Investigation on Wear Behavior and Chip Formation During Up-Milling and Down-Milling Operations for Inconel 718

2014 ◽  
Vol 66 (3) ◽  
Author(s):  
M. A. Hadi ◽  
J. A. Ghani ◽  
C. H. Che Haron ◽  
M. S. Kasim
Keyword(s):  
Tool Wear ◽  
Chip Formation ◽  
Inconel 718 ◽  
End Milling ◽  
Wear Behavior ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Milling Operations ◽  
Milling Operation ◽  
Coated Carbide

A comprehensive study and FEM simulation of ball nose end milling on tool wear behavior and chip formation had been performed on Inconel 718 (nickle-based superalloy) under minimum quantity lubricant (MQL) condition. In this paper, the investigation was focusing on the comparison of up-milling and down-milling operations using a multi-layer TiAlN/AlCrN-coated carbide inserts. A various cutting parameters; depth of cut, feed rate and cutting speed were considered during the evaluation. The experimental results showed that down-milling operation has better results in terms of tool wear compared to up-milling operation. Chipping on cutting tool edge responsible to notch wear with prolong machining. It was observed that the chips formed in up-milling operation were segmented and continuous, meanwhile down-milling operation produced discontinuous type of chips.

Experimental Investigation on Tool Wear when End-Milling Inconel 718 with Coated Carbide Inserts

2011 ◽  
Vol 188 ◽  
pp. 410-415 ◽  
Author(s):  
Yuan Wei Wang ◽  
Jian Feng Li ◽  
Z.M. Li ◽  
Tong Chao Ding ◽  
Song Zhang
Keyword(s):  
Tool Wear ◽  
Inconel 718 ◽  
Flank Wear ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Radial Depth ◽  
Coated Carbide ◽  
Carbide Inserts

In this paper, some experiments were conducted to investigate tool wear when end-milling Inconel 718 with the TiAlN-TiN PVD coated carbide inserts. The worn tools were examined thoroughly under scanning electron microscope (SEM) with Energy Dispersive X-ray Spectroscopy and 3D digital microscope to expatiate tool wear morphologies and relevant mechanisms. The flank wear was uniformity in finishing milling process, and the average flank wear were selected as the criterion to study the effects of cutting parameters (cutting speed, feed per tooth, radial depth of cut, and axial depth of cut) on tool wear. Finally, the optimal combination of the cutting parameters for the desired tool life is obtained.

Optimisation of Machining Parameters for High Feed End Milling on Inconel 718 Super Alloy

2014 ◽  
Vol 592-594 ◽  
pp. 584-590 ◽  
Author(s):  
Vinay Varghese ◽  
K. Annamalai ◽  
K. Santhosh Kumar
Keyword(s):  
Inconel 718 ◽  
End Milling ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Milling Operation ◽  
High Feed ◽  
Grey Relational ◽  
Super Alloy

This study investigates about machining practices used worldwide for machining of Inconel 718 super alloy. The effect of machining parameters like cutting speed, feed and depth of cut on machining responses like surface roughness and material removal rate when end milling Inconel 718 is studied using nine trials carried out based on L9 orthogonal array. A Taguchi based grey relational analysis was used for optimisation of machining parameters for high feed end milling operation on Inconel 718. An analysis of variance (ANOVA) was used to find the most significant factor. Validation of results through confirmation tests was performed and experimental results show that surface quality and productivity can be improved efficiently with this approach.

Preheating in End Milling of AISI D2 Hardened Steel with Coated Carbide Inserts

2009 ◽  
Vol 83-86 ◽  
pp. 56-66 ◽  
Author(s):  
Mohd Amri Lajis ◽  
A.K.M. Nurul Amin ◽  
A.N. Mustafizul Karim ◽  
A.M.K. Hafiz
Keyword(s):  
Tool Wear ◽  
Surface Finish ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Inductive Heating ◽  
Machining Parameters ◽  
Aisi D2 ◽  
Coated Carbide

This study was conducted to investigate the effect of preheating through inductive heating mechanism in end milling of AISI D2 hardened steel (60-62 HRC) by using coated carbide tool inserts. Apart from preheating, two other machining parameters such as cutting speed and feed were varied while the depth of cut constant was kept constant. Tool wear phenomenon and machined surface finish were found to be significantly affected by preheating temperature and other two variables. End milling operation was performed on a Vertical Machining Centre (VMC). Preheating of the work material to a higher temperature range resulted in a noticeable reduction in tool wear rate leading to a longer tool life. In addition, improved surface finish was obtained with surface roughness values lower than 0.4 μm, leaving a possibility of skipping the grinding and polishing operations for certain applications.

The Effects of TiAlN and TiN Coating during End Milling of INCONEL 718

2014 ◽  
Vol 564 ◽  
pp. 566-571
Author(s):  
K. Kamdani ◽  
Sulaiman Hasan ◽  
Mohd Amri Lajis
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Feed Rate ◽  
Inconel 718 ◽  
End Milling ◽  
Cutting Speed ◽  
Extreme Condition ◽  
Carbide Tool ◽  
Coated Carbide Tool ◽  
Coated Carbide

Inconel 718 is a registered trademark of Special Metals Corporation that refers to a family of austenitic nickel-chromium-based super alloys. This material usually being used or operate in high temperature and extreme condition like aerospace industry, turbocharger rotors and seals. This research presents an experimental study of the cutting force variation, surface roughness, tool life and tool wear in end milling Inconel 718. The experimental results showed that flank wear was the predominant failure mode affecting tool life for TiAlN and TiN coated carbide tool. TiAlN is the better coated tool than TiN because it produce better surface finish and resultant force. Feed rate is one of the parameter that effecting results in this experiment. The higher feed rate will shorten the life of the tool. Although for the cutting condition, the situation is quite different where the proper cutting speed will maintain the tool life and tool wear for cutting tool. The overall study shows that TiAlN coated carbide tool with cutting speed 100 m/min, depth of cut 0.5 mm and feed rate 0.1 mm/tooth is the optimum parameter in this experiment.

Optimal Cutting Parameters for Desired Surface Roughness in End Milling Inconel 718

2010 ◽  
Vol 126-128 ◽  
pp. 911-916 ◽  
Author(s):  
Yuan Wei Wang ◽  
Song Zhang ◽  
Jian Feng Li ◽  
Tong Chao Ding
Keyword(s):  
Surface Roughness ◽  
Inconel 718 ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Radial Depth ◽  
Exponential Regression Model ◽  
Optimal Cutting Parameters ◽  
Coated Carbide

In this paper, Taguchi method was applied to design the cutting experiments when end milling Inconel 718 with the TiAlN-TiN coated carbide inserts. The signal-to-noise (S/N) ratio are employed to study the effects of cutting parameters (cutting speed, feed per tooth, radial depth of cut, and axial depth of cut) on surface roughness, and the optimal combination of the cutting parameters for the desired surface roughness is obtained. An exponential regression model for the surface roughness is formulated based on the experimental results. Finally, the verification tests show that surface roughness generated by the optimal cutting parameters is really the minimum value, and there is a good agreement between the predictive results and experimental measurements.

scholarly journals Content Comparative Investigation on Tool Wear During End Milling of AISI H13 Steel with Different Tool Path Strategies

2017 ◽  
Vol 6 (4) ◽  
pp. 327-333
Author(s):  
Erry Yulian T. Adesta ◽  
Muhammad Riza ◽  
Avicenna Avicenna
Keyword(s):  
Tool Wear ◽  
Experimental Work ◽  
Tool Path ◽  
End Milling ◽  
Cutting Speed ◽  
Comparative Investigation ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
H13 Steel ◽  
Coated Carbide

Tool wear prediction plays a significant role in machining industry for proper planning and control machining parameters and optimization of cutting conditions. This paper aims to investigate the effect of tool path strategies that are contour-in and zigzag tool path strategies applied on tool wear during pocket milling process. The experiments were carried out on CNC vertical machining centre by involving PVD coated carbide inserts. Cutting speed, feed rate and depth of cut were set to vary. In an experiment with three factors at three levels, Response Surface Method (RSM) design of experiment with a standard called Central Composite Design (CCD) was employed. Results obtained indicate that tool wear increases significantly at higher range of feed per tooth compared to cutting speed and depth of cut. This result of this experimental work is then proven statistically by developing empirical model. The prediction model for the response variable of tool wear for contour-in strategy developed in this research shows a good agreement with experimental work.

scholarly journals Influence of Cutting Parameters on Chatter and Tool Wear During End Milling of Stainless Steel Conducted on VMC

1970 ◽  
Vol 3 (2) ◽  
Author(s):  
A.K.M.N. AMIN, M. IMRAN AND M. ARIF
Keyword(s):  
Stainless Steel ◽  
Tool Wear ◽  
Surface Finish ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Wear Intensity ◽  
Depth Of Cut ◽  
Machined Surface ◽  
Milling Operation

Stainless steels are a group of difficult to machine work materials. The difficulty in machining stainless steels is manifested in high contact length and stresses, formation of serrated chips and development of chatter resulting in high tool wear rates and poor machined surface finish. The paper focuses on the performance of TiN coated-carbide inserts in machining stainless steel specimens in end milling operation performed on vertical machining centre (VMC). The performance of the tool is evaluated from the point of view of its wear intensity, mechanism of failure and generation and effect of chatter on tool wear and vice versa. The investigations were aimed at determining the effect of cutting parameters, specifically cutting speed, feed and depth of cut, on chatter amplitude, tool wear rate, mechanism of tool wear and using these data and machined surface roughness values from previous work to come up with recommended values of cutting parameters for semi-finish and finish end milling operation of stainless steel work materials. For recording vibration signals a dual channel portable signal analyzers was used and the signals were analyzed using Pulse Multi-analyzer version 4.2 software. Tool wear was measured using an optical microscope with digital readout capabilities along 3 axes. The tool wear mechanisms were studied under a scanning electron microscope (SEM). Results of the investigation show that acceleration amplitudes generally increase with cutting speed and the magnitude of tool flank wears. It has been also found that an increase in feed and depth of cut leads to higher acceleration amplitudes. The most common wear mechanisms observed during machining of stainless steel are attrition, micro and macro chipping of the tool at lower cutting speeds, and diffusion and mechanical failures due to intensive chatter at higher speeds. It has been also established that stable cutting speeds with relatively low tool wear intensity and satisfactory machined surface finish can be achieved through proper selection of cutting parameters. A table of recommended cutting conditions has been developed for almost chatter free machining with low tool wear intensity and satisfactory surface finish. Key Words: Vertical Machining Centre, Machinability, Chatter, Cutting, Tool life.

Tool Wear Analysis in End Milling of Advanced Ceramics with TiAlN and TiN Coated Carbide Inserts

2012 ◽  
Vol 576 ◽  
pp. 76-79
Author(s):  
M. Mohan Reddy ◽  
Alexander Gorin ◽  
Khaled A. Abou-El-Hossein ◽  
D. Sujan ◽  
Mohammad Yeakub Ali ◽  
...  
Keyword(s):  
Tool Wear ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Speed ◽  
High Hardness ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting ◽  
Coated Carbide ◽  
Axial Depth

Advanced ceramic materials are difficult to machine by conventional methods due to the brittle nature and high hardness. The appropriate selection of cutting tool and cutting conditions may help to improve machinability by endmilling. Performance of TiAlN and TiN coated carbide tool insert in end milling of machinable glass ceramic has been investigated. Several dry cutting tests were performed to select the optimum cutting parameters for the endmilling in order to obtain better tool life. In this work, a study was carried out on the influence of cutting speed, feed rate and axial depth of cut on tool wear.The technique of design of experiments (DOE) was used for the planning and analysis of the experiments. Tool wear prediction model was developed using Response surface methodology.The results indicate that tool wear increased with increasing the cutting speed and axial depth of cut. Effect of feed rate is not much significant on selected range of cutting condition

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

Investigation on the Tool Wear Model and Equivalent Tool Life in End Milling Titanium Alloy Ti6Al4V

2018 ◽  
Author(s):  
Kai Guo ◽  
Bin Yang ◽  
Jie Sun ◽  
Vinothkumar Sivalingam
Keyword(s):  
Tool Wear ◽  
Titanium Alloys ◽  
Tool Life ◽  
End Milling ◽  
Cutting Speed ◽  
Carbide Tool ◽  
Wear Model ◽  
Wear Process ◽  
Coated Carbide Tool ◽  
Coated Carbide

Titanium alloys are widely utilized in aerospace thanks to their excellent combination of high-specific strength, fracture, corrosion resistance characteristics, etc. However, titanium alloys are difficult-to-machine materials. Tool wear is thus of great importance to understand and quantitatively predict tool life. In this study, the wear of coated carbide tool in milling Ti-6Al-4V alloy was assessed by characterization of the worn tool cutting edge. Furthermore, a tool wear model for end milling cutter is established with considering the joint effect of cutting speed and feed rate for characterizing tool wear process and predicting tool wear. Based on the proposed tool wear model equivalent tool life is put forward to evaluate cutting tool life under different cutting conditions. The modelling process of tool wear is given and discussed according to the specific conditions. Experimental work and validation are performed for coated carbide tool milling Ti-6Al-4V alloy.

Sign in / Sign up

Export Citation Format

Share Document