COMPARATIVE STUDY OF MATERIAL REMOVAL RATE AND TOOL WEAR RATE OF COPPER AND ALUMINIUM ON DIE SINKING EDM

2015 ◽  
Vol 77 (21) ◽  
Author(s):  
Maidin S. ◽  
H.H. El Grour ◽  
Seeying C.
Keyword(s):  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Copper Electrode ◽  
Machining Process ◽  
Work Piece ◽  
Small Depth ◽  
Pulse On Time ◽  
Pulse Off Time

The electrical discharge machining (EDM) is one of non - conventional machining process where the erosion of the work piece take place based on the thermal energy between the electrode and the work piece. Due to the widely used and its availability, copper and aluminium was used in this study. These two materials was machined using die sinking EDM to study the characteristics of each material using copper electrode. Few research has been conducted to study copper electrode to machined copper work piece and this was considered as a challenge in this research. More heat was generated and more time consumed was the reason behind machining small depth in this research. The important factors such as discharge current, voltage, pulse on time and pulse off time monitored and recorded to know how these factors effect on the Material Removal Rate (MRR) and Tool Wear Ratio (TWR) of the copper and aluminium work piece material. The experiments conducted under the designed full factorial procedure where pulse on-time and pulse current are used as the input parameters. It was found that material MRR increases with increase in current and pulse duration, but MRR is higher during machining of aluminum than that of copper. In term of TWR it is found that the TWR resulting of machining copper is lower than aluminium

Influence of Process Parameters on Characteristics of Electrical Discharge Machining of PH17-4 Stainless Steel

2015 ◽  
Vol 14 (03) ◽  
pp. 189-202 ◽  
Author(s):  
V. Vikram Reddy ◽  
P. Madar Valli ◽  
A. Kumar ◽  
Ch. Sridhar Reddy
Keyword(s):  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Hardness ◽  
Machining Process ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

In the present work, an investigation has been made into the electrical discharge machining process during machining of precipitation hardening stainless steel PH17-4. Taguchi method is used to formulate the experimental layout, to analyze the effect of each process parameter on machining characteristics and to predict the optimal choice for each electrical discharge machining process parameters namely, peak current, pulse on time and pulse off time that give up optimal process performance characteristics such as material removal rate, surface roughness, tool wear rate and surface hardness. To identify the significance of parameters on measured response, the analysis of variance has been done. It is found that parameters peak current and pulse on time have the significant affect on material removal rate, surface roughness, tool wear rate and surface hardness. However, parameter pulse off time has significant affect on material removal rate. Confirmation tests are conducted at their respective optimum parametric settings to verify the predicted optimal values of performance characteristics.

Effects of Process Parameters on Material Removal Rate and Surface Roughness in Wedm of H-13 Die Tool Steel

2018 ◽  
Vol 28 ◽  
pp. 55-66 ◽  
Author(s):  
Kuldeep Singh ◽  
Khushdeep Goyal ◽  
Deepak Kumar Goyal
Keyword(s):  
Surface Roughness ◽  
Taguchi Method ◽  
Tool Steel ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Pulse On Time ◽  
Pulse Off Time

In research work variation of cutting performance with pulse on time, pulse off time, wire type, and peak current were experimentally investigated in wire electric discharge machining (WEDM) process. Soft brass wire and zinc coated diffused wire with 0.25 mm diameter and Die tool steel H-13 with 155 mm× 70 mm×14 mm dimensions were used as tool and work materials in the experiments. Surface roughness and material removal rate (MRR) were considered as performance output in this study. Taguchi method was used for designing the experiments and optimal combination of WEDM parameters for proper machining of Die tool steel (H-13) to achieve better surface finish and material removal rate. In addition the most significant cutting parameter is determined by using analysis of variance (ANOVA). Keywords Machining, Process Parameters, Material removal rate, Surface roughness, Taguchi method

Performance Measurement and Data Analysis of Material Removal Rate for Wire Cut Electro Discharge Machining Process

2011 ◽  
Vol 110-116 ◽  
pp. 1683-1690 ◽  
Author(s):  
Vishal Parashar ◽  
A. Rehman ◽  
J.L. Bhagoria
Keyword(s):  
Regression Analysis ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Performance Criteria ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Dielectric Flushing

In this paper, statistical and regression analysis of material removal rate using design of experiments is proposed for WEDM operations. Experimentation was planned as per Taguchi’s mixed orthogonal array. Each experiment has been performed under different cutting conditions of gap voltage, pulse ON time, pulse OFF time, wire feed and dielectric flushing pressure. Stainless Steel grade 304L was selected as a work material to conduct the experiments. From experimental results, the material removal rate was determined for each machining performance criteria. Analysis of variance (ANOVA) technique was used to find out the variables affecting the material removal rate. Assumptions of ANOVA were discussed and carefully examined using analysis of residuals. Variation of the material removal rate with machining parameters was mathematically modeled by using the regression analysis method. The developed model was validated with a set of experimental data and appeared to be satisfactory. Signal to noise ratio was applied to measure the performance characteristics deviating from the actual value. Finally, experimental confirmation was carried out to identify the effectiveness of this proposed method.

scholarly journals The Methodologies Adopted To Improve the Machinability in Die-Sinking EDM

2019 ◽  
Vol 9 (1S4) ◽  
pp. 645-647
Keyword(s):  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
High Surface ◽  
High Hardness ◽  
Machining Process ◽  
Work Piece ◽  
Machining Processes

Electrical discharge machining (EDM) is one of the oldest nontraditional machining processes, commonly used in automotive, aerospace and ship building industries for machining metals that have high hardness, strength and to make complicated shapes that cannot be produced by traditional machining techniques. The process is based on the thermoelectric energy between the work piece and an electrode. EDM is slow compared to conventional machining, low material removal rate, high surface roughness, high tool wear and formation of recast layer are the main disadvantages of the process. Tool wear rate, material removal rate and surface quality are important performance measures in electric discharge machining process. Numbers of ways are explored by researchers for improving and optimizing the output responses of EDM process. The paper summarizes the research on die-sinking EDM relating to the improvements in the output response.

Influence of Process Parameters on Material Removal Rate in Electrical Discharge Machining Cylindrical Shaped Parts

2021 ◽  
Vol 1018 ◽  
pp. 91-95
Author(s):  
Tran Thi Hong ◽  
Nguyen Hong Linh ◽  
Bui Thanh Danh ◽  
Le Hong Ky ◽  
Vu Thi Lien ◽  
...  
Keyword(s):  
Material Removal Rate ◽  
Material Removal ◽  
Pulse Current ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Work Piece ◽  
Influence Of Process Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
The Impact

This paper aims to find the impact of Electric Discharge Machining (EDM) factors on material removal rate (MRR) for 90CrSi alloy steel. Five three-level factors including pulse on time (Ton), pulse off time (Toff), pulse current (IP), server voltage (SV), and diameter of work-piece (dw) are investigated to explore their contribution on MRR by using Taguchi method in twenty-seven experiments based on an orthogonal array L27 (35). The findings realize that MRR is the most affected by the pulse current while the effect of the dw is the smallest. Based on ANOVA analysis, an optimal model of MRR has been developed and verified by comparing with the experiment result. The applicability of this proposed method can be used for further studies in EDM process.

Modelling of Material Removal Rate in EDM of Nonconductive ZrO2 Ceramic by Taguchi Method

2013 ◽  
Vol 393 ◽  
pp. 246-252 ◽  
Author(s):  
A. Sabur ◽  
Mohammad Yeakub Ali ◽  
M.A. Maleque
Keyword(s):  
Taguchi Method ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Pyrolytic Carbon ◽  
Carbon Layer ◽  
Machining Process ◽  
Machined Surface ◽  
Pulse On Time ◽  
Pulse Off Time

Electro discharge machining (EDM) technique, a noncontact machining process, is applied for structuring nonconductive ZrO2 ceramic. A conductive layer of adhesive copper is applied on the workpiece surface to initiate the sparks. Kerosene is used as dielectric for creation of continuous conductive pyrolytic carbon layer on the machined surface. Experiments are conducted by varying the peak current (Ip), pulse-on time (Ton), pulse-off time (Toff) and gap voltage (Vg). Correlating these variables a mathematical model for material removal rate (MRR) is developed using Taguchi method. The optimized parametric conditions are determined for higher MRR through ANOVA and signal to noise (S/N) ratio analysis. The results showed that the Ip and Ton are the significant parameters of MRR in EDM for nonconductive ZrO2 ceramic. The model also showed that MRR increases with the increase of Ip and Ton, but the process is controlled by Ip as a whole.

scholarly journals Surface and Subsurface Quality of Titanium Grade 23 Machined by Electro Discharge Machining

Materials ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 164
Author(s):  
Panagiotis Karmiris-Obratański ◽  
Emmanouil L. Papazoglou ◽  
Beata Leszczyńska-Madej ◽  
Krzysztof Zagórski ◽  
Angelos P. Markopoulos
Keyword(s):  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
White Layer ◽  
Tool Material ◽  
Machining Process ◽  
Machining Performance ◽  
Pulse On Time

Electrical Discharge Machining (EDM) is a non-traditional cutting technology that is extensively utilized in contemporary industry, particularly for machining difficult-to-cut materials. EDM may be used to create complicated forms and geometries with great dimensional precision. Titanium alloys are widely used in high-end applications owing to their unique intrinsic characteristics. Nonetheless, they have low machinability. The current paper includes an experimental examination of EDM’s Ti-6Al-4V ELI (Extra Low Interstitials through controlled interstitial element levels) process utilizing a graphite electrode. The pulse-on current (IP) and pulse-on time (Ton) were used as control parameters, and machining performance was measured in terms of Material Removal Rate (MRR), Tool Material Removal Rate (TMRR), and Tool Wear Ratio (TWR). The Surface Roughness (SR) was estimated based on the mean roughness (SRa) and maximum peak to valley height (SRz), while, the EDMed surfaces were also examined using optical and SEM microscopy and cross-sections to determine the Average White Layer Thickness (AWLT). Finally, for the indices above, Analysis of Variance (ANOVA) was conducted, whilst semi-empirical correlations for the MRR and TMRR were given using the Response Surface Method (RSM). The results show that the pulse-on time is the most significant parameter of the machining process that may increase the MRR up to 354%. Pulse-on current and pulse-on time are shown to have an impact on the surface integrity of the finished product. Furthermore, statistics, SEM, and EDX images on material removal efficiency and tool wear rate are offered to support the core causes of surface and sub-surface damage. The average microhardness of the White Layer (WL) is 1786 HV.

scholarly journals Machine Ability Characteristics of PWEDM Process

2019 ◽  
Vol 9 (1) ◽  
pp. 3580-3583
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Electrical Discharge Machine ◽  
Machining Process ◽  
Work Piece ◽  
Tool Wear Rate

The traditional machining consists of a specific contact between the tool and work piece. As a result of this contact the tool may wear out after a few operations. In addition to that, the MRR (Material Removal Rate), Surface Finish, etc. is also lowered. As a result of these drawbacks, traditional or conventional machining processes cannot be used to machine ceramic based alloys and thus we opt for unconventional machining process. The Electrical Discharge Machine contains of two spaces one is Electrode and other is Work piece. In this concept the among the tool wear rate is moderate and the surface roughness is to be poor. The tool cost is so high. Hence continuously tool modification is not possible. So in the work main objective of the problem is reduced the tool wear rate and increase the MRR. (Material removal rate). So in the case we are consider in the surface roughness. The surface roughness is to be high is the taken in industrial application. So we have focus with surface roughness. These are the considering with in our problems. In our aim is reducing the toll wear and improve the Material Remove rate. In order to addition of graphite in Electrolyte. When added the electrolyte in Graphite the Toll wear rate decrease and increase a material Removal Rate. Finally we have disc the DOE process

Enhancement of EDM Performance by Using Copper-Silver Composite Electrode

2020 ◽  
Vol 38 (9A) ◽  
pp. 1352-1358
Author(s):  
Saad K. Shather ◽  
Abbas A. Ibrahim ◽  
Zainab H. Mohsein ◽  
Omar H. Hassoon
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Composite Electrode ◽  
Removal Rate ◽  
Pure Copper ◽  
High Speed Steel ◽  
Pulse On Time ◽  
Pulse Off Time

Discharge Machining is a non-traditional machining technique and usually applied for hard metals and complex shapes that difficult to machining in the traditional cutting process. This process depends on different parameters that can affect the material removal rate and surface roughness. The electrode material is one of the important parameters in Electro –Discharge Machining (EDM). In this paper, the experimental work carried out by using a composite material electrode and the workpiece material from a high-speed steel plate. The cutting conditions: current (10 Amps, 12 Amps, 14 Amps), pulse on time (100 µs, 150 µs, 200 µs), pulse off time 25 µs, casting technique has been carried out to prepare the composite electrodes copper-sliver. The experimental results showed that Copper-Sliver (weight ratio70:30) gives better results than commonly electrode copper, Material Removal Rate (MRR) Copper-Sliver composite electrode reach to 0.225 gm/min higher than the pure Copper electrode. The lower value of the tool wear rate achieved with the composite electrode is 0.0001 gm/min. The surface roughness of the workpiece improved with a composite electrode compared with the pure electrode.

scholarly journals Multi- Response Optimization of Wire EDM Process Parameter on Aluminium Alloy (5086)

2020 ◽  
Vol 10 (1) ◽  
pp. 224-229
Keyword(s):  
Aluminium Alloy ◽  
Material Removal Rate ◽  
Material Removal ◽  
Control Parameter ◽  
Removal Rate ◽  
Response Optimization ◽  
High Pulse ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

In the present work, the effect of process parameters on material removal rate during the machining of aluminium alloy (5086) with WEDM is studied. The four control parameter were selected i.e pulse on time (TON), pulse off time (TOFF), peak current (IP), and spark gap voltage (SV) to investigate their effects on material removal rate (MRR). Each control parameter had three levels. Total 27 experiments were done with a zinc coated brass wire of diameter 0.25 mm. Taguchi L9 orthogonal array technique was used for the experiment. ANOVA was used to find out the significance of control parameters and their contribution on MRR. It was found that maximum material removal rate was 41.52 mm3 /min which was due to high pulse on time and low pulse off time.

Sign in / Sign up

Export Citation Format

Share Document