor ◽  
Proton Conduction ◽  
High Dose ◽  
Compensation Law ◽  
Thermal Stability Of

<p>Thermally activated processes can be described mathematically by the Arrhenius equation. The Meyer-Neldel Rule (MNR), or compensation law, linearly relates the pre-exponent term to the logarithm of the excitation enthalpy for processes that are thermally driven in an Arrhenian manner. This empirical rule was observed in many areas of materials science, in physics, chemistry, and biology. In geosciences it was found to uphold in hydrogen diffusion (Jones 2014a) and proton conduction (Jones 2014b) in minerals.</p><p>Trapped charge dating methods that use electron spin resonance (ESR) or optically or thermally stimulated luminescence (OSL and TL) are based on the dose-dependent accumulation of defects in minerals such as quartz and feldspar. The thermal stability of these defects in the age range investigated is a major prerequisite for accurate dating, while the accurate determination of the values of the trap depths and frequency factors play a major role in thermochronometry applications. </p><p>The correlation of kinetic parameters for diffusion has been very recently established for irradiated oxides (Kotomin et al. 2018). A correlation between the activation energy and the frequency factor that satisfied the Meyer–Neldel rule was reported when the thermal stability of [AlO<sub>4</sub>/h<sup>+</sup>]<sup>0</sup> and [TiO<sub>4</sub>/M<sup>+</sup>]<sup>0</sup> ESR signals in quartz was studied as function of dose (Benzid and Timar-Gabor 2020). Here we compiled the optically stimulated luminescence (OSL) data published so far in this regard, and investigated experimentally the thermal stability of OSL signals for doses ranging from 10 to 10000 Gy in sedimentary quartz samples. We report a linear relationship between the natural logarithm of the preexponent term (the frequency factor) and the activation energy E, corresponding to a Meyer-Neldel energy of 45 meV, and a deviation from first order kinetics in the high dose range accompanied by an apparent decrease in thermal stability. The implications of these observations and the atomic and physical mechanisms are currently studied.</p><p> </p><p><strong>References</strong></p><p>Benzid, K., Timar Gabor, A. 2020. The compensation effect (Meyer–Neldel rule) on [AlO<sub>4</sub>/h<sup>+</sup>]<sup>0</sup> and [TiO<sub>4</sub>/M<sup>+</sup>]<sup>0</sup> paramagnetic centers in irradiated sedimentary quartz. <em>AIP Advance</em>s 10, 075114.</p><p>Kotomin, E., Kuzovkov, V., Popov, A. I., Maier, J., and Vila, R. 2018. Anomalous kinetics of diffusion-controlled defect annealing in irradiated ionic solids. <em>J. Phys. Chem. A</em> 122(1), 28–32</p><p>Jones, A. G. (2014a), Compensation of the Meyer-Neldel Compensation Law for H diffusion in minerals, <em>Geochem. Geophys. Geosyst.</em>, 15, 2616–2631</p><p>Jones, A. G. (2014b), Reconciling different equations for proton conduction using the Meyer-Neldel compensation rule, <em>Geochem. Geophys. Geosyst</em>., 15, 337–349</p>

Thermal Stability of Ultrafine-Grained Pure Titanium Processed by High-Pressure Torsion

2021 ◽  
Vol 1016 ◽  
pp. 338-344
Author(s):  
Wan Ji Chen ◽  
Jie Xu ◽  
De Tong Liu ◽  
De Bin Shan ◽  
Bin Guo ◽  
...  
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Grain Size ◽  
High Pressure ◽  
Annealing Temperature ◽  
High Pressure Torsion ◽  
Stored Energy ◽  
Ultrafine Grained ◽  
Average Grain Size ◽  
Thermal Stability Of

High-pressure torsion (HPT) was conducted under 6.0 GPa on commercial purity titanium up to 10 turns. An ultrafine-grained (UFG) pure Ti with an average grain size of ~96 nm was obtained. The thermal properties of these samples were studied by using differential scanning calorimeter (DSC) which allowed the quantitative determination of the evolution of stored energy, the recrystallization temperatures, the activation energy involved in the recrystallization of the material and the evolution of the recrystallized fraction with temperature. The results show that the stored energy increases, beyond which the stored energy seems to level off to a saturated value with increase of HPT up to 5 turns. An average activation energy of about 101 kJ/mol for the recrystallization of 5 turns samples was determined. Also, the thermal stability of the grains of the 5 turns samples with subsequent heat treatments were investigated by microstructural analysis and Vickers microhardness measurements. It is shown that the average grain size remains below 246 nm when the annealing temperature is below 500 °C, and the size of the grains increases significantly for samples at the annealing temperature of 600 °C.

Synthesis of Fe-rich Fe–Al nanocrystalline solid solutions using ball milling

1999 ◽  
Vol 14 (5) ◽  
pp. 1760-1770 ◽  
Author(s):  
H. G. Jiang ◽  
H. M. Hu ◽  
E. J. Lavernia
Keyword(s):  
Heat Treatment ◽  
Activation Energy ◽  
Thermal Stability ◽  
Intermetallic Compound ◽  
Ball Milling ◽  
Microstructural Evolution ◽  
Solid Solutions ◽  
Al Alloys ◽  
Time Intervals ◽  
Thermal Stability Of

The synthesis of nanocrystalline Fe, Fe–4 wt% Al, and Fe–10 wt% Al solid solutions by SPEX ball milling has been studied. The microstructural evolution during ball milling, as well as subsequent heat treatment, has been characterized. The results demonstrate that ball milling promotes the formation of αFe–4 wt% Al and αFe–10 wt% Al solid solutions by reducing the activation energy of these alloys and generating thermal energy during this process. For Fe–10 wt% Al powders milled for various time intervals up to approximately 20 min, the FeAl intermetallic compound is formed. For alloys annealed at temperatures ranging from 600 to 1000 °C, the addition of 10 wt% Al to Fe significantly enhances the thermal stability of the nanocrystalline Fe–Al alloys. Interestingly, the addition of Al within the range of 4–10 wt% seems to have little effect on the thermal stability of these alloys annealed under the same conditions. Also, the thermal stability improves for alloys milled in air as opposed to those processed using Ar.

Epoxy Cured with Anhydride Terminated Polydimethylsiloxane: Cure Kinetics and Thermal Properties

2011 ◽  
Vol 415-417 ◽  
pp. 261-264
Author(s):  
Yuan Ren ◽  
Zheng Xi ◽  
Wen Jun Gan ◽  
Liang Zhang ◽  
Jing Zhang ◽  
...  
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Thermal Properties ◽  
Succinic Anhydride ◽  
Cure Kinetics ◽  
Diglycidyl Ether ◽  
Scanning Calorimetry ◽  
Thermogravimetric Analyses ◽  
Isothermal Measurements ◽  
Thermal Stability Of

A siloxane-containing dianhydride, succinic anhydride terminated polydimethylsiloxane (DMS-Z21) was selected to cure diglycidyl ether of bisphenol-A based epoxy resin (DGEBA). The cure kinetics and thermal properties were investigated by nonisothermal and isothermal differential scanning calorimetry (DSC) and thermogravimetric analyses (TGA), respectively. The activation energy (Ea) of the curing reaction was obtained based on the methods of Kissinger and isothermal measurements. The results of the thermogravimetric analyses of the DGEBA/DMS-Z21 system showed that the thermal stability of the DGEBA/DMS-Z21 system was slightly higher than the DGEBA/MeTHPA system.

Thermal Decomposition of Supersaturated Ti1-xAlxN Solid Solution Synthesized by High-Energy Milling

2016 ◽  
Vol 9 ◽  
pp. 82-89
Author(s):  
Maya Radune ◽  
Michael Zinigrad ◽  
David Fuks ◽  
S. Hayun ◽  
Nachum Frage
Keyword(s):  
Thermal Stability ◽  
Solid Solution ◽  
Spinodal Decomposition ◽  
Density Functional ◽  
Chemical Deposition ◽  
High Energy ◽  
Nucleation And Growth ◽  
Scanning Calorimetry ◽  
Wide Range ◽  
Thermal Stability Of

Supersaturated titanium-aluminum nitride (Ti1-xAlxN) is a very attractive material for a wide range of applications due to its high oxidation and wear resistance accompanied by high strength, hardness, thermal conductivity and thermal shock resistance. Currently, its applications are limited to coatings obtained by physical or chemical deposition. Bulk materials based on Ti1-xAlxN may be fabricated by powder metallurgy approach using powders synthesized by high-energy ball milling (HEBM), which composition corresponds to supersaturated Ti1-xAlxN solid solution. In the present study, thermal stability of the supersaturated Ti1-xAlxN solid solution was investigated. According to the quasi-binary TiN-AlN phase diagram, constructed using density functional theory (DFT) analysis, the concentration ranges, where decomposition takes place through spinodal decomposition or through nucleation and growth, were determined. Experimental study on thermal stability of solid Ti1-xAlxN solution powder was conducted by means of differential scanning calorimetry (DSC), Brunauer-Emmited-Teller (BET) and XRD. The results indicated that spinodal decomposition of Ti1-xAlxN starts at 800°C, while at temperature higher than 1300°C regular decomposition (nucleation and growth) is occur.

Studies on Thermal Stability and Rheological Property of PU/PVDF Blend

2011 ◽  
Vol 311-313 ◽  
pp. 1065-1070
Author(s):  
Guo Lan Huan ◽  
Jian Li Liu ◽  
Qi Yun Du ◽  
Xiao Yu Hu
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Thermal Decomposition ◽  
Shear Stress ◽  
Rheological Property ◽  
Decomposition Temperature ◽  
Dynamic Equations ◽  
Thermal Decomposition Temperature ◽  
Thermal Stability Of ◽  
Decomposition Activation Energy

In this article, the thermal stability of PU/PVDF blend was investigated by thermogravimetry (TG), and their rheological property was studied through testing and analyzing the rheological curves. The results showed that, with the increase in PVDF content, the thermal decomposition temperature of PU/PVDF blend increased, and by fitting relevant data to thermal decomposition dynamic equations, it was found that thermal decomposition activation energy of the blend increased gradually, i.e. the thermal stability of the blend increased gradually. Meantime, based on the curves of shear stress vs. shear rate of the blend at 180°C and 200°C, it was shown that for PU/PVDF blend, with the decrease of temperature and the increase in PVDF content, the non-Newtonian index decreased, while the viscosity of the blend increased.

scholarly journals Experimental Investigation of Thermal Characteristics of Kiwira Coal Waste with Rice Husk Blends for Gasification

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Deodatus Kazawadi ◽  
Geoffrey R. John ◽  
Cecil K. King’ondu
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Rice Husk ◽  
Energy Recovery ◽  
Fossil Fuels ◽  
High Energy ◽  
Coal Waste ◽  
Rice Husks ◽  
Weight Percentage ◽  
Thermal Stability Of

Eminent depletion of fossil fuels and environmental pollution are the key forces driving the implementation cofiring of fossil fuels and biomass. Cogasification as a technology is known to have advantages of low cost, high energy recovery, and environmental friendliness. The performance/efficiency of this energy recovery process substantially depends on thermal properties of the fuel. This paper presents experimental study of thermal behavior of Kiwira coal waste/rice husks blends. Compositions of 0, 20, 40, 60, 80, and 100% weight percentage rice husk were studied using thermogravimetric analyzer at the heating rate of 10 K/min to 1273 K. Specifically, degradation rate, conversion rate, and kinetic parameters have been studied. Thermal stability of coal waste was found to be higher than that of rice husks. In addition, thermal stability of coal waste/rice husk blend was found to decrease with an increase of rice husks. In contrast, both the degradation and devolatilization rates increased with the amount of rice husk. On the other hand, the activation energy dramatically reduced from 131 kJ/mol at 0% rice husks to 75 kJ/mol at 100% rice husks. The reduction of activation energy is advantageous as it can be used to design efficient performance and cost effective cogasification process.

Thermal Stability of Z-Type Perfluoro Poly Ether Lubricant Polymers: A Combined Thermogravimetric and Temperature Programmed Desorption Study

2003 ◽  
Author(s):  
Paul M. Jones ◽  
Lei Li ◽  
Yiao-Tee Hsia
Keyword(s):  
Activation Energy ◽  
Thermal Stability ◽  
Temperature Programmed Desorption ◽  
Kcal Mole ◽  
Three Samples ◽  
Desorption Study ◽  
Polymer Decomposition ◽  
Temperature Programmed ◽  
Decomposition Chemistry ◽  
Thermal Stability Of

The thermal stability of Zdol 4000, 7800 and Ztetraol perfluoropolyethers (PFPE) have been studied in both the bulk with thermogravimetric analysis (TGA) and in thin film form with temperature programmed desorption spectroscopy (TPD). The TGA results have been interpreted to yield an evaporation activation energy for both Zdol 4000 (13 kcal/mole) and Zdol 7800 (19 kcal/mole). A larger activation energy is also found for all three samples investigated that is consistent with polymer decomposition (22, 27 and 21 kcal/mole respectively). The TPD threshold has been found to be approximately similar all three samples (∼500 K). The temperature of decomposition was also found to be similar for all three samples and was dominated by the CF2O+ mass fragment at ∼660 K. Two desorption maximums were observed for both Zdol 4000 and Ztetraol indicating the similarity in their decomposition chemistry. In contrast only one desorption peak was observed from Zdol 7800 (675 K). A CF3+ fragment was not observed in any of the TPD spectra indicating the absence an acidic decomposition path for all of the Fomblin Z polymers studied.

Sign in / Sign up

Export Citation Format

Share Document