SIMULATION OF ORGANIC RANKINE CYCLE THROUGH FLUEGAS TO LARGE SCALE ELECTRICITY GENERATION PURPOSE

2015 ◽  
Vol 77 (27) ◽  
Author(s):  
Omid Rowshanaie ◽  
Saari Mustapha ◽  
Kamarul Arifin Ahmad ◽  
Hooman Rowshanaie
Keyword(s):  
Heat Exchanger ◽  
Large Scale ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Steady State Condition ◽  
Working Fluids ◽  
Tube Heat Exchanger ◽  
Heat Transfer Capacity ◽  
Mass Flow Rates ◽  
Shell And Tube

A simulation model of Organic Rankine Cycle (ORC) was developed with HYSYS software driven by R245fa, with NOVEC7000 and R141b as working fluids and Fluegas of boilers as a heat source of shell and tube Heat Exchanger to generate large scale electricity. The initial working condition was in subcooled liquid and steady state condition. R141b was found to generate the highest electricity power increment in specific mass flow rates and inlet pressures of Expander because of approaching its critical temperature to inlet Fluegas temperature. Howeever, in terms of economic considerations and cost of shell and tube Heat Exchanger that related to total heat transfer capacity, NOVEC7000 is the optimum selection. Furthermore, R245fa has the highest total effiiciency of ORC compared with other working fluids in this study.

scholarly journals Performance assessment of shell and tube heat exchanger based subcritical and supercritical organic Rankine cycles

2018 ◽  
Vol 22 (Suppl. 3) ◽  
pp. 855-866
Author(s):  
Anil Erdogan ◽  
Ozgur Colpan
Keyword(s):  
Heat Exchanger ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
System Level ◽  
Two Phase ◽  
Detailed Model ◽  
Tube Heat Exchanger ◽  
Organic Rankine Cycles ◽  
Level Model ◽  
Shell And Tube

In this study, thermal models for subcritical and supercritical geothermal powered organic Rankine cycles are developed to compare the performance of these cycle configurations. Both of these models consist of a detailed model for the shell and tube heat exchanger integrating the geothermal and organic Rankine cycles sides and basic thermodynamic models for the rest of the components of the cycle. In the modeling of the heat exchanger, this component was divided into sever?al zones and the outlet conditions of each zone were found applying logarithmic mean temperature difference method. Different Nusselt correlations according to the relevant phase (single, two-phase, and supercritical) were also included in this model. Using the system-level model, the effect of the source temperature on the performances of the heat exchanger and the organic Rankine cycle was assessed. These performance parameters are heat transfer surface area and pressure drop of tube side fluid for the heat exchanger, and electrical and exergetic efficiencies of the integrated organic Rankine cycles system. It was found that 44.12% more net power is generated when the supercritical organic Rankine cycle is used compared to subcritical organic Rankine cycle.

scholarly journals Modelling of Polymeric Shell and Tube Heat Exchangers for Low-Medium Temperature Geothermal Applications

Energies ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2737
Author(s):  
Francesca Ceglia ◽  
Adriano Macaluso ◽  
Elisa Marrasso ◽  
Maurizio Sasso ◽  
Laura Vanoli
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Power Plants ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Heat Transfer Area ◽  
Geothermal Fluid ◽  
Shell And Tube

Improvements in using geothermal sources can be attained through the installation of power plants taking advantage of low and medium enthalpy available in poorly exploited geothermal sites. Geothermal fluids at medium and low temperature could be considered to feed binary cycle power plants using organic fluids for electricity “production” or in cogeneration configuration. The improvement in the use of geothermal aquifers at low-medium enthalpy in small deep sites favours the reduction of drilling well costs, and in addition, it allows the exploitation of local resources in the energy districts. The heat exchanger evaporator enables the thermal heat exchange between the working fluid (which is commonly an organic fluid for an Organic Rankine Cycle) and the geothermal fluid (supplied by the aquifer). Thus, it has to be realised taking into account the thermodynamic proprieties and chemical composition of the geothermal field. The geothermal fluid is typically very aggressive, and it leads to the corrosion of steel traditionally used in the heat exchangers. This paper analyses the possibility of using plastic material in the constructions of the evaporator installed in an Organic Rankine Cycle plant in order to overcome the problems of corrosion and the increase of heat exchanger thermal resistance due to the fouling effect. A comparison among heat exchangers made of commonly used materials, such as carbon, steel, and titanium, with alternative polymeric materials has been carried out. This analysis has been built in a mathematical approach using the correlation referred to in the literature about heat transfer in single-phase and two-phase fluids in a tube and/or in the shell side. The outcomes provide the heat transfer area for the shell and tube heat exchanger with a fixed thermal power size. The results have demonstrated that the plastic evaporator shows an increase of 47.0% of the heat transfer area but an economic installation cost saving of 48.0% over the titanium evaporator.

Effectiveness Study of a Shell and Tube Heat Exchanger Operated with Nanofluids at Different Mass Flow Rates

2014 ◽  
Vol 65 (7) ◽  
pp. 699-713 ◽  
Author(s):  
I. M. Shahrul ◽  
I. M. Mahbubul ◽  
R. Saidur ◽  
S. S. Khaleduzzaman ◽  
M. F. M. Sabri ◽  
...  
Keyword(s):  
Heat Exchanger ◽  
Mass Flow ◽  
Effectiveness Study ◽  
Flow Rates ◽  
Tube Heat Exchanger ◽  
Mass Flow Rates ◽  
Shell And Tube

Performance Analysis of Shell and Tube Heat Exchanger using Different Nanofluids

2019 ◽  
Vol 11 (4) ◽  
Author(s):  
J. Thavamani
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Mass Flow ◽  
Base Fluid ◽  
Particle Diameter ◽  
Flow Rates ◽  
Tube Heat Exchanger ◽  
Cold Fluid ◽  
Mass Flow Rates ◽  
Shell And Tube

Heat exchanger is the most important function in industrial sector for transferring heat energy to useful work. Heat transfer occurs between the cold fluid and hot fluid or from hot fluid to cold fluid in conduction and convection mode of through a heat exchanger wall. If heat transfer medium has very low thermal conductivity, it would have limited the efficiency of heat exchanger. Whenever the system is subjected to increased heat load, cooling is the main technical challenge for industries. The main objective of this work is to evaluate the effectiveness of shell and tube heat exchanger experimentally and analyse the flow behaviours of different nanofluids. In our experimental analysis, various nanofluids which consist of water and one percentage volume concentration of Al2O3, CuO and SiO2 passing through tube side in the shell and tube heat exchanger. The nano particle diameter is 70nm. The three dissimilar mass flow rates are considered for the experiments and their results are continuously monitored. The enhancement of heat transfer performance of CuO, Al2O3, SiO2 is compared with the base fluid water. Reynolds number values are calculated with three different mass flow rates and compared with heat transfer characteristics (LMTD, Nusselt number and overall heat transfer coefficient). SEM analysis, energy dispersive spectroscopy, X-ray diffraction of CuO, Al2O3 and SiO2.are conducted. The heat transfer effectiveness is increased by 22.12%, 19.46% and 1.47% respectively for CuO, Al2O3 and SiO2 when compared to base fluid.

Sign in / Sign up

Export Citation Format

Share Document