A finite element analysis of the optimal bending angles in a running loop for mesial translation of a mandibular molar using indirect skeletal anchorage

2017 ◽  
Vol 21 (1) ◽  
pp. 63-70 ◽  
Author(s):  
M.-J. Kim ◽  
J. H. Park ◽  
Y. Kojima ◽  
K. Tai ◽  
J.-M. Chae
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Skeletal Anchorage ◽  
Element Analysis ◽  
Mandibular Molar ◽  
Bending Angles

Comparison of the effects of different types of maxillary protraction on the maxilla with finite element analysis

2021 ◽  
pp. 1-18
Author(s):  
Muhammed Hilmi Buyukcavus ◽  
Burak Kale
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Face Mask ◽  
Skeletal Anchorage ◽  
Class Iii ◽  
Element Analysis ◽  
Skeletal Class ◽  
Skull Model ◽  
Tensile Forces ◽  
The Face

Abstract Aim: To compare the two different skeletal anchorage methods with finite element analysis in the treatment of Class III patients with maxillary retrognathia. Material and Methods: Two different treatment scenarios were performed on the skull model obtained from computerized tomography images of skeletal Class III patients with maxillary retrognathia and finite element analysis was performed. In the first group; mini plates were simulated on the infra zygomatic crest. A unilateral 500 g protraction force was applied to the face-mask. In the second group; mini plates were simulated in the infrazigomatic crest and mandibular symphysis. Then, 500g protraction force was applied with Class III elastic between the miniplates. Von Misses stresses and displacement values were evaluated comparatively. Results: In the Class III elastic group, maximum Von Misses stress occurred around the infra zygomatic crest and symphysis anchored with 0.078MPa. The maxillary posterior region and paranasal regions were the areas that showed the highest Von Misses tension after infra zygomatic crest and symphysis. In the face-mask group, the most common site of Von Misses stress in the nasomaxillary complex and alveolar structures were the infra zygomatic area where plaques were applied, followed by pterygomaxillary suture. Tensile forces are reduced especially in these two areas by spreading to the surrounding structures. Conclusion: In both methods, it was determined that the amount of force transmitted to the circumaxillary sutures was sufficient to induce the formation of osteogenesis in these regions. Keywords: skeletal anchorage, Class III malocclusion, finite element analysis. Continuous...

scholarly journals Effect of Offset Implant Placement on the Stress Distribution Around a Dental Implant: A Three-Dimensional Finite Element Analysis

2015 ◽  
Vol 41 (6) ◽  
pp. 646-651 ◽  
Author(s):  
Hakimeh Siadat ◽  
Shervin Hashemzadeh ◽  
Allahyar Geramy ◽  
Seyed Hossein Bassir ◽  
Marzieh Alikhasi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Stress Distribution ◽  
Dental Implant ◽  
Three Dimensional ◽  
Element Analysis ◽  
3D Finite Element ◽  
Implant Placement ◽  
Mandibular Molar

There are some anatomical restrictions in which implants are not possible to be inserted in their conventional configuration. Offset placement of implants in relation to the prosthetic unit could be a treatment solution. The aim of this study was to evaluate the effect of the offset placement of implant-supported prosthesis on the stress distribution around a dental implant using 3D finite element analysis. 3D finite element models of implant placement in the position of a mandibular molar with 4 configurations (0, 0.5, 1, 1.5 mm offset) were created in order to investigate resultant stress/strain distribution. A vertical load of 100 N was applied on the center of the crown of the models. The least stress in peri-implant tissue was found in in-line configuration (0 mm offset). Stress concentration in the peri-implant tissue increased by increasing the amount of offset placement. Maximum stress concentration in all models was detected at the neck of the implant. It can be concluded that the offset placement of a single dental implant does not offer biomechanical advantages regarding reducing stress concentration over the in-line implant configuration. It is suggested that the amount of offset should be as minimum as possible.

Mandibular anterior intrusion using miniscrews for skeletal anchorage: A 3-dimensional finite element analysis

2018 ◽  
Vol 154 (4) ◽  
pp. 469-476 ◽  
Author(s):  
Mauricio González del Castillo McGrath ◽  
Víctor Manuel Araujo-Monsalvo ◽  
Noriko Murayama ◽  
Marcos Martínez-Cruz ◽  
Roberto Justus-Doczi ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Skeletal Anchorage ◽  
Element Analysis ◽  
3 Dimensional ◽  
Dimensional Finite Element

scholarly journals THREE-DIMENSIONAL FINITE ELEMENT ANALYSIS OF CLASS 2 INLAY ON MANDIBULAR MOLAR USING VARIOUS MATERIALS

2018 ◽  
Vol 6 (7) ◽  
pp. 272-277
Author(s):  
Maj Pankaj Awasthi ◽  
Lt Col Sonali Sharma ◽  
Maj Summerdeep Kaur
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Stress Analysis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Tooth Structure ◽  
Mandibular Molar ◽  
Von Mises ◽  
Mandibular First Molar

Aim: To study the stress distribution in Class 2 Inlay of various materials on Mandibular Molar. Background: Inlays are fabricated using different materials like gold, porcelain or a cast metal alloy. Difference in the modulus of elasticity of the material and tooth structure would lead to generation of stresses leading to failure of the restoration or loss of tooth structure. Finite Element Analysis (FEA) is a mathematical tool for stress analysis in a structure. Von Mises stress being the combination of normal and shear stresses which occur in all directions. This stress has to be given diligent importance while considering the type and material of restoration to achieve long-term success. Methodology: In our study, stress analysis was performed on the mandibular first molar using a stress analysis software (ANSYS). A computer model of mandibular first molar was generated along with generation of an inlay volume using a FEA software preprocessor. The models with the class 2 inlays of different materials were subjected to 350N and 800N load simulating normal masticatory force and bruxism respectively. Maximum and minimum stresses were calculated for each model separately. Results: Von Mises stress distribution for different materials for normal masticatory forces and bruxism were studied and evaluated. Conclusion: The study revealed the maximum and minimum stresses imposed over the tooth and the restoration and provides insight into the areas which are more prone to fracture under the occlusal load.

Sign in / Sign up

Export Citation Format

Share Document