EVALUATION ON THE PERFORMANCE OF AGED ASPHALT BINDER AND MIXTURE UNDER VARIOUS AGING METHODS

2015 ◽  
Vol 77 (23) ◽  
Author(s):  
Mohd Khairul Idham ◽  
Mohd Rosli Hainin ◽  
M. Naqiuddin M. Warid ◽  
Noor Azah Abdul Raman ◽  
Rosmawati Mamat
Keyword(s):  
Permanent Deformation ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Maximum Aggregate Size ◽  
Asphaltic Concrete ◽  
Air Exposure ◽  
Stiffness Modulus ◽  
Aged Asphalt

Hot mix asphalt (HMA) pavement encounter short and long term aging throughout the service life. Laboratory aging is the method used to simulate field aging process of HMA pavement. This study was undertaken to determine the long term effect of different binder and mixture laboratory aging methods on HMA (binder aging and mixture aging). Three types of HMA mixtures were prepared for this study namely Asphaltic Concrete with 10 mm nominal maximum aggregate size (AC 10), Asphaltic Concrete 14 mm (AC 14) and Asphaltic Concrete 28 mm (AC 28). These specimens were conditioned with nine different methods and durations.  Resilient modulus test was carried out at 40˚C as an initial indicator of the specimen performance. Permanent deformation of the same specimens was then evaluated by dynamic creep test. Generally, the aged asphalt binder specimens have higher resilient and stiffness modulus compared to aged asphalt mixture specimens. In addition, aged binder specimens have a lower permanent strain which indicates higher resistance to permanent deformation. This study also found that high resilient and stiffness modulus of specimens is attributed by different in heating frequency, temperature, air exposure and binder content of the mixtures.

scholarly journals A Comprehensive Evaluation of Rejuvenator on Mechanical Properties, Durability, and Dynamic Characteristics of Artificially Aged Asphalt Mixture

Materials ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 1554 ◽  
Author(s):  
Pan Pan ◽  
Yi Kuang ◽  
Xiaodi Hu ◽  
Xiao Zhang
Keyword(s):  
Mechanical Properties ◽  
Dynamic Characteristics ◽  
Comprehensive Evaluation ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Physical Property ◽  
Fatigue Property ◽  
Physical Test ◽  
Aged Asphalt

In this study, the aged asphalt binder and mixture were laboratory prepared through short-term ageing testing and long-term ageing testing. Firstly, the effect of rejuvenator on physical properties of aged asphalt binders was investigated. In addition, a series of laboratory tests were performed to evaluate the influence of ageing and rejuvenator content on the mechanical properties, durability and dynamic characteristics of asphalt mixtures. Physical test results of asphalt binder testified that rejuvenator used can efficiently recover the aged asphalt binder. However, the effect of ageing and rejuvenator content exhibits different trends depending on the physical property tests conducted. Moreover, artificially aged asphalt mixture with rejuvenator has better ability to resist moisture damage and ravelling. In addition, the ITSR value is more suitable to evaluate the moisture susceptibility for asphalt recycling. Although rejuvenator improves the thermal cracking resistance and fatigue property of aged asphalt mixture, rejuvenated mixture shows greater modulus and inferior ability to resist reflective cracking than the unaged mixture. Moreover, rejuvenated mixture shows less dependence on frequency at high temperature regions and stronger dependence at low temperature regions compared to unaged and long-term aged mixtures.

scholarly journals Influence of Aramid-Polyolefin Fibers on the Properties of Bituminous Mixtures

2021 ◽  
Vol 1203 (3) ◽  
pp. 032093
Author(s):  
Stanisław Majer ◽  
Bartosz Budziński
Keyword(s):  
Permanent Deformation ◽  
Aggregate Size ◽  
Maximum Aggregate Size ◽  
Cellulose Fibres ◽  
Stiffness Modulus ◽  
Temperature Range ◽  
Bituminous Mixtures ◽  
Aramid Fibres ◽  
Indirect Tension ◽  
Functional Features

Abstract The use of additives in bituminous mixtures such as fibers has been the subject of various studies. Different fibres including cellulose fibres, steel fibres, basalt fibres, glass fibres and aramid fibres can be used to improve the properties of bituminous mixtures. Depending on the type of fibres used, different characteristics can be changed. The paper contains results of comparative tests of bituminous mixtures with aramid-polyolefin fibres. Asphalt concrete used for wearing course with maximum aggregate size of 11 mm was evaluated in the study. Reference mix with an average penetration grade of 50/70 was chosen as a base for modifications. Due to difficulty in preparing mixtures with fibers in a laboratory mixer, test specimens were obtained from a stationary plant. The fibers and aggregate mix was prepared before adding the asphalt. The fibers were added at a rate of 0.5 kg per 1000 kg of finished bituminous mixture. This allowed to obtain an even distribution of fibers in the mixture resulting in a homogeneity necessary for planned tests. This allowed to omit the scale effect, that could occur due to differences between laboratory and stationary mixing. Stiffness modulus tests were performed using the IT-CY (Indirect Tension to Cylindrical Specimens) method for a wide temperature range of 0-30°C. The specimen resistance to permanent deformation was evaluated. Obtained results has shown a clear increase in the resistance to permanent deformation of mixtures with aramid- polyolefin fibers, which is especially important for mixtures used for wearing course. The results has also shown a significant increase in the stiffness modulus regardless of temperature range. Results of conducted experiments has shown that it is possible to reduce the thickness of bituminous overlay in case of reinforcement of the existing pavement structure. The analysis of results has shown that the application of aramid-polyolefin fibres in bituminous mixtures can improve the functional features of the pavement and be beneficial to the investors.

scholarly journals Performance of Waste Cooking Oil on Aged Asphalt Mixture

2018 ◽  
Vol 65 ◽  
pp. 02002
Author(s):  
Ramadhansyah Putra Jaya ◽  
Romana Sarker Lopa ◽  
Norhidayah Abdul Hassan ◽  
Haryati Yaacob ◽  
Mohamad Idris Ali ◽  
...  
Keyword(s):  
Resilient Modulus ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Acid Value ◽  
Waste Cooking Oil ◽  
Cooking Oil ◽  
Maintenance And Rehabilitation ◽  
Aged Asphalt ◽  
Marshall Stability

Asphaltic concrete pavement is popular worldwide, but this type of pavement requires frequent maintenance and rehabilitation as it cannot cope up with the increasing number of traffic vehicles and loads. Therefore, modifying asphalt pavement to reduce the damages and defects is necessary, thereby enhancing the serviceability of pavement. This study presents the effect of waste cooking oil on asphalt mixture at different ageing conditions. A 60/70 penetration-grade asphalt binder was used, and 5% of this binder was replaced with untreated and treated waste cooking oil. Asphalt mixtures were prepared at the selected 5% optimum bitumen content and under two tests, i.e. Marshall stability and resilient modulus. The findings showed the better stability and resilient modulus of long-term aged samples incorporated with treated waste cooking oil than the unaged and short-term aged samples. The incorporation of untreated waste cooking oil caused reduced performance compared with the controlled and long-term aged samples. This result can be attributed to the high acid value of waste cooking oil. Therefore, treated waste cooking oil can be used as a binder replacement given its significantly higher performance at the mentioned ageing condition than the controlled mixture.

Evaluation of Viscoelastic and Fracture Properties of Asphalt Mixtures with Long-Term Laboratory Conditioning

2018 ◽  
Vol 2672 (28) ◽  
pp. 503-513 ◽  
Author(s):  
Reyhaneh Rahbar-Rastegar ◽  
Jo Sias Daniel ◽  
Eshan V. Dave
Keyword(s):  
Viscoelastic Properties ◽  
Complex Modulus ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Asphalt Mixtures ◽  
Maximum Aggregate Size ◽  
Cracking Behavior ◽  
Fracture Properties ◽  
Fracture Parameters

Aging affects the properties of asphalt mixtures in different ways; increase of stiffness, decrease of relaxation capability, and the increase of brittleness, resulting in changes in cracking behavior of asphalt mixtures. In this study, ten plant-produced, lab-compacted mixtures with various compositions (recycled materials, binder grades, binder source, and nominal maximum aggregate size) are evaluated at different long-term aging levels (24 hours at 135°C, 5 days at 95°C, and 12 days at 95°C on loose mix and 5 days at 85°C on compacted specimens). The asphalt mixture linear viscoelastic properties (|E*| and δ) and master curve shape parameters measured from complex modulus testing and fracture properties (measured from disc-shaped compact tension and semi-circular bending fracture testing) are compared at different levels of aging. The results indicate that the mixture exposure time to aging is proportional to the dynamic modulus and phase angle changes. Generally, the fracture parameters of mixtures become worse when aging level changes from 5 to 12 days aging. In spite of the similar viscoelastic properties, the mixtures with 24 hours at 135°C and 12 days at 95°C aging do not show similar fracture parameters.

Laboratory Evaluation of a Plant-Produced High Polymer–Content Asphalt Mixture

2017 ◽  
Vol 2631 (1) ◽  
pp. 144-152 ◽  
Author(s):  
Benjamin F. Bowers ◽  
Stacey D. Diefenderfer ◽  
Brian K. Diefenderfer
Keyword(s):  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Asphalt Binders ◽  
Laboratory Evaluation ◽  
Maximum Aggregate Size ◽  
Polymer Content ◽  
High Polymer ◽  
Modified Binder ◽  
Virginia Department

Reflective cracking in asphalt overlays placed over jointed concrete pavements is of major concern in Virginia, as well as nationally, and has generated interest in various reflective crack mitigation techniques that are easy to implement. One technique is the use of binder modifiers, such as asphalt rubber, polymer-modified asphalt binders, or high polymer–content (HP) modified binders. In the summer of 2014, the Virginia Department of Transportation placed an HP asphalt mixture produced by using an asphalt binder that contained approximately 7.5% styrene-butadiene-styrene polymer in a trial section within a subdivision as a low-risk means to assess constructability and laboratory performance. The HP mixture was evaluated in comparison with a typical surface asphalt mixture with a 9.5-mm nominal maximum aggregate size, as a control. Testing was performed on specimens fabricated from reheated control and HP mixture samples, as well as on specimens fabricated from site-compacted samples and road cores of the HP mixture. In addition, binder grading was performed on the control binder and modified binder. The HP binder was significantly more elastic than the control binder. Comparable dynamic moduli were found for reheated mixture specimens, although site-compacted and road core specimens from the HP mixture had lower stiffness than the control mixture. The HP mixture performed better in rutting and in fatigue. The Texas overlay test indicated similar crack resistance between the two mixtures; however, measured loads of the HP specimens were nearly half those of the control specimens. The results of laboratory testing indicated that the mixture incorporating the HP binder should have a far greater fatigue life and rut resistance than the control mixture.

scholarly journals Enhanced Dry Process Method for Modified Asphalt Containing Plastic Waste

2021 ◽  
Vol 8 ◽  
Author(s):  
Hasanain Radhi Radeef ◽  
Norhidayah Abdul Hassan ◽  
Ahmad Razin Zainal Abidin ◽  
Mohd Zul Hanif Mahmud ◽  
Nur Izzi Md. Yusoffa ◽  
...  
Keyword(s):  
Resilient Modulus ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Plastic Waste ◽  
Asphalt Mixtures ◽  
Maximum Aggregate Size ◽  
Dry Process ◽  
Modified Asphalt ◽  
And Performance

In recent years, the proliferation of plastic waste has become a global problem. A potential solution to this problem is the dry process, which incorporates plastic waste into asphalt mixtures. However, the dry process often has inconsistent performance due to poor interaction with binder and improper distribution of plastic waste particles in the mixture skeleton. This inconsistency may be caused by inaccurate mixing method, shredding size, mixing temperature and ingredient priorities. Thus, this study aims to improve the consistency of the dry process by comparing the control asphalt mixture and two plastic waste-modified asphalt mixtures prepared using the dry process. This study used crushed granite aggregate with the nominal maximum aggregate size of 14 mm whereas the shredded plastic bag is in the range of 5–10 mm. Quantitative sieving analysis and performance tests were carried out to examine the effects of plastic waste added into the asphalt mixture. The volumetric and performance properties combined with image analysis of the modified mixtures were obtained and compared with the control mixture. In addition, the moisture damage, resilient modulus, creep deformation and rutting were evaluated. This study also highlighted in detail the distribution of plastic particles in the final skeleton of the asphalt mixture. Based on the analysis, an enhanced dry process of mixing procedure was proposed and evaluated. Results showed that the addition of plastic particles using the conventional dry process leads to the deviation in the aggregate structure as high plastic content is added. Furthermore, the enhanced dry process developed in this study presents substantial enhancement in the asphalt performance, particularly with plastic waste that accounts for 20% of the weight of the asphalt binder.

scholarly journals Development of a 4.75 mm asphalt mixture design for Implementation in Louisiana DOTD Specifications

2020 ◽  
Vol 13 (6) ◽  
pp. 637-644
Author(s):  
Saman Salari ◽  
Samuel Cooper ◽  
Louay N. Mohammad ◽  
Peyman Barghabany
Keyword(s):  
Comprehensive Evaluation ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Performance Testing ◽  
Aggregate Size ◽  
Asphalt Mixtures ◽  
Maximum Aggregate Size ◽  
Construction Costs ◽  
The Cost ◽  
Wheel Tracking

AbstractThe Louisiana Department of Transportation and Development (DOTD) and other state agencies are continuously looking for techniques to reduce roadway maintenance and construction costs. A common consideration is to introduce asphalt mixtures with a smaller nominal maximum aggregate size (NMAS) for utilization in roadways. In a previous study, DOTD concluded that mixtures with a 4.75 mm NMAS provided acceptable performance as a surface layer. Excessive stockpiles of unused smaller aggregates can result in an economically competitive source to be consi dered for asphalt mixtures. The DOTD developed mixtures with four aggregate types and two binder types. A comprehensive evaluation of performance was conducted through volumetric and mechanistic testing. Performance testing consisted of the Loaded Wheel Tracking (LWT) test to determine rutting resistance, Semi-Circular Bend (SCB) test to evaluate intermediate temperature cracking resistance, and dynamic modulus (E*) to ascertain the stiffness at intermediate temperatures. As expected, asphalt binder grade, aggregate type and mixture composition affected the performance of mixtures evaluated. Gravel mixtures were susceptible to cracking, while limestone mixtures were susceptible to rutting. An economic analysis was conducted to determine the viability of 4.75 mm mixtures. The cost per ton of 4.75 mm mixtures in Louisiana was higher than conventional 12.5 mm mixtures. However, when considering the lift thickness of potential overlays, the 4.75 mm aggregate mixtures became more viable. Further, a life-cycle analysis of a designed pavement using AASHTO Pavement-ME was performed to compare the lifetime durability of the 4.75 mm NMAS mixtures to a conventional 12.5 mm mixture.

A Hybrid Model to Predict the Gyratory Compaction of Hot Mixed Asphalt

2019 ◽  
Author(s):  
Teng Man
Keyword(s):  
Hybrid Model ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Asphalt Mixtures ◽  
Compaction Process ◽  
Particle Rearrangement ◽  
Compaction Behavior ◽  
Grain Size Distributions ◽  
Gyratory Compaction

The compaction of asphalt mixture is crucial to the mechanical properties and the maintenance of the pavement. However, the mix design, which based on the compaction properties, remains largely on empirical data. We found difficulties to relate the aggregate size distribution and the asphalt binder properties to the compaction behavior in both the field and laboratory compaction of asphalt mixtures. In this paper, we would like to propose a simple hybrid model to predict the compaction of asphalt mixtures. In this model, we divided the compaction process into two mechanisms: (i) visco-plastic deformation of an ordered thickly-coated granular assembly, and (ii) the transition from an ordered system to a disordered system due to particle rearrangement. This model could take into account both the viscous properties of the asphalt binder and grain size distributions of the aggregates. Additionally, we suggest to use the discrete element method to understand the particle rearrangement during the compaction process. This model is calibrated based on the SuperPave gyratory compaction tests in the pavement lab. In the end, we compared the model results to experimental data to show that this model prediction had a good agreement with the experiments, thus, had great potentials to be implemented to improve the design of asphalt mixtures.

scholarly journals MECHANICAL PERFORMANCE OF ASPHALT MIXTURE CONTAINING CUP LUMP RUBBER

2019 ◽  
Vol 81 (6) ◽  
Author(s):  
Norfazira Mohd Azahar ◽  
Norhidayah Abdul Hassan ◽  
Ramadhansyah Putra Jaya ◽  
Hasanan Md. Nor ◽  
Mohd Khairul Idham Mohd Satar ◽  
...  
Keyword(s):  
Mechanical Performance ◽  
Resilient Modulus ◽  
Permanent Deformation ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Modified Asphalt ◽  
Dynamic Creep ◽  
Aging Conditions ◽  
Public Work Department ◽  
Indirect Tensile

The use of cup lump rubber as an additive in asphalt binder has recently become the main interest of the paving industry. The innovation helps to increase the natural rubber consumption and stabilize the rubber price. This study evaluates the mechanical performance of cup lump rubber modified asphalt (CMA) mixture in terms of resilient modulus, dynamic creep and indirect tensile strength under aging conditions. The CMA mixture was prepared using dense-graded Marshall-designed mix and the observed behavior was compared with that of conventional mixture. From the results, both mixtures passed the volumetric properties as accordance to Malaysian Public Work Department (PWD) specification. The addition of cup lump rubber provides better resistance against permanent deformation through the enhanced properties of resilient modulus and dynamic creep. Furthermore, the resilient modulus of CMA mixture performed better under aging conditions.  

Effect of Coarse Aggregate Morphology on the Resilient Modulus of Hot-Mix Asphalt

2005 ◽  
Vol 1929 (1) ◽  
pp. 1-9 ◽  
Author(s):  
Tongyan Pan ◽  
Erol Tutumluer ◽  
Samuel H. Carpenter
Keyword(s):  
Surface Texture ◽  
Coarse Aggregate ◽  
Resilient Modulus ◽  
Asphalt Binder ◽  
Aggregate Size ◽  
Asphalt Mixtures ◽  
Maximum Aggregate Size ◽  
Asphalt Mixes ◽  
Aggregate Morphology ◽  
The Relationship

The resilient modulus measured in the indirect tensile mode according to ASTM D 4123 reflects effectively the elastic properties of asphalt mixtures under repeated load. The coarse aggregate morphology quantified by angularity and surface texture properties affects resilient modulus of asphalt mixes; however, the relationship is not yet well understood because of the lack of quantitative measurement of coarse aggregate morphology. This paper presents findings of a laboratory study aimed at investigating the effects of the material properties of the major component on the resilient modulus of asphalt mixes, with the coarse aggregate morphology considered as the principal factor. With modulus tests performed at a temperature of 25°C, using coarse aggregates with more irregular morphologies substantially improved the resilient modulus of asphalt mixtures. An imaging-based angularity index was found to be more closely related to the resilient modulus than an imaging-based surface texture index, as indicated by a higher value of the correlation coefficient. The stiffness of the asphalt binder also had a strong influence on modulus. When the resilient modulus data were grouped on the basis of binder stiffnesses, the agreement between the coarse aggregate morphology and the resilient modulus was significantly improved in each group. Although the changes in aggregate gradation did not significantly affect the relationship between the coarse aggregate morphology and the resilient modulus, decreasing the nominal maximum aggregate size from 19 mm to 9.5 mm indicated an increasing positive influence of aggregate morphology on the resilient modulus of asphalt mixes.

Sign in / Sign up

Export Citation Format

Share Document