Whole multiple location and universals

2021 ◽  
Author(s):  
Daniel Giberman
Keyword(s):  
Multiple Location

scholarly journals Prediction of rear-end conflict frequency using multiple-location traffic parameters

2021 ◽  
Vol 152 ◽  
pp. 106007
Author(s):  
Christos Katrakazas ◽  
Athanasios Theofilatos ◽  
Md Ashraful Islam ◽  
Eleonora Papadimitriou ◽  
Loukas Dimitriou ◽  
...  
Keyword(s):  
Multiple Location ◽  
Conflict Frequency

Design of Laterally Loaded Plating—Concentrated Loads

1983 ◽  
Vol 27 (04) ◽  
pp. 252-264
Author(s):  
Owen Hughes
Keyword(s):  
Experimental Data ◽  
Load Parameter ◽  
Uniform Pressure ◽  
Concentrated Loads ◽  
Rigid Plastic ◽  
Concentrated Load ◽  
Load Effect ◽  
Permanent Set ◽  
Multiple Location ◽  
Single Location

In the design of plating subject to lateral loading, the principal load effect to be considered is the amount of permanent set, that is, the maximum permanent deflection in the center of each panel of plating bounded by the stiffeners and the crossbeams. The present paper is complementary to a previous paper [1]2 which dealt with uniform pressure loads. It first shows that for design purposes there are two types of concentrated loads, depending on the number of different locations in which they can occur; single location or multiple location. The hypothesis is then made that for multiple-location loads the eventual and stationary pattern of plasticity which is developed in the plating is very similar to that for uniform pressure loads, and hence the value of permanent set may be obtained by using the same formula as for uniform pressure loads, with a load parameter Q that is some multiple r of the load parameter for the concentrated load: 0 = rQP. The value of r is a function of the degree of concentration of the load and is almost independent of plate slenderness and aspect ratio. The general mathematical character of this function is established from first principles and from an analysis of the permanent set caused by a multiple-location point load acting on a long plate. The results of this theoretical analysis provide good support for the hypothesis, as do also the relatively limited experimental data which are available. The theory and the experimental data are combined to obtain a simple mathematical expression for r. A more precise expression can be obtained after further experiments have been performed with more highly concentrated loads. Single-location loads produce a different pattern of plasticity and require a different approach. A suitable design formula is developed herein by performing regression analysis on the data from a set of experiments performed with such loads. Both methods presented herein, one for multiple-location loads and the other for single-location loads, are valid for small and moderate values of permanent set and can be used for all static and quasistatic loads. Dynamic loads and applications involving large amounts of permanent set require formulas based on rigid-plastic theory. Such formulas are available for uniform pressure loads and were quoted in reference [1]. A formula for single-location loads has recently been derived by Kling [4] and is quoted herein.

scholarly journals Alignment of separated patches: multiple location tags

1999 ◽  
Vol 39 (4) ◽  
pp. 789-801 ◽  
Author(s):  
Hiromi Akutsu ◽  
Paul V. McGraw ◽  
Dennis M. Levi
Keyword(s):  
Multiple Location

PLANNING MULTIPLE LOCATION INVENTORIES

2003 ◽  
Vol 24 (2) ◽  
pp. 65-89 ◽  
Author(s):  
Ronald H. Ballou ◽  
Apostolos Burnetas
Keyword(s):  
Multiple Location

scholarly journals Multiple location profiling for users and relationships from social network and content

2012 ◽  
Vol 5 (11) ◽  
pp. 1603-1614 ◽  
Author(s):  
Rui Li ◽  
Shengjie Wang ◽  
Kevin Chen-Chuan Chang
Keyword(s):  
Social Network ◽  
Multiple Location

scholarly journals Agronomic performance of hard endosperm Opaque-2 corn populations in Puerto Rico

1969 ◽  
Vol 72 (2) ◽  
pp. 309-317
Author(s):  
Linda Wessel-Beaver ◽  
César Cardona Castro ◽  
Paul R. Hepperly
Keyword(s):  
Puerto Rico ◽  
Grain Yield ◽  
Agronomic Performance ◽  
Multiple Location ◽  
Ear Height ◽  
The Mean

Six hard endosperm (modified) opaque-2 (o2) corn populations from CIMMYT were compared with local corn cultivars Diente de Caballo and Mayorbela. Grain yield, days to 50% anthesis, plant and ear height, endosperm modification, and lodging were measured. Diente de Caballo was very late in flowering, whereas Mayorbela was earlier than the mean of the o2 genotypes, Diente de Caballo and Mayorbela were taller than o2 genotypes; thus they were more susceptible to lodging. Diente de Caballo was higher yielding than o2 genotypes, but Mayorbela ranked among the lowest yielders at all locations. The· magnitude of the local x genotype variance suggests that multiple location testing would be needed to distinguish between yield and degree of modification of different genotypes. Other traits studied could be tested at one location.

Sign in / Sign up

Export Citation Format

Share Document