Parametric Study of Compound Cold-Formed Steel Sections as Flexural Members

2015 ◽  
Vol 74 (4) ◽  
Author(s):  
Ker Shin Mu ◽  
Poi Ngian Shek ◽  
Arizu Sulaiman ◽  
Boon Cheik Tan
Keyword(s):  
Parametric Study ◽  
Local Buckling ◽  
Bending Moment ◽  
Steel Plates ◽  
Pure Bending ◽  
Moment Capacity ◽  
Flexural Members ◽  
Bending Capacity ◽  
Steel Sections ◽  
Cold Formed Steel

This paper presents a parametric study on compound cold-formed steel sections as flexural members. The compound members are used to sustain higher load and solve the problems of local buckling and lateral torsional buckling. The aim of this study is to investigate the strength of compound cold-formed steel section subjected to pure bending. Moment capacity of the compound section is calculated in accordance to Eurocode 3. The compound cold-formed steel sections proposed in this study are made up of two cold-formed steel C-section and hot-rolled plates. Steel plates with thickness of 3 mm to 8 mm are added to the cold-formed double C-section with the purpose to increase the bending capacity. From the comparison, moment capacity of compound sections give higher value as compared to cold-formed steel C-section with the comparison ratios range between 1.15 and 3.30. Results from the study show that compound cold-formed steel sections able to enhance the strength in resisting pure bending by adding steel plate at the flanges and web of the section. On the other hand, finite element modeling using ANSYS is carried out on two of the selected compound cold-formed steel sections and the results show good agreement with analytical results.

Experimental Investigation on Cold-formed Steel Beams under Pure Bending

2012 ◽  
pp. 13-20 ◽  
Author(s):  
Yeong Huei Lee ◽  
Yee Ling Lee ◽  
Cher Siang Tan
Keyword(s):  
Local Buckling ◽  
Bending Moment ◽  
Steel Beams ◽  
Pure Bending ◽  
Lateral Instability ◽  
Moment Capacity ◽  
British Standard ◽  
Cold Formed Steel ◽  
The Moment ◽  
Design Yield

This paper presents the flexural behaviour of cold-formed double lipped channels beams under pure bending action. Two channel sections are bolted back-to-back to form an I-shape structural beam member. A series of six experiment tests were carried out on beam specimens DC200 and DC250, each with 200 mm depth and 250 mm depth respectively. The thickness of beam section is 2 mm and the design yield strength is 350 N/mm2. All beams failed at local buckling at top-flange due to lateral instability of the cold-formed steel structural members. The moment resistance for DC200 is 17.87 kNm and DC250 is 31.53 kNm. The experimental results are compared to theoretical resistance prediction based on British Standard and Eurocode. The comparison showed that the experimental moment capacity is lower than the theoretical bending moment resistance but higher than theoretical buckling moment resistance from Eurocode. This showed that a better agreement is achieved between experimental data and Eurocode buckling moment resistance for cold-formed steel beam under pure bending. Kertas kerja ini membentangkan sifat lenturan rasuk keluli tergelek sejuk di bawah tindakan lenturan tulen. Dua channel dihimpunkan berkembar dan diperketatkan dengan bolt untuk membentuk rasuk struktur bentuk-I. Satu siri ujian lenturan telah dijalankan ke atas spesimen rasuk DC200 dan DC250, dengan kedalaman 200 mm dan 250 mm masing-masing. Ketebalan keratan rasuk adalah 2 mm dan kekuatan reka bentuk adalah 350 N/mm2. Semua rasuk gagal pada momen kilasan sisi di bahagian atas bebibir akibat ketakstabilan sisi anggota keluli tergelek sejuk. Rintangan momen bagi DC200 adalah 17.87 kNm dan DC250 adalah 31.53 kNm. Keputusan eksperimen dibanding dengan ramalan teori yang berdasarkan British Standard dan Eurocodes. Perbandingan tersebut menunjukkan bahawa rintangan momen lenturan eksperimen adalah lebih rendah daripada ramalan teori momen lenturan tetapi lebih tinggi daripada ramalan teori momen rintangan kilasan sisi mengikut Eurocode. Ini menunjukkan bahawa persetujuan baik dicapai di antara keputusan eksperimen dengan ramalan teori Eurocode momen rintangan kilasan sisi bagi rasuk keluli tergelek sejuk.

Bending Capacity of Girth-Welded Pipes

2005 ◽  
Author(s):  
Enrico Torselletti ◽  
Luigino Vitali ◽  
Roberto Bruschi
Keyword(s):  
Longitudinal Strain ◽  
Local Buckling ◽  
Bending Moment ◽  
Experimental Tests ◽  
Reduction Factor ◽  
Fe Model ◽  
Moment Capacity ◽  
3 Dimensional ◽  
Bending Capacity ◽  
Pipe Bending

In the last ten years, several studies were completed with the aim to define a design format for the local buckling of pipes subjected to differential pressure, axial load and bending moment. Experimental tests were carried out and simplified analytical solutions were developed in order to predict the pipe bending moment capacity and the associated level of deformation. Standard finite element (FE) structural codes, such as ABAQUS, ADINA, ANSYS, etc., were and are used as a “numerical testing laboratory”, where the model is suitably calibrated to few experimental tests. The outcomes of these research efforts were implemented in the design equations enclosed in international design rules, as DNV OS-F101. The local buckling design formats, included in these rules, give the limit bending moment and associated longitudinal strain as a function of the relevant parameters. The effect of the girth weld is introduced with a reduction factor only for what regards the strain at limit bending moment. This paper addresses the effects of the presence of the girth weld on both limit bending moment and corresponding compressive longitudinal strain. A 3-dimensional (3D) FE model developed in ABAQUS has been developed to perform a parametric analysis. The FE model results are shown to compare reasonably well with full scale experiments performed for on-shore pipelines. The limit bending moment is reduced by the weld misalignment and this reduction is also dependent on both internal pressure load and linepipe material mechanical strength. The FE results are compared with the limit bending moment calculated with DNV OS-F101.

Experimental Study of Cold-Formed Steel Moment Connections with Screw Fasteners

2019 ◽  
Vol 950 ◽  
pp. 85-89
Author(s):  
Adeline Ling Ying Ng ◽  
Zhi Yong Law
Keyword(s):  
Local Buckling ◽  
Test Results ◽  
Moment Connections ◽  
Moment Capacity ◽  
Moment Connection ◽  
Steel Moment Connection ◽  
Steel Sections ◽  
Cold Formed Steel ◽  
The Moment ◽  
Hot Rolled

A series of connection with screw fasteners were tested to study the behavior of cold-formed steel moment connection. The test specimens included hot-rolled parallel flange channels, cold-formed lipped C-Channels, and self-drilling self-fastening screws. Two different lipped C-Channels and a various number of screws per connection were used in this study. The moment-rotation behavior, rotational rigidity, and the connection capacity differed with the number of screws. The connection behaved as a pinned connection when 4 screws were used. However, local buckling was observed in the cold-formed steel sections near the connection when 8, 10 and 14 screws were used. The connection test results were compared with theoretical results calculated in accordance to the Australian Standards. None of the connection tested could achieve the moment capacity of the section connected.

Flexural Tests on the H-Section Simple Beams with Local Buckling

2011 ◽  
Vol 105-107 ◽  
pp. 1677-1680
Author(s):  
Young Bong Kwon ◽  
Jin Hwan Cheung ◽  
Byung Seung Kong ◽  
Hwan Woo Lee ◽  
Kwang Kyu Choi
Keyword(s):  
Local Buckling ◽  
Bending Moment ◽  
Lateral Torsional Buckling ◽  
Torsional Buckling ◽  
Moment Capacity ◽  
Flexural Members ◽  
Negative Effect ◽  
Large Width ◽  
The Moment ◽  
Flexural Tests

This paper describes a series of flexural tests conducted on the H-section beams fabricated from SM490 plate of thickness 0.6mm with nominal yield stress 315 MPa. Flexural members with large width-to-thickness ratios in the flanges or the web may undergo local buckling before lateral-torsional buckling. The local buckling has a negative effect on the moment capacity based on the lateral-torsional buckling. Simple bending moment capacity formulas for flexural members were calibrated to the test results to account for interaction between local buckling and lateral-torsional buckling. The ultimate flexural strengths predicted by the proposed formulas for direct strength method were compared with the AISC (2005) and Eurocode3 (2003). The comparison showed that the moment formulas proposed can predict conservatively the bending moment capacity of H-section flexural members with local buckling.

Built-Up Cold-Formed Steel Beams with Corrugated Webs Connected with Spot Welding

2015 ◽  
Vol 1111 ◽  
pp. 157-162 ◽  
Author(s):  
Ştefan Benzar ◽  
Viorel Ungureanu ◽  
Dan Dubină ◽  
Mircea Burcă
Keyword(s):  
Spot Welding ◽  
Local Buckling ◽  
Steel Beams ◽  
Steel Buildings ◽  
Moment Capacity ◽  
Steel Sheets ◽  
Beam Depth ◽  
Steel Sections ◽  
Cold Formed Steel ◽  
The Web

Corrugated web girders emerged in the past two decades. Their main advantages consists in the possibility to use slender webs avoiding the risk of premature local buckling. Consequently, higher moment capacity might be obtained increasing the beam depth with really thin webs, which are stiffened by the corrugations. Increased interest for this solution was observed for the main frames of single-storey steel buildings and steel bridges. A new solution was proposed at the Politehnica University of Timisoara, in which the beam is composed by a web of trapezoidal steel sheet and flanges of back-to-back lipped channel steel sections. This solution uses self-drilling screws for connecting flanges to the web and to ensure the continuity of the web as seam fasteners. Starting from this new technological solution the paper extends and investigates the use of spot welding as seam fastening to build the web, in order to increase the degree of automation of fabrication. Experimental work of specimens in shear having two or three layers of steel sheets connected by spot welding will be presented. The results will be implemented on a numerical model in order to study the behaviour of the beams presented above.

Local buckling capacity of C-shaped cold-formed steel sections with punched webs

1984 ◽  
Vol 11 (1) ◽  
pp. 1-7 ◽  
Author(s):  
Robert Loov
Keyword(s):  
Local Buckling ◽  
Effective Width ◽  
Test Results ◽  
Average Yield ◽  
Steel Sections ◽  
Load Tests ◽  
Cold Formed Steel ◽  
Stub Column ◽  
Best Fit ◽  
The Web

Load tests were carried out on 36 stub column samples of cold-formed steel studs having 38.1 mm wide × 44.5 mm long holes punched through their webs, steel thicknesses of 1.21–2.01 mm, and overall section depths of 63–204 mm. Based on these tests a best-fit equation for the effective width of the unstiffened portion of the web beside the holes has been developed. Suggested design equations have been proposed. The test results support the present equation for the average yield stress [Formula: see text] in Canadian Standards Association Standard S136-1974 but the present code equations for unstiffened plates are unduly conservative when applied to the design of the web adjacent to openings of the size considered.

scholarly journals Experimental Test of Circular Hollow Sections Solid Flanged Splice

2020 ◽  
Vol 8 (6) ◽  
pp. 3847-3851
Keyword(s):  
Finite Element ◽  
Bending Moment ◽  
Finite Element Models ◽  
Moment Capacity ◽  
Flexural Members ◽  
End Plate ◽  
Modes Of Failure ◽  
Aesthetic Appearance ◽  
Bolt Failure ◽  
Ultimate Moment

The use of circular hollow sections (CHS) have increased due to its aesthetic appearance and good mechanical properties. This research investigates the behavior of the bolted CHS splices with circular end plates under pure bending moment that allows the use of CHS as long flexural members. Three connections are tested and the corresponding finite element models are constructed. The finite element models are verified with the experimental results and showed acceptable agreement in terms of both ultimate moment capacity and load-displacement curves. Three modes of failure are observed where the first is pure bolt failure, the second is pure end plate yielding while the third is a combination of the two modes where end plate plastifies accompanied by bolt failure. Stiffness is also observed and is found to be greatly affected by the thickness of the end plate

Material Property Effects on Critical Buckling Strains in Energy Pipelines

2002 ◽  
Author(s):  
Alfred B. Dorey ◽  
David W. Murray ◽  
J. J. Roger Cheng
Keyword(s):  
Material Property ◽  
Parametric Study ◽  
Numerical Models ◽  
Local Buckling ◽  
Analytical Models ◽  
Basic Material ◽  
Line Pipe ◽  
Moment Capacity ◽  
Yield Plateau ◽  
Critical Buckling Strain

Investigations in the development of a predictive critical buckling strain equation have shown that the grade of the material is one of five fundamental non-dimensional parameters in determining the critical local buckling strain for line pipe under combined loads. Further to this, the shape of the material curve also plays a significant role in the resulting critical buckling strain. Over 50 full-scale test specimens have been tested at the University of Alberta and effective numerical finite element analytical models have been developed. A parametric study consisting of 170 analyses was performed using the numerical models and critical buckling strain equations were derived. One of the essential variables in the new equations is a function of the specimen’s material properties. The results indicate that the higher the grade of the material the lower the value of the critical buckling strain. Furthermore, the level of agreement between the new equations and the experimental data was found to be dependent on the shape of the material curve for the specimen. Experimentally, two basic material curve shapes were observed, namely: specimens with a “rounded” material curve through the yield strength and specimens with a material property that exhibited a distinct “yield plateau” or yield point. Comparison of the experimental and numeric data showed that the specimens that were fabricated from material with a distinct yield plateau had different critical buckling strains when compared to specimens tested with rounded material curves. A subsequent parametric study was undertaken to examine the effect that the different shaped material curves had on the local and global behaviour. The results of this subsidiary parametric study showed that the global moment capacity was essentially independent of the shape of the material curve (the ratio of the peak moment from the yield plateau material to the peak moment for the rounded material was 1.018). However, the local critical buckling strain was significantly lower for the specimens analyzed with the material that had the yield plateau (the ratio of the critical strains for the two different material curves was 0.710).

Study of Bending Capacity of an HPHT CRA-Lined Seamless Pipeline

2014 ◽  
Author(s):  
Cyprian Gil ◽  
Knut Tørnes ◽  
Per Damsleth
Keyword(s):  
Internal Pressure ◽  
Strain Localization ◽  
Local Buckling ◽  
Bending Moment ◽  
Design Criteria ◽  
Design Codes ◽  
Moment Capacity ◽  
Wide Range ◽  
Global Buckling ◽  
The Moment

A study has been performed to better understand ultimate bending moment and strain capacities of pipelines in relation to criteria defined in the design codes. An 18″ HPHT flowline was designed to undergo global buckling on uneven seabed and to resist trawl gear interference. The high temperature (155 degC) and pressure (300 bar) posed considerable design challenges for material selection and design criteria. A CRA-lined X60 CMn pipeline was selected for the project. The pipeline was of seamless manufacture for which the stress/strain characteristics are subject to the effect of Lüders bands. The DNV-OS-F101 code covers a wide range of D/t but does not specifically address Lüder’s material behaviour which could significantly reduce the bending moment capacity of pipe. The global buckling and trawl pull-over FE analysis results indicated the pipe was highly utilized, requiring excessive amounts of seabed intervention at great cost to meet the DNV LCC criteria. Detailed FE simulation of limit states for local buckling and strain localization of a 3D solid element pipe model was performed, with both Roundhouse and Lüders material properties, to investigate pipe capacity in relation to that stipulated by the design codes. The pipe moment capacity was established by obtaining the moment curvature relationship by bending the local pipe section subject to internal pressure until the maximum resistance was reached. Imperfections were introduced to initiate local buckling at the desired location. To determine strain concentration factors and strain localization, the effects of thickness changes and weld misalignment were also studied. The DNV OS-F101 LCC moment criterion formulation computes a decreasing moment capacity for increasing internal pressure. It has been suggested in the literature that this is correct for higher D/t but the criterion may be conservative for pipes with lower D/t. The combination of Lüders material with low D/t is not specifically addressed by any design code. Clarification of these aspects will provide a better understanding of the risk of failure for highly utilized seamless pipelines and allow for modified design criteria that will reduce seabed intervention costs. The results of the study showed that a higher bending moment criterion and associated strain criterion could be adopted for the design that allows for the higher initial strain caused by Lüder’s plateau. The ultimate bending moment capacity of low D/t pipe with Lüder’s material was found to be similar to that of Roundhouse material due to work hardening. In addition, it was demonstrated that the potential strength of the CRA liner could enhance the moment capacity of the seamless pipe.

Sign in / Sign up

Export Citation Format

Share Document